Direct Button Operation; Input; Changing Channels; Changing Volume - Sharp Aquos LC-60LE845U Operation Manual

Direct Button Operation

INPUT

To view external source images, select the input source by
pressing INPUT on the remote control unit or on the TV.
1
Press INPUT.
• The INPUT list screen displays.
Press a / b or press INPUT again to select the
2
input source.
• An image from the selected source automatically
displays.
• Each time INPUT is pressed, the input source toggles.
• If the corresponding input is not plugged in, you cannot
change the input. Be sure to connect the equipment
beforehand.
• See pages 14 to 18 and 57 for external equipment
connection.

Changing Channels

You can change channels in several ways.
Method 1
Using CH on the remote control unit or on the TV.
/
Method 2
Using remote control buttons 0-9, • (DOT).
Examples:
To select a 1 or 2-digit channel number (e. g., Channel 5):
Press 5 ENT.
To select a 3-digit channel number (e. g., Channel 115):
Press 1 1 5
To select a 4-digit channel number (e. g., Channel 22.1):
Press 2 2 • (DOT)
Method 3
Selecting the program from Channel list.
1
Press INPUT on the remote control unit.
• The INPUT list displays.
2 c / d
Press to select "AIR" or "CABLE".
• The Channel list displays.
Press a / b to select the desired channel, and then
3
press ENTER.
• When selecting a 1-digit channel number, it is not
necessary to press 0 before the number.
• When you enter 0-9 only, channel selection will be made if
there is no operation within a few seconds.
• If you push "0" by itself, nothing will happen.
• Complete the above steps within a few seconds.
• When you enter 0-9 and • (DOT), channel selection will be
made if there is no operation within a few seconds.
ENT.
1 ENT.

Changing Volume

You can change the volume by pressing VOL k / l on
the TV or on the remote control unit.
• To increase the volume, press VOL
• To decrease the volume, press VOL
Audio status
Output device
Speaker Variable sound
• When "Output Select" is set to "Variable", the indicator on
the screen changes as shown below.
• See page 34 for details on the Output Select function.

MUTE

Mutes the current sound output.
Press MUTE.
• " " will be displayed on the screen for 30 minutes, and
the sound is silenced.
• Within 30 minutes of pressing MUTE, mute can be
canceled by pressing VOL k / l or MUTE.
• Mute will be canceled after 30 minutes have passed.
However, the TV will not suddenly output a loud sound as
the volume level is set to 0 automatically.

Sleep Timer

Allows you to set a time when the TV automatically
switches to standby.
Press SLEEP.
• The remaining time displays when the sleep timer has been set.
• Each time you press SLEEP, the remaining time switches
as shown below.
Off 30 60 90
• When set, the time automatically starts counting down.
• If you want to adjust the sleep timer, you can press SLEEP
twice then change the time setting.
• When it is 5 minutes before the time expires, the remaining
time will start to keep appearing every minute.
• Select "Off" by pressing SLEEP to cancel the sleep timer.
• The TV will enter standby when the remaining time reaches 0.

FREEZE

Allows you to capture and freeze a moving image that
you are watching.
Press FREEZE.
• A moving image is captured.
• Press FREEZE again to cancel the function.
• When this function is not available, "No displaying still
image available." will display.
• The still image automatically goes out after 30 minutes.
• If you are using the freeze function and a broadcast
activates the V-CHIP BLOCK, the freeze function will be
canceled and a V-CHIP BLOCK message will appear.
• You can have the same settings by choosing "Freeze" on
the menu items. (See page 33.)
k
.
l
.
20
Output Select
Fixed Variable
Mute
60
120
23