Download  Print this page

923.xx-hot Fuser Service Check - Dell 5310n - Workgroup Laser Printer B/W Service Manual

Service manual.
Hide thumbs
   
1
2
Table of Contents
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430

Advertisement

FRU
Fuser assembly
6
923.xx—Hot fuser service check
Error Code 923.xx, 924.xx, and 925.xx may display for a hot fuser failure.
CAUTION: .The fuser may be hot, use caution before removing or servicing.
CAUTION: There is a danger from hazardous voltage in the area of the printer where you are
working. Unplug the printer before you begin, or use caution if the printer must receive power in
order to perform the task.
Service tip: Set the Fuser Temperature to NORMAL before starting this service check. In Diagnostics mode, In
Diagnostics mode, select EP SETUP, and Fuser Temp.
FRU
Fuser assembly
1
Fuser top cover assembly
2
(thermistor)
System board
3
Fuser top cover assembly
Service Manual
2-90
Action
If no problem is found up to this point, then replace the following in
the order shown:
• Fuser assembly. See
"Fuser assembly removal" on page
• System board assembly. See
removal" on page
4-77.
• LVPS. See
"Low voltage power supply removal" on
page
4-55.
Action
Check for any signs of overheating in the fuser assembly. Check the
hot roll, hot roll bearings, and the area around the thermistor for any
signs of excessive heat. If a problem is found, replace the thermistor.
If no problem is found, go to step 2.
Turn the printer off and disconnect the fuser to system board cable
from J10 on the system board. Check the resistance between pins
J10-3 and J10-4. The resistance should be greater than 100K ohms.
If correct, go to step 3; if incorrect, disconnect the thermistor cable
from J5 on the fuser board and measure the resistance between the
two pins on the thermistor cable. If incorrect, replace the fuser top
cover assembly (see
"Fuser narrow media sensor removal" on
4-35); if correct, replace the fuser to system board cable.
page
Check the voltage on J10-3 ground on the system board. The voltage
should measure approximately +3.3 V dc. If the voltage is correct,
replace the fuser top cover assembly. See
sensor removal" on page
board. See
"System board and inner shield removal" on
page
4-77.
"System board and inner shield
"Fuser narrow media
4-35. If incorrect, replace the system
4-27.

Advertisement

Table of Contents

   Related Manuals for Dell 5310n - Workgroup Laser Printer B/W

This manual is also suitable for:

5210n5310n

Comments to this Manuals

Symbols: 0
Latest comments: