Chapter 22
Wireless Device Troubleshooting
extracting c350-k9w7-mx.122-13.JA1/html/level1/appsui.js (558 bytes)
extracting c350-k9w7-mx.122-13.JA1/html/level1/back.htm (205 bytes)
extracting c350-k9w7-mx.122-13.JA1/html/level1/cookies.js (5027 bytes).
extracting c350-k9w7-mx.122-13.JA1/html/level1/forms.js (15704 bytes)...
extracting c350-k9w7-mx.122-13.JA1/html/level1/sitewide.js (14621 bytes)...
extracting c350-k9w7-mx.122-13.JA1/html/level1/config.js (2554 bytes)
extracting c350-k9w7-mx.122-13.JA1/html/level1/stylesheet.css (3215 bytes)
c350-k9w7-mx.122-13.JA1/html/level1/images/ (directory) 0 (bytes)
extracting c350-k9w7-mx.122-13.JA1/html/level1/images/ap_title_appname.gif (1422 bytes)
extracting c350-k9w7-mx.122-13.JA1/html/level1/images/apps_button_1st.gif (1171 bytes)
extracting c350-k9w7-mx.122-13.JA1/html/level1/images/apps_button_cbottom.gif (318 bytes)
extracting c350-k9w7-mx.122-13.JA1/html/level1/images/apps_button_current.gif (348 bytes)
extracting c350-k9w7-mx.122-13.JA1/html/level1/images/apps_button_last.gif (386 bytes)
extracting c350-k9w7-mx.122-13.JA1/html/level1/images/apps_button_last_filler.gif (327
bytes)
extracting c350-k9w7-mx.122-13.JA1/html/level1/images/apps_button_last_flat.gif (318
bytes)
extracting c350-k9w7-mx.122-13.JA1/html/level1/images/apps_button_nth.gif (1177 bytes)
extracting c350-k9w7-mx.122-13.JA1/html/level1/images/apps_leftnav_dkgreen.gif (869 bytes)
-- MORE --
Note
Enter the set BOOT command to designate the new image as the image that the wireless device uses
Step 8
when it reboots. The wireless device creates a directory for the image that has the same name as the
image, and you must include the directory in the command. Your entry might look like this example:
ap: set BOOT flash:/c350-k9w7-mx.122-13.JA1/c350-k9w7-mx.122-13.JA1
Enter the set command to check your bootloader entries.
Step 9
ap: set
BOOT=flash:/c350-k9w7-mx.122-13.JA1/c350-k9w7-mx.122-13.JA1
DEFAULT_ROUTER=192.168.133.1
IP_ADDR=192.168.133.160
NETMASK=255.255.255.0
Enter the boot command to reboot the wireless device. When the wireless device reboots, it loads the
Step 10
new image.
ap: boot
Obtaining the Access Point Image File
You can obtain the wireless device image file from the Cisco.com by following these steps:
Use your Internet browser to access the Cisco Software Center home page:
Step 1
http://www.cisco.com/cisco/software/navigator.html
Expand the Wireless LAN Access folder.
Step 2
Step 3
Expand the appropriate access point folder.
Step 4
Select the appropriate access point.
Step 5
Enter your CCO login and password. The Select Software page appears.
OL-14209-01
If you do not press the spacebar to continue, the process eventually times out and the wireless
device stops inflating the image.
Cisco IOS Software Configuration Guide for Cisco Aironet Access Points
Reloading the Access Point Image
22-25