Manual Tuning; To Skip A Preset Channel; Channel Order - Hitachi DV-PF5EUK Instruction Manual

TUNING

Manual Tuning

• Use the remote control for this procedure.
1
Press MENU.
2
Press K or L to select "INITIAL",
then press B.
3
Press K or L to select "CH TUN-
ING", then press B.
4
Press K or L to select "MANUAL",
then press B.
5
Press K or L to select "POSI-
TION", then press B.
• When a weak signal is received
in Manual Tuning mode, you
can change the background to
solid blue or the static screen by pressing
CLEAR/C.RESET.
6
Press the number buttons or (K or L) to select your
desired position number, then press B.
• You can select position number 01-99.
• If "ON" appears on the right side of "SKIP", press K or
L to point to "SKIP". Then, press B to select "OFF".
• If you want to remove scrambled signals, press K or L
repeatedly to point to "DECODER". Then, press B to
select "ON".
7
Press K or L to select "CHANNEL", then press B.
8
Press K or L to start scanning.
• The DVD/VCR tuner will begin to search up or down
automatically. When a channel is found, the DVD/VCR
will stop searching and the picture will appear on the
TV Screen.
• You can select desired channel number by using the
number buttons. You must refer to the following channel
plan table and press three digits to select the channel
number. (To select channel 24, first press "0" and then
press "2" and "4").
• If this is the channel you want, press B.
Channel Plan
CH Indication
01 – 10
21 – 69
74 – 78
80 – 99,100
121 – 141
This DVD/VCR can receive Hyper and Oscar frequency bands.
9
Press MENU to exit.
NOTE:
• To confirm that a channel has been added, press
PROG (K or L).

To Skip a Preset Channel

The channels you can no longer receive or seldom watch can be
set to be skipped when you access channels PROG (K or L).
• Use the remote control for this procedure.
VCR
MENU
TIMER
SET UP
INITIAL
INITIAL
CH TUNING
CLOCK
RF OUT
CH TUNING
AUTO
MANUAL
MOVE
MANUAL
P08
POSITION
008
CHANNEL
[OFF]
DECODER
[OFF]
SKIP
TV Channel
IRA-IRJ, GAP
E21 – E69
S01, S02, S03, X, Y
S1 – S20,GAP
S21 – S41
VCR
– 17 –
1
Press MENU.
2
Press K or L to select "INITIAL",
then press B.
3
Press K or L to select "CH TUN-
ING", then press B.
4
Press K or L to select "MANUAL",
then press B.
5
Press K or L to select "POSITION", then press B B .
• When a weak signal is received in Manual Tuning
mode, you can change the background to solid blue or
the static screen by pressing CLEAR/C.RESET.
6
Press the number buttons or (K or L) to select relevant
position number, then press B.
7
Press K or L to select "SKIP",
then press B to select "ON".
• To memorise the channel again,
press B "ON" will change to
"OFF".
8
Press MENU to exit.
NOTE:
• To confirm that a channel has been deleted, press
PROG (K or L).

Channel Order

You can arrange the channels in any order you want as fol-
lows.
• Use the remote control for this procedure.
1
Press MENU.
2
Press K or L to select "INITIAL",
then press B.
3
Press K or L to select "CH TUN-
ING", then press B.
4
Press K or L repeatedly to select
"MOVE", then press B.
5
Press K or L repeatedly to select
the position number you want to
change the channel, then press
B.
• You cannot select a position
number where "---" appears next
to the number. This is because
SKIP is set to "ON" for this posi-
tion number.
• When a weak signal is received
in Channel Order mode, you can change the back-
ground to solid blue by pressing CLEAR/C.RESET. If
you press the button again, the background will return
to the static screen.
6
Press K or L repeatedly until the
channel move to another position
number, then press B.
7
Press MENU to exit.
MENU
TIMER
SET UP
INITIAL
INITIAL
CH TUNING
CLOCK
RF OUT
CH TUNING
AUTO
MANUAL
MOVE
MANUAL
POSITION P08
CHANNEL 008
DECODER [OFF]
[ON]
SKIP
VCR
MENU
TIMER
SET UP
INITIAL
INITIAL
CH TUNING
CLOCK
RF OUT
CH TUNING
AUTO
MANUAL
MOVE
MOVE
P01: 02 P06: 07
P02: 03 P07: 08
[ ]
P03: 04 P08: 09
P04: 05 P09: 10
P05: 06 P10: 11
Position
Channel
Number
Number
MOVE
P01: 02 P06: 07
P02: 03 P07: 08
P03: 11 P08: 09
P04: 05 P09: 10
[ ]
P05: 06 P10: 04
EN