Panasonic BB-HCM701CE Important Information

Important Information
Network Camera
BB-HCM701
Model No.
BB-HCM705
How to Use the Documentation
This manual is written for both the BB-HCM701 and the BB-HCM705.
Available features and operations vary slightly depending on the model. You
can confirm the model no. of your camera by checking the model no. printed
on the front of the camera.
Model number suffix "CE" is omitted from the following model numbers
shown in this document, unless necessary. BB-HCM701CE, BB-HCM705CE
All documentation can be found on the included CD-ROM.
• Important Information (PDF format; printed version also included)
This document. Provides general information and safety instructions for
using the camera.
• Installation Guide (PDF format; printed version also included)
Describes how to physically connect the camera to the power supply and
network, as well how to mount or place the camera for regular use.
• Setup Guide (PDF format; printed version also included)
Describes how to set up the camera so that it can be accessed using a PC.
• Operating Instructions (HTML format)
Explains how to operate, program, and maintain the camera.
• Troubleshooting Guide (HTML format)
Provides solutions for problems you may have when using the camera.
• Stand-alone SD Memory Card Recording Guide (PDF format; printed
version also included)
Describes how to record images to an SD memory card without using a
PC.
Abbreviations
• The Network Camera is referred to as "the camera" in this document.
• The Setup CD-ROM is referred to as "the CD-ROM" in this document.
• The term "SD memory card" is used in this document to refer to SD
memory cards and SDHC memory cards.

IMPORTANT SAFETY INSTRUCTIONS

When using this unit, basic safety precautions should always be followed to
reduce the risk of fire, electric shock, or personal injury.
Note:
• References to the AC adaptor and the AC cord apply when using the
optional BB-HCA7CE or BB-HCA7E AC Adaptor.
1. Read and understand all instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Attach the Safety Wire to the camera to prevent it from dropping.
6. After taking away the sand or the dust on the lens cover, wipe the lens
cover with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with
instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other devices (including amplifiers) that produce heat.
9. Protect the AC adaptor cord, the AC cord and the extension cord from
being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the unit.
10. The AC cord is used as the main disconnect device. Ensure that the
socket-outlet shall be installed near the equipment and shall be easily
accessible.
11. Only use attachments/accessories (such as the safety wire) specified by
the manufacturer.
12. Do not touch the unit, the LAN cable, the AC adaptor, the AC adaptor
cord, the AC cord and the extension cord during lightning storms.
13. Unplug the unit from power supply when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required
when the unit has been damaged in any way, such as when the AC
adaptor, the AC adaptor cord, or the AC cord is damaged, the unit does
not operate normally, or has been dropped.
15. Prolonged exposure to direct sunlight or halogen light may damage the
image sensor.
16. The camera is intended for indoor use only.
17. Keep the SD memory card (customer-provided) out of reach of children
to prevent swallowing.
18. Unplug this unit from power supply if it emits smoke, an abnormal smell
or makes unusual noise. These conditions can cause fire or electric
shock. Confirm that smoke has stopped and contact an authorized
service center.
© Panasonic System Networks Co., Ltd. 2009
PNQX2141XA KK0909CQ3120 (CE)
Please read this document before using the product, and save this document for future
reference. Panasonic Network Camera Website:
http://panasonic.net/pcc/ipcam/
(PoE Ready)
Indoor Use Only
Indoor Use Only
This installation should be made by a qualified service
person and should conform to all local codes.
19. If for some reason the camera is no longer used, uninstall the camera to
avoid the risk of the camera falling.
SAVE THESE INSTRUCTIONS

Other Information

CAUTION:
• Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
• To reduce the risk of electric shock, do not remove cover (or back).
• The camera is to be connected only to PoE networks without routing to
the outside plant when using PoE.
Environment:
Do not install the camera where the temperature is less than +0 °C or greater
than +40 °C. Allow 10 cm clearance around the unit for proper ventilation.
Avoid excessive smoke, dust, mechanical vibration, shock, or direct sunlight.
Routine care:
Wipe the unit with a soft cloth. Do not use benzine, thinner, or any abrasive
powder.
When you leave the unit unused for a long period of time, disconnect the LAN
cable (when using PoE) from the camera, or disconnect the AC adaptor from
the outlet (when using the optional AC adaptor).
If you have any problems:
Consult an authorized service center.
No responsibility will be taken by our company with respect to
consequences resulting from the use, damage or both of the camera.

Security Cautions

When using this product, take appropriate measures to avoid the following
security breaches.
• Disclosure of private information via this product
• Unauthorized use of this product by a third party
• Interference or suspension of the use of this product by a third party
You are responsible for the security of this product and its use. Take the
following measures to avoid security breaches.
• To prevent unauthorized access, disclosure of private information, or
interference or suspension of access to the camera, make sure the
camera's firmware is up to date.
• Do not reveal the user names and passwords required to access the
camera to an unknown party.
• If you choose to configure this product to allow access to parties without
the need to enter a user name and password (i.e., guest users), be aware
that unknown parties may access this product.
• Do not upload images produced by this product or otherwise release
information where it may be accessed by unknown parties.
• Mount the camera where the camera will not be stolen.
• When sending this product for service or transferring this product to
another party, make backup copies of its setup files, and reset this product
to its factory default settings.
• When disposing of this product, reset the product to its factory default
settings, or erase the product's memory by means of electrical deletion or
physical dismantlement.
• After the camera is accessed by the administrator, make sure to close the
browser for added security.
• Change the administrator password periodically for added security.
User Name and Password Protection
The use of unique user names and secret passwords is an important
tool that will help limit unauthorized individuals from accessing the
camera. If you choose to disable this tool by allowing guest (i.e.
anonymous) access, the camera may be accessed by unauthorized
individuals.
AVC/H.264 Visual License
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO
LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER
USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (I)
ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD ("AVC
VIDEO") AND/OR (II) DECODE AVC VIDEO THAT WAS ENCODED BY A
CONSUMER ENGAGED IN A PERSONAL ACTIVITY AND/OR WAS
OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC
VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY
OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM
MPEG LA, L.L.C. SEE http://www.mpegla.com .