Table of Contents
Advertisement
Rotary Tool Owner's Manual
Models 275T6 (F013027503)
HONESTLY NOW ... Have you read
this OWNER'S MANUAL?
• Safety
• Assembly
• Operation
• Maintenance
• Attachment Information
• Accessory Information
• Warranty
• Service Parts
1-800-437-3635
http://www.dremel.com
Dremel brand products are manufactured and sold by the
2610916195 4/03
285T6 (F013028503)
395T6 (F013039504)
P.O. Box 1468
Racine, Wisconsin 53401
Dremel Division of Robert Bosch Tool Corporation
MultiPro
™
Parlez-vous français?
Voir page 27
¿Habla español?
Vea página 55
©
Robert Bosch Tool
Corporation
2001
All Rights Reserved
PRINTED IN U.S.A.
Advertisement
Table of Contents
Related Manuals for Dremel MultiPro 395T6
Summary of Contents for Dremel MultiPro 395T6
- Page 1 • Service Parts P.O. Box 1468 © Racine, Wisconsin 53401 Robert Bosch Tool Corporation 1-800-437-3635 2001 All Rights Reserved http://www.dremel.com Dremel brand products are manufactured and sold by the Dremel Division of Robert Bosch Tool Corporation 2610916195 4/03 PRINTED IN U.S.A.
-
Page 2: Work Area
Power Tool Safety Rules Read and understand all instructions. Failure to follow all instructions listed below, may WARNING result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area power tools may result in serious personal injury. Keep your work area clean and well lit. - Page 3 Use only accessories that are recommended by the When servicing a tool, use only identical replacement manufacturer for your model. Accessories that may parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to be suitable for one tool, may become hazardous follow Maintenance Instructions may create a risk of when used on another tool.
- Page 4 Safety Rules for Rotary Tools - (cont.) Inspect your workpiece before cutting. When cutting Do not alter or misuse tool. Any alteration or irregularly shaped workpieces, plan your work so it modification is a misuse and may result in serious will not slip and pinch the bit and be torn from your personal injury.
- Page 5 Symbols MPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. Symbol Name Designation/Explanation Volts Voltage (potential) Amperes Current Hertz...
-
Page 6: Functional Description And Specifications
Functional Description and Specifications Disconnect the plug from the power source before making any assembly, WARNING adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally. Rotary Tool 275T6 & 285T6 CORD HANGER VENTILATION HOUSING CAP OPENINGS COLLET... -
Page 7: Flex-Shaft
Flex-Shaft 225 DRIVER FLEXIBLE SHAFT CORE OVERTHROW NUT HANDPIECE ASSEMBLY COLLET COLLET WRENCH Cutting Guide 565 Grout Removal Kit 568 DEPTH DEPTH ADJUSTMENT GUIDE ADJUSTMENT GUIDE SCREW INSERT SCREW INSERT Right Angle Attachment 575 COLLAR COLLET COLLET ADAPTER Page 7... -
Page 8: Assembly
COLLETS — Four different size collets (see illus- tration), to accommodate different shank sizes, are DREMEL KEYLESS CHUCK available for your Rotary Tool. To install a different Use only with black chuck collet, remove the collet nut and remove the old collet. -
Page 9: Operating Instructions
To learn The speed enables it to do jobs low speed tools about more uses and the versatility of Dremel cannot do, such as cutting hardened steel, engraving accessories and attachments refer to this Owner's glass, etc. - Page 10 You should not lean on or push the tool during use. Questions or Problems?Call 1-800-437-3635 or check our website at www.Dremel.com For best control in close work, grip the Rotary Tool The “Golf Grip” method of holding the tool is used like a pencil between your thumb and forefinger.
-
Page 11: Operating Speeds
Rotary Tool should be regu- lated. Only a full wave output speed control such as Slow speeds (15,000 RPM or less) usually are best the Dremel Model 221 should be used with the for polishing operations employing the felt polishing 275T6 Rotary Tool. - Page 12 Operating Speeds - (Cont.) If you need it, single-speed models also can have Ultimately, the best way to determine the correct speed speed control by using a Model 221 foot control unit. for work on any material is to practice for a few minutes on a piece of scrap, even after referring to the Not for use with variable speed CAUTION...
- Page 13 Too much handpiece. If tool stops when shaft is bent, center grease will cause the unit to overheat. Dremel shaft core may be lodged in driver cap. Loosen shaft and lubricant No. 5990952 or automotive wheel bearing remove core from driver cap.
- Page 14 Assembly & Operation of Attachments - (Cont.) Do not operate the flexible shaft WARNING with a sharp bend. This can generate excessive heat and will reduce tool and flex- shaft life. The recommended minimum is 5" radius. Contents of 225 Flex-Shaft Attachment: Qty.
- Page 15 When inserting the #569 or #570 CAUTION grout removal bit into your Dremel rotary tool, be sure that the bit is secure within the “jaws” of the collet. Use the wrench to tighten the collet nut to prevent the bit from loosening within the collet.
- Page 16 Assembly & Operation of Attachments - (Cont.) Operating Instructions Always pull the tool toward you! WARNING Do not push it! Pushing the bit may cause it to break. Hold the tool in a golf grip with the tool positioned below the attachment and the bit pointing upwards.
- Page 17 Right Angle Attachment 575 Screw the attachment onto your rotary tool. Hand tighten only. Reassemble the collet and the collet nut from step 2, on to the output shaft of the attachment. Before you begin, remove the black protective cap on Figure 4.
-
Page 18: Extension Cords
50 - 60 hours the brushes To avoid accidents always dis- WARNING be examined. Only genuine Dremel replacement brushes connect the tool from the power specially designed for your tool should be used. supply before cleaning or performing any main- tenance. - Page 19 Dremel Attachments Add these Dremel attachments to your compact workshop and make your Rotary Tool more versatile. 330 - Router Attachment Shapes, edges, chamfers, cuts, 565 - Multipurpose Cutting Kit 566 - Tile Cutting Kit rabbets, dadoes, etc. Adjustable • Includes 2 drywall cutting bits •...
- Page 20 Dremel Accessories Use only Dremel Tested, High Performance Accessories. Other accessories are not WARNING designed for this tool and may lead to personal injury or property damage. The number and variety of accessories for the Rotary Tool are almost limitless. There is a category suited to Tungsten Carbide Cutters almost any job you might have to do —...
- Page 21 Polishing Accessories Wire Brushes These include an impregnated polishing point and an Three different shapes of wire brushes are available. impregnated polishing wheel for bringing metal sur- Never use wire brushes at speeds greater than faces to smooth finish; a felt polishing tip and felt 15,000 RPM.
- Page 22 High Speed Router Bits Drywall Cutting Bit For routing, inlaying, and mortising in wood and other Gives you fast, clean cuts in drywall. soft materials. Use only with Dremel No. 330 Router attachment or No. 231 Shaper/Router table. Page 22...
- Page 23 Mandrel No. 401 is used with the felt polishing tip and wheels. Thread the tip on to the screw carefully. The felt tip must thread down straight on the screw Mandrel, and be turned all the way to the collar. Mandrel No.
- Page 24 Page 24...
- Page 25 Page 25...
- Page 26 Page 26...
- Page 27 Pagina 85...
- Page 28 Pagina 86...
- Page 29 Pagina 87...
- Page 30 Pagina 88...
- Page 31 Pagina 89...
- Page 32 Pagina 90...
- Page 33 Pagina 91...
- Page 34 Dremel Limited Warranty Your Dremel Rotary Tool is warranted against defective material or workmanship for a period of five years from date of purchase. In the event of a failure of a product to conform to this written warranty, please take the following action: 1.