Displaying Ipv4 Bidirectional Pim Information - Cisco 7604 Configuration Manual

Chapter 28 Configuring IPv4 Multicast Layer 3 Switching

Displaying IPv4 Bidirectional PIM Information

To display IPv4 bidirectional PIM information, perform one of these tasks:
Command
Router# show ip pim rp mapping [in-use]
Router# show mls ip multicast rp-mapping
Router# show mls ip multicast rp-mapping gm-cache
Router# show mls ip multicast rp-mapping df-cache
Router# show mls ip multicast bidir
Router# show ip mroute
This example shows how to display information about the PIM group and rendezvous point mappings:
Router# show ip pim rp mapping
PIM Group-to-RP Mappings
This system is an RP (Auto-RP)
This system is an RP-mapping agent
Group(s) 230.31.0.0/16
RP 60.0.0.60 (?), v2v1, bidir
RP 50.0.0.50 (?), v2v1, bidir
RP 40.0.0.40 (?), v2v1, bidir
This example shows how to display information in the IP multicast routing table that is related to IPv4
bidirectional PIM:
Router# show ip mroute bidirectional
OL-4266-08
[
rp_address
Info source:60.0.0.60 (?), elected via Auto-RP
Uptime:00:03:47, expires:00:02:11
Info source:50.0.0.50 (?), via Auto-RP
Uptime:00:03:04, expires:00:02:55
Info source:40.0.0.40 (?), via Auto-RP
Uptime:00:04:19, expires:00:02:38
(*, 225.1.3.0), 00:00:02/00:02:57, RP 3.3.3.3, flags:BC
Bidir-Upstream:GigabitEthernet2/1, RPF nbr 10.53.1.7, RPF-MFD
Outgoing interface list:
GigabitEthernet2/1, Bidir-Upstream/Sparse-Dense, 00:00:02/00:00:00,H
Vlan30, Forward/Sparse-Dense, 00:00:02/00:02:57, H
(*, 225.1.2.0), 00:00:04/00:02:55, RP 3.3.3.3, flags:BC
Bidir-Upstream:GigabitEthernet2/1, RPF nbr 10.53.1.7, RPF-MFD
Outgoing interface list:
GigabitEthernet2/1, Bidir-Upstream/Sparse-Dense, 00:00:04/00:00:00,H
Vlan30, Forward/Sparse-Dense, 00:00:04/00:02:55, H
(*, 225.1.4.1), 00:00:00/00:02:59, RP 3.3.3.3, flags:BC
Bidir-Upstream:GigabitEthernet2/1, RPF nbr 10.53.1.7, RPF-MFD
Outgoing interface list:
GigabitEthernet2/1, Bidir-Upstream/Sparse-Dense, 00:00:00/00:00:00,H
Vlan30, Forward/Sparse-Dense, 00:00:00/00:02:59, H
Cisco 7600 Series Router Cisco IOS Software Configuration Guide, Release 12.2SX
Purpose
Displays mappings between PIM groups and rendezvous
points and shows learned rendezvous points in use.
]
Displays PIM group to active rendezvous points mappings.
Displays information based on the group/mask ranges in the
RP mapping cache.
Displays information based on the DF list in RP mapping
cache.
Displays IPv4 bidirectional PIM information.
Displays information about the multicast routing table.
Configuring IPv4 Bidirectional PIM
28-25