Installation Instructions; Things You Need To Know; Warnings; Things To Note - Electrolux EOD6330 Owner's Manual

INSTALLATION INSTRUCTIONS

THINGS YOU NEED TO KNOW

WARNINGS:

·
This appliance must be installed by a qualified
electrician/competent person.
impaired if installation is not carried out in
accordance with these instructions.
· This appliance must be earthed.
· Do not remove the screws from the earth tab
extending from the oven mains terminal block
(Fig. 6).
· Before connecting the appliance make sure that
the voltage of your electricity supply is the same
as that indicated on the rating plate. This is
situated on the front frame of the appliance and
can be seen upon opening the door. Alternatively
the rating plate may also be found on the back or
top of some models (where applicable).
·
Do not alter the electrical circuitry of this
appliance.

THINGS TO NOTE

·
This appliance is designed to be fitted in cabinets
of the recommended dimensions as shown
(Fig.2).
·
If your cabinet interior dimension is between 565-
570mm the oven may still be fitted. However, a
minor modification to the cabinet will be required
to reduce the aperture size down to 560-565 mm,
to allow the product to be securely screwed into
the cabinet.
·
The dimensions given provide adequate air
circulation around the unit within the cabinet,
ensuring compliance with BS EN60-335.
·
Enquiries regarding the installation of the cooker
point, if required, should be made to your
Regional Electricity
compliance with their regulations.
· The appliance socket switch should be outside
the cabinet but within 2m of the appliance to
make it accessible to switch off the appliance in
case of an emergency.
·
To protect the hands, wear gloves when lifting
the oven into its housing.
NOTE: HOUSE CIRCUIT
Earth leakage and continuity tests must be carried
out before the appliance is connected to the mains
supply and re-checked after fitting.

GETTING THINGS READY

CHOICE OF ELECTRICAL CONNECTION

·
There are three possible ways to connect your
appliance. In each case the appliance should be
operated using at least 6mm
PVC insulated multicore cable. Please choose
from the most appropriate after reading the
different methods:-
Safety may be
Company to ensure
2
twin core and earth
a) By connecting to a cooker point (having a double
pole isolating switch with at least 3mm contact
separation in all poles and neutral) and protected
with a fuse or miniature circuit breaker at your
mains fuse box.
Subject to Regional Electricity Companies
regulations if you wish to connect the oven
and hob to the power supply you may use
one of the following two methods:-
b) By connecting the appliance together with a hob
directly to a cooker point(s). Having a double
pole isolating switch with at least 3mm contact
separation in all poles and neutral.
c) If you wish to connect an oven and a hob to a
cooker point you can by connecting the oven and
hob separately to the cooker point. Oven and
hob units should be separately connected to a
cooker point. See Fig. 1.
Fig. 1
NOTE: It is good practice to :
·
Fit an Earth Leakage Circuit Breaker to your
house wiring.
·
Wire your appliance to the latest IEE regulations.
PREPARING CABINET FOR FITTING OF OVEN
·
Make sure that the cabinet is the correct size for
the appliance to be fitted (Ref. Fig. 2).
· If the size is between 565-570mm, then the
cabinet should be modified so that at the screw
fixing points the recommended dimension of at
least 560-565mm
modification should ideally be localised to ensure
that after screw fitment the oven is securely
fixed into position.
· The cabinet must be stable and level by firmly
securing it to the wall or floor.
make arrangements to ensure the shelf upon
which the oven will rest is level.
·
When the appliance is installed ensure a
minimum gap of 2mm is maintained between the
trim on the bottom edge of the appliance, and
any corresponding door / panel underneath.
7
is maintained. The
If necessary,