Download  Print this page

Envelope Feeder Service Check - Dell 5310n - Workgroup Laser Printer B/W Service Manual

Service manual.
Hide thumbs
   
1
2
Table of Contents
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430

Advertisement

Envelope feeder service check

Service tip: Check the envelope feeder paper path for any debris, pieces of envelope and so on. If any other
options are installed make sure they are operating normally. If only the envelope feeder is failing to operate
correctly, continue with this service check, otherwise verify the interconnect card is functioning properly.
Service tip: The envelope feeder receives its +5 V dc operating voltage from the +24 V dc bulk at J1-7. If
+24 V dc is not present at J1-7, tray 1 is the only tray that is recognized.
Note: If a 260 Paper Jam Check Envelope message displays, check the
error codes" on page
Printer does not recognize the envelope feeder as an attached input option
FRU
Envelope feeder
1
Front autoconnect on
2
printer
Autoconnect on the
3
envelope feeder
Operator panel displays
requested—POST incomplete
FRU
Pass thru sensor
1
Service Manual
2-84
2-8.
Action
Make sure the envelope feeder is correctly installed and mated to the
autoconnect at the front of the printer.
Check the connector for signs of damage to the connector or
contacts. If you find damage, replace the damaged cable/connector
assembly. Remove the envelope feeder and check the voltages at
the autoconnect on the front of the printer. If incorrect, check the
interconnect card. If correct, reinstall the envelope feeder and
continue with step 3.
Check for damage to the connector or contacts. If you find damage,
replace the damaged cable/connector assembly. Disconnect the
autoconnect cable at J1 on the envelope system board and measure
the following voltages:
• J1-3 measures +5 V dc
• J1-5 measures +5 V dc
• J1-7 measures +24 V dc
If any of the voltages are incorrect, replace the autoconnect cable/
connector. If the voltages are correct, replace the envelope system
board.
260.xx Paper Jam
Action
Check for any debris or pieces of envelope over the pass thru
sensor. Check for correct installation of the pass thru sensor flag.
Make sure the sensor cable is attached to the envelope system
board. Perform an envelope feeder sensor test to check both the
sensor and sensor flag.
Note: It may be necessary to use a small tool to actuate the sensor
flag because it is located under the front cover. Be careful not to
damage the flag.
If the test fails, check the flag for damage or binds. If incorrect,
replace the flag. If the flag is operating correctly, check the voltage at
J3-3. The voltage measures approximately +5 V dc. If incorrect,
replace the envelope system board. If correct, check the voltage at
J3-2. The voltage changes from 0 to +5 V dc when the flag is moved
in and out of the sensor. If incorrect, replace the sensor assembly. If
this does not fix the problem, replace the envelope system board.
"Sub error codes for 9xx and 2xx
immediately when envelope feed is

Advertisement

Table of Contents

   Related Manuals for Dell 5310n - Workgroup Laser Printer B/W

This manual is also suitable for:

5210n5310n

Comments to this Manuals

Symbols: 0
Latest comments: