Understanding The Basics; Turning Your Tv On Or Off; Selecting The Video Input Source; Selecting A Channel - Dynex DX-40L150A11 User Manual

Understanding the basics

If you select Home Mode (default - has the same settings as the
Energy Savings picture mode), the Choose your TV source screen
opens.
-OR-
If you select Retail Mode (has the same settings as the Vivid
picture mode), a message stating "Are you sure you want Retail
mode? Since in this mode Energy saving is not realized." appears.
Select Yes to proceed or No to exit.
Choose your TV source
Antenna
Cable
Cable/Satellite Box
Scanning for digital channels
MOVE SELECT
ENTER
6 Press or to select Antenna, Cable, or Cable/Satellite
Box, depending on the type of connection you have.
• If you are using an antenna for a standard or HD TV signal,
select Antenna.
• If your cable is connected directly to the TV (without a tuner
box), select Cable.
• If your cable is connected to your TV through a tuner box,
select Cable/Satellite Box.
7 Press when you have made your selection. The channel scan
screen opens.
If you selected Antenna or Cable, your TV automatically scans
for available channels in your area and stores the channel
information in the channel list. This may take several minutes.
While scanning, the TV displays a progress report.
– OR –
If you selected Cable/Satellite Box, the auto scan is not
necessary and the screen will ask you to select the correct input
source for your set top box. Press EXIT to close the menu.
Notes:
• During auto scan, digital programs will be scanned first, then analog
programs. When all available digital programs have been searched,
the screen will ask you to "Press MENU or EXIT if you don't need
analog channel scan." At this point you can press EXIT to exit the
analog channel scan, or just ignore it and the TV will go on scanning.
• Channel scan can take up to 30+ minutes.
You can press EXIT at any time to stop the auto scan, but you will need to
run the auto scan again to create a channel list.
8 Select the corresponding video input source through the INPUT
SOURCE menu.
Note: You can change the menu language or scan for channels at a later
date. For more information, see "Selecting the menu language and
transparency" on page 27 or "Automatically scanning for channels" on
page 18.
Setup Wizard
Channel scan may take 20+ minutes
0 Digital Channels
0 Analog Channels
PREVIOUS
MENU
Understanding the basics

Turning your TV on or off

To turn your TV on or off (standby mode):
1 Plug the power cord into an AC power outlet.
2 Press (power). Your TV turns on and the power indicator LED
turns blue.
3 Press again to turn off your TV. When you turn off your TV, it
goes into standby mode and the power indicator LED turns red.
Warning: When your TV is in standby mode, it is still receiving power. To
completely disconnect power, unplug the power cord.
Note: If your TV does not receive an input signal for 15 minutes, it
automatically goes into standby mode.

Selecting the video input source

To select the video input source:
1 Turn on your TV, then press the INPUT key on the remote, or the
INPUT button on the TV. The INPUT SOURCE menu opens.
Source List
Component 1
Component 2
2 Press or to highlight the video source, then press ENTER.
You can also select the input source using the following remote
control buttons:
• TV—Press to switch to TV mode.
• VIDEO—Press once to select AV1 and twice to select AV2.
• COMP—Press once to select Component 1 and twice to
select Component 2.
• HDMI–Press repeatedly to cycle between the HDMI inputs.
• VGA—Press to view a computer connected to the TV.

Selecting a channel

To select a channel:
• Press CH or CH
• Press the number buttons to enter the channel number you want,
then wait for the channel to change, or press ENTER to change
the channel immediately.
• To select a digital channel, press the number buttons to
select the main digital channel, then press the dot (.) button,
then the number buttons again to select the sub-channel.
Wait for the channel to change or press ENTER to change the
channel immediately. For example, enter 13, then . (dot),
then 1 to go to channel 13.1.
Note: Button presses must be within three seconds of each other.
• Press RECALL to go to the last channel viewed.
• Press FAVORITE to display a list of your saved favorite channels,
press or to select the channel you want from the list, then
press ENTER to go to that channel.
Note: If the list has more than one page, press
the pages.
DX-40L150A11
TV
AV 1
AV 2
VGA
HDMI 1
HDMI 2
HDMI 3
HDMI 4
to go to the next or previous channel.
or to scroll through
13