Operation Selection Of The Operation Panel; Terminal Assignment Of Output Terminal; Function Assignment Of Input Terminal - Mitsubishi Electric FR-F700 Manual

Operation selection of the
Pr.
161
operation panel
Pr.161 Frequency setting/key lock operation selection
You can use the setting dial of the operation panel (FR-DU07)
like a potentiometer to perform operation.
The key operation of the operation panel can be disabled.
Pr.161 Setting
0 (initial value) Setting dial frequency setting mode
1 Setting dial potentiometer mode
10 Setting dial frequency setting mode
11 Setting dial potentiometer mode
Refer to the section about Pr. 57 and
Pr.
162 to 165
other relevant parameters.
Refer to the section about Pr. 150 and
Pr.
166, 167
other relevant parameters.
Parameter for manufacturer setting. Do not set.
Pr.
168, 169
Refer to the section about Pr. 52 and
Pr.
170, 171
other relevant parameters.
Refer to the section about Pr. 160 and
Pr.
172 to 174
other relevant parameters.
Function assignment of
Pr.
178 to 189
input terminal
Pr.178 STF terminal function selection
Pr.180 RL terminal function selection
Pr.182 RH terminal function selection
Pr.184 AU terminal function selection
Pr.186 CS terminal function selection
Pr.188 STOP terminal function selection Pr.189 RES terminal function selection
Use these parameters to select/change the input terminal functions.
Pr.178 to
Signal
Pr.189
Name
Setting
Pr.59 =0
0 RL (initial value)
Pr.59 =1, 2
Pr.59 =0
1 RM (initial value)
Pr.59 =1, 2
Pr.59 =0
2 RH (initial value)
Pr.59 =1, 2
3 RT Second function selection
4 AU Terminal 4 input selection
5 JOG Jog operation selection
Selection of automatic restart after instantaneous
6 CS
power failure, flying start
7 OH External thermal relay input
15 speed selection
8 REX
(combination with three speeds RL, RM, RH)
Inverter operation enable signal
10 X10
(FR-HC, FR-CV connection)
FR-HC connection, instantaneous power failure
11 X11
detection
12 X12 PU operation external interlock
14 X14 PID control valid terminal
16 X16 PU-external operation switchover
24 MRS Output stop
25 STOP Start self-holding selection
Forward rotation command
60 STF
(assigned to STF terminal (Pr. 178) only)
Reverse rotation command
61 STR
(assigned to STR terminal (Pr. 179) only)
62 RES Inverter reset
PTC thermistor input
63 PTC
(assigned to AU terminal (Pr. 184) only)
64 X64 PID forward/reverse action switchover
65 X65 NET/PU operation switchover
66 X66 External/NET operation switchover
67 X67 Command source switchover
9999  No function
*1 When Pr. 59 Remote function selection = "1" or "2", the functions of the RL,
RM and RH signals are changed as given in the table.
*2 The OH signal turns on when the relay contact "opens".
41
indicates simple mode parameters and
Pr.
Description
Key lock mode
invalid
Key lock mode
valid
Pr.179 STR terminal function selection
Pr.181 RM terminal function selection
Pr.183 RT terminal function selection
Pr.185 JOG terminal function selection
Pr.187 MRS terminal function selection
Function
Low speed operation command
Remote setting (setting clear)
*1
Middle speed operation
command
Remote setting (deceleration)
*1
High speed operation command
Remote setting (acceleration)
*1
*2
indicates extended parameters. When setting parameters, refer to the instruction manual (applied) and understand instructions.
Pr.
Terminal assignment of
Pr.
190 to 196
output terminal
Pr.190 RUN terminal function selection Pr.191 SU terminal function selection
Pr.192 IPF terminal function selection
Pr.194 FU terminal function selection
Pr.196 ABC2 terminal function selection
You can change the functions of the open collector output
terminal and relay output terminal.
Pr.190 to Pr.196
Setting
Signal
Name
Positive Negative
logic logic
0 100 RUN
1 101 SU
2 102 IPF
3 103 OL
4 104 FU
5 105 FU2
5 105 FU2
7 107 RBP
10 110 PU
11 111 RY
12 112 Y12
13 113 Y13
14 114 FDN
15 115 FUP
16 116 RL
17  MC1

18 MC2
19  MC3
25 125 FAN
26 126 FIN
45 145 RUN3
46 146 Y46
47 147 PID
64 164 Y64
70 170 SLEEP
90 190 Y90
91 191 Y91
92 192 Y92
93 193 Y93
94 194 ALM2
95 195 Y95
96 196 REM
98 198 LF
99 199 ALM

9999
* Setting can be made for the 75K or more.
Pr. Refer to the section about Pr.4 to Pr.6
232 to 239
Refer to the section about Pr. 72 and other
Pr.
240
relevant parameters.
Pr. Refer to the section about Pr. 125, Pr.126
241
Refer to the section about Pr. 73 and
Pr.
242, 243
other relevant parameters.
Pr.193 OL terminal function selection
Pr.195 ABC1 terminal function selection
Function
Inverter running
Up to frequency
Instantaneous power failure/
undervoltage
Overload alarm
Output frequency detection
Second output frequency
detection
Second output frequency
detection
Regenerative brake prealarm *
PU operation mode
Inverter operation ready
Output current detection
Zero current detection
PID lower limit
PID upper limit
PID forward/reverse rotation
output
Commercial power-supply
switchover MC1
Commercial power-supply
switchover MC2
Commercial power-supply
switchover MC3
Fan fault output
Heatsink overheat pre-alarm
During inverter running and start
command is on
During deceleration at
occurrence of power failure
(retained until release)
During PID control activated
During retry
During PID output suspension
Life alarm
Alarm output 3 (power-off signal)
Energy saving average value
updated timing
Current average monitor signal
Alarm output 2
Maintenance timer signal
Remote output
Minor fault output
Alarm output
No function