Download Print this page

Service Information - HP D7171A - NetServer - LPr Reference Card

Hp netserver lc 2000 technical reference card
Hide thumbs Also See for D7171A - NetServer - LPr:

Advertisement

HP NetServer LC 2000 & LC 2000r Technical Reference Card
D
SCSI Hot-Swap HDD Configurations
HDD Slot
SCSI ID
6
9
8
5
8
4
3
2
3
2
2
1
0
1
0
6 LP
3 HH
1HH-4LP
HDD Slot
Hot-Swap Mass Storage
6
9
9
Configurations
5
8
• Ensure hot-swap drives are
3
4
installed in lowest (pedestal)
2
or left-most (rack) slot first.
3
2
2
• Use only HP Ultra-2 (LVD)
0
0
SCSI 3.5-inch HDDs.
1
• You may mix or match Low
Alternating
2HH-2LP
Profile (LP–1-inch) and Half-
HH-LP
Height (HH–1.6-inch) HHD.
• For rack-mounted models,
rotate diagrams 90˚ clockwise
Key
SCSI ID
Shown Here
F
Power Supply Cabling
System Board
C
Fan Module
Power Connector
Optional
Redundant Power
Supply Connectors
Mass Storage
Power Connector
E
9
9
8
8
3
2
2
1
0
0
2 LP-HH-2LP
1.6˝ Half-Height (HH) drive
1˝ Low Profile (LP) drive
.5˝ Drive Spacer
IDE CD-ROM Drive
Fan Module (Removed)
Non-Hot-Swap Mass
Storage Units
Flexible Disk Drive
P4
Front Panel
Display
P3
P5
P6
P
4
P
P2
5
P1
P
4
P
5
Mass Storage Cabling
1
2
3
4
5
Front Panel
Connector
IDE CD-ROM
Connector
SCSI B
Connector
SCSI A
Connector
Flexible
Disk Drive
Connector
System Board
C
Fan Module
(Removed)
G

Service Information

Electronic Support Services
• Internet Web Pages http://www.hp.com/netserver
• Internet FTP ftp://ftp.netserver.hp.com
• CompuServe Library GO HPPC
Hot-Swap Mass
• HP Navigator CD
Storage Drives
Support Questions
P1, P2, and P3 are
• HP-Authorized Reseller
connected to power
• CompuServe Discussion Forum GO HPPC
supplies below/behind
P4 and P5
• US / Canada Phone Support 1-208-331-2767
• Europe Phone Support (+31-20) 581-3330
P1
HP has offices in over 100 countries.
P4
Check your local telephone directory.
P2
P5
P3
HP Product No. D8514-80201, REV B, Sept. 1999
Cables
IDE CD-ROM Drive
1
FDD Cable
2
Unterminated SCSI Cable from
System Board to Hot-Swap Bay
Optional
(See Notes 1 & 2).
4
Non-Hot-
Swap Mass
Terminated SCSI Cable from System
3
3
Storage Units
Board to Common Tray Devices.
DO NOT CONNECT TO HOT-SWAP
3
Flexible Disk
BAY. (See Notes 1 & 2)
1
Drive
4
IDE CD-ROM Cable
5
Front Panel
Display
Control Panel Cable
5
2
SCSI Cable for Hot-Swap
6
Hot-Swap
6
Mass Storage
Drives
Note 1: Connectors on cables
6
Note 2: Cables
Mass Storage
Cage
Note 3: Further details in the
Audience Assumptions
This Technical Reference Card is for
trained service personnel. Hewlett-Packard
Company assumes you are qualified in the
servicing of computer equipment and trained
in recognizing hazards in products with
hazardous energy levels.
Electrostatic Discharge
To avoid catastrophic or hidden damage to
components, wear a wrist strap and use a
(Netherlands)
static-dissipative work surface connected to
the chassis when handling components. Use
an antistatic service kit, such as 3M
8501/8502/8505 or equivalent.
This information is subject to change without
notice and is provided without warranty.
© copyright 1999, Hewlett-Packard
For additional information, see other side.
Built-in SCSI Terminator
and
2
must be plugged into the
3
correct connector, as shown
on labeled cable-ends.
and
are not
2
3
interchangeable. Cable
is
2
unterminated, cable
is
3
terminated. Data corruption
will occur unless cables are
connected as shown.
Installation Guide.

Advertisement

loading