Sanyo CE42LM4WPN-NA - CE - 42" LCD Flat Panel Display Instruction Manual page 2

CAUTION: Please read and retain for your safety. This unit has been engineered and manufactured to assure your personal safety, but
improper use can result in potential electric shock or fire hazards. In order not to defeat the safeguards incorporated in this receiver observe
the following basic rules for its installation, use and servicing.
Installation
WARNING: To prevent injury the LCD monitor must be
securely fixed in accordance with the manufacturers
mounting installation instructions.
This monitor must NOT be permanently mounted to the build-
ing structure. It must be mounted in such a way that it can be
removed using basic tools.
The power supply cord must NOT be attached to the building
surface. The power supply cord must NOT be routed through
walls, ceiling, floors, or other similar openings in the building
structure.
The power supply cord MUST be positioned so as to prevent
physical damage.
Do not allow anything to rest on the power cord. Do not
locate this LCD monitor where the cord will be damaged by
people walking on it.
A suitable socket outlet must be provided near to the monitor
and shall be easily accessible.
Do not overload wall outlets as this can result in fire or elec-
tric shock.
This LCD monitor should not be built in to any structure or
enclosed in any way. Heat build up will reduce the life of the
monitor.
Always mount using recommended and substantial fixtures
and fittings.
Do not place this LCD monitor near any heat sources such as
radiators, heaters, stoves and other heat-generating products
(including amplifiers).
Do not place your LCD monitor on an unstable stand, shelf or
table. Serious injury to an individual, and damage to the LCD
monitor may result if it should fall. Your sales person can
recommend approved wall mounting kit. A special wall mount-
ing kit is available for this model.
This LCD monitor should be operated only from the type of
power source indicated on the monitor or as indicated in the
Operating Instructions. If you are not sure of the type of power
supply, consult your sales person or your local power compa-
ny
For added protection it is strongly recommended that this
monitor is supplied via an approved earth fault protection device
This monitor is not protected against temporary or continuous
immersion in liquid.
This monitor is tested to IP56 (Category 2) standard rating.
Do not use immediately after moving the LCD monitor from a
low temperature to a high temperature environment, as this
causes condensation, which may result in fire, electric shock,
or other hazards. Before cleaning, unplug the monitor from the
wall socket.
Do not mount near an open flame source. Open flames must
never be used near this LCD monitor.
Do not apply liquid cleaners or aerosol cleaners directly onto
the LCD monitor. Use a damp cloth for cleaning.
The rear finned section around the cabinet functions as a heat
sink, removing heat away from the monitor. The external sur-
face of the cabinet (finned area) must not be covered or the
airflow resricted in anyway by enclosing the LCD monitor
The operating temperature range of this monitor can be used
at 32°F ~ 104°F. It is not recommended to install the screen
in direct sunlight without adequate shading, as this will cause
the temperature of the panel to rise above the maximum spec-
ified.
Doing so may cause a black shadow to appear on the screen,
which will disappear when the screen temperature returns to
within the specification. This "of course" does not produce any
2
SAFETY PRECAUTIONS & SERVICING
SAFETY PRECAUTIONS & SERVICING
Use
harmful effect on the lifetime of the panel.
This LCD monitor should have a minimum distance of 5cm
away from the wall and the monitor should have 10cm dis-
tance around the top and sides
10cm
Your LCD monitor is fully transistorised and does not contain
any user serviceable components.
You must not remove the rear cover of the LCD monitor by your-
self. The apparatus is working with high voltages and could
damage objects or even endanger people. Leave all required
repair and service jobs to an authorised service technician. He
will exclusively use such spare parts that are complying with the
same safety standards as applicable to the original parts. The
use of original spare parts can prevent fire, shock and other haz-
ards.
Unplug the LCD monitor from the wall outlet and refer servicing
to qualified service personnel under the following conditions:
If the power cord or plug is damaged.
If the has been dropped or the cabinet has been damaged.
monitor
If the LCD
LCD monitor
If the
operating instructions.
LCD
Adjust only those controls that are covered in the operating instruc-
tions as improper adjustment of other controls may result in damage.
This will often require extensive work by a qualified technician to
LCD monitor
restore the
10cm
10cm
Servicing
exhibits a distinct change in performance.
does not operate normally by following the
to normal operation.
5cm