HP 8270 - ScanJet - Document Scanner Maintenance And Service Manual

Hp pavilion zd8000 notebook pc - maintenance and service guide.
Hide thumbs
Maintenance and Service
Guide
HP Pavilion zd8000 Notebook PC
Document Part Number: 372712-002
February 2008
This guide is a troubleshooting reference used for maintaining
and servicing the notebook. It provides comprehensive
information on identifying notebook features, components, and
spare parts; troubleshooting notebook problems; and performing
notebook disassembly procedures.

Advertising

   Also See for HP 8270 - ScanJet - Document Scanner

   Related Manuals for HP 8270 - ScanJet - Document Scanner

   Summary of Contents for HP 8270 - ScanJet - Document Scanner

  • Page 1

    Maintenance and Service Guide HP Pavilion zd8000 Notebook PC Document Part Number: 372712-002 February 2008 This guide is a troubleshooting reference used for maintaining and servicing the notebook. It provides comprehensive information on identifying notebook features, components, and spare parts; troubleshooting notebook problems; and performing notebook disassembly procedures.

  • Page 2

    Intel Corporation or its subsidiaries in the United States and other countries. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. SD logo is a trademark of its proprietor. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.

  • Page 3: Table Of Contents

    Contents 1 Product Description 1.1 Features ........1–2 1.2 Resetting the Notebook .

  • Page 4: Table Of Contents

    Contents 5 Removal and Replacement Procedures 5.1 Serial Number ......5–2 5.2 Disassembly Sequence Chart ....5–3 5.3 Preparing the Notebook for Disassembly .

  • Page 5: Product Description

    Product Description The HP Pavilion zd8000 Notebook PC offers advanced modularity, Intel® Mobile Pentium® 4 processors, and extensive multimedia support. HP Pavilion zd8000 Notebook PC Maintenance and Service Guide 1–1...

  • Page 6: Features

    Product Description 1.1 Features ■ The following processors are available, varying by notebook model: ❏ Intel Pentium 4 560 (3.6-GHz) with 800-MHz front side bus (FSB) with HT Technology ❏ Intel Pentium 4 550 (3.4-GHz) with 800-MHz FSB with HT Technology ❏...

  • Page 7

    Product Description ■ Integrated high-speed 56K modem with RJ-11 jack ■ Integrated wireless support for Mini PCI IEEE 802.11b and 802.11b/g WLAN device ■ Support for one Type II PC Card slot, with support for both 32-bit (CardBus) and 16-bit PC Cards ■...

  • Page 8: Resetting The Notebook, Power Management

    Product Description 1.2 Resetting the Notebook If the notebook you are servicing has an unknown password, follow these steps to clear the password. These steps also clear CMOS: 1. Prepare the notebook for disassembly (refer to Section 5.3, “Preparing the Notebook for Disassembly,” for more information).

  • Page 9: External Components

    Product Description 1.4 External Components The external components on the front of the notebook are shown below and described in Table 1-1. Front Components Table 1-1 Front Components Item Component Function Display release latch Opens the notebook. Stereo speakers (2) Produce stereo sound.

  • Page 10

    Product Description The external components on the right side of the notebook are shown below and described in Table 1-2. Right-Side Components Table 1-2 Right-Side Components Item Component Function Digital Media Slot Supports the following optional digital media: Secure Digital (SD) Memory Card, Secure Digital Input/Output (SD I/O), Memory Stick, Memory Stick Pro, MultiMediaCard, xD-Picture Card, and...

  • Page 11

    Product Description Table 1-2 Right-Side Components (Continued) Item Component Function Expansion port 2 Connects to an optional notebook expansion product. PC Card eject button Ejects an optional PC Card from the PC Card slot. PC Card slot Supports an optional Type I or Type II 32-bit (CardBus) or 16-bit PC Card.

  • Page 12

    Product Description The external components on the left side of the notebook are shown below and described in Table 1-3. Left-Side Components Table 1-3 Left-Side Components Item Component Function Exhaust vent Provides airflow to cool internal components. Ä To prevent overheating, do not obstruct vents.

  • Page 13

    Product Description The external components on the rear panel of the notebook are shown below and described in Table 1-4. Rear Panel Components Table 1-4 Rear Panel Components Item Component Function Security cable slot Attaches an optional security cable to the notebook.

  • Page 14

    Product Description The standard keyboard components of the notebook are shown below and described in Table 1-5. Standard Keyboard Components 1–10 Maintenance and Service Guide...

  • Page 15

    Product Description Table 1-5 Standard Keyboard Components Item Component Function caps lock key Enables caps lock and turns on the caps lock light. f1 to f12 keys (12) Perform system and application tasks. When combined with the fn key, several keys and buttons perform additional tasks as hotkeys.

  • Page 16

    Product Description The upper components of the keyboard are shown below and on the following page and described in Tables 1-6 and 1-7. Upper Keyboard Components 1–12 Maintenance and Service Guide...

  • Page 17

    Product Description Table 1-6 Upper Keyboard Components Item Component Function Power/standby button When the notebook is: ■ Off, press to turn on the notebook. ■ On, briefly press to initiate standby. ■ In standby, briefly press to resume from standby. ■...

  • Page 18

    Product Description The top components of the notebook are shown below and described in Table 1-7. Notebook Top Components 1–14 Maintenance and Service Guide...

  • Page 19

    Product Description Table 1-7 Notebook Top Components Item Component Function TouchPad Moves the pointer and selects or activates items on the screen. TouchPad light On: TouchPad is enabled. TouchPad button Enables/disables the TouchPad. Wireless button Turns the wireless network device on and off (select models only).

  • Page 20

    Product Description The external components on the bottom of the notebook are shown below and described in Table 1-8. Bottom Components Table 1-8 Bottom Components Item Component Function Exhaust vents (4) Provide airflow to cool internal components. Ä To prevent overheating, do not obstruct vents.

  • Page 21

    Product Description Table 1-8 Bottom Components (Continued) Item Component Function Fans (2) Provide airflow to cool internal components. Ä To prevent overheating, do not obstruct fans. Do not allow a hard surface, such as a printer, or a soft surface, such as pillows, thick rugs or clothing, to block airflow.

  • Page 22: Design Overview

    Product Description 1.5 Design Overview This section presents a design overview of key parts and features of the notebook. Refer to Chapter 3, “Illustrated Parts Catalog,” to identify replacement parts, and Chapter 5, “Removal and Replacement Procedures,” for disassembly steps. The system board provides the following device connections: ■...

  • Page 23: Computer Setup

    Troubleshooting WARNING: Only authorized technicians trained by HP should repair Å this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly-/module-level repair. Because of the complexity of the individual boards and subassemblies, do not attempt to make repairs at the component level or modifications to any printed wiring board.

  • Page 24

    Troubleshooting 2. Select the Main, Security, Advanced, or Tools menu. 3. To close Computer Setup and restart the notebook: ❏ Select Exit > Exit Saving Changes, and then press enter. – – ❏ Select Exit > Exit Discarding Changes, and then press enter.

  • Page 25

    Troubleshooting Selecting from the Security Menu Table 2-2 Security Menu Select To Do This Administrator Password Enter, change, or delete an Administrator password. Power-on Password Enter, change, or delete a power-on password. DriveLock Passwords Enable/disable DriveLock; change a DriveLock user or master password. ✎...

  • Page 26: Advanced Menu

    Troubleshooting Selecting from the Advanced Menu Table 2-3 Advanced Menu Select To Do This Language Change the Computer Setup language. Boot Order Enable/disable MultiBoot, which sets a startup sequence that can include most bootable devices and media in the system. Accessibility Options Allows electronic and information technology to be accessible to people with varying ranges of...

  • Page 27: Troubleshooting Flowcharts

    Troubleshooting 2.2 Troubleshooting Flowcharts Table 2-5 Troubleshooting Flowcharts Overview Flowchart Description “Flowchart 2.1—Initial Troubleshooting” “Flowchart 2.2—No Power, Part 1” “Flowchart 2.3—No Power, Part 2” “Flowchart 2.4—No Power, Part 3” “Flowchart 2.5—No Power, Part 4” “Flowchart 2.6—No Video, Part 1” “Flowchart 2.7—No Video, Part 2” “Flowchart 2.8—Nonfunctioning Expansion Base (if applicable)”...

  • Page 28

    Troubleshooting Table 2-5 Troubleshooting Flowcharts Overview (Continued) Flowchart Description 2.14 “Flowchart 2.14—No OS Loading, Optical Drive” 2.15 “Flowchart 2.15—No Audio, Part 1” 2.16 “Flowchart 2.16—No Audio, Part 2” 2.17 “Flowchart 2.17—Nonfunctioning Device” 2.18 “Flowchart 2.18—Nonfunctioning Keyboard” 2.19 “Flowchart 2.19—Nonfunctioning Pointing Device” 2.20 “Flowchart 2.20—No Network/Modem Connection”...

  • Page 29

    Troubleshooting Flowchart 2.1—Initial Troubleshooting Begin troubleshooting. Go to Is there “Flowchart power? 2.2—No Power, Part 1.” Check Beeps, LED board, LEDs, or error speaker messages? connections. Go to All drives “Flowchart working? 2.17—Nonfunction ing Device.” Go to Is there video? “Flowchart Go to (no boot)

  • Page 30

    Troubleshooting Flowchart 2.2—No Power, Part 1 No power (power LED is off). Remove from expansion base (if applicable). Go to Power up Power up Reset “Flowchart on battery on battery power.* 2.3—No Power, power? power? Part 2.” Go to Power up Power up Reset “Flowchart...

  • Page 31

    Troubleshooting Flowchart 2.3—No Power, Part 2 Continued from “Flowchart 2.2—No Power, Part 1.” Visually check for debris in battery socket and clean if necessary. Power on? Done Check battery by recharging it, moving it to another notebook, or replacing it. Replace Power on? power supply...

  • Page 32

    Troubleshooting Flowchart 2.4—No Power, Part 3 Continued from “Flowchart 2.3—No Power, Part 2.” Plug directly into AC outlet. Power LED Done Reseat AC adapter in notebook and at power source. Power on? Done External Internal or Replace external Try different Power outlet external AC AC adapter.

  • Page 33

    Troubleshooting Flowchart 2.5—No Power, Part 4 Continued from “Flowchart 2.4—No Power, Part 3.” Open notebook. Reseat loose Loose or components and damaged boards and parts? replace damaged items. Close notebook and retest. Replace the following items (if applicable). Power on? Check notebook operation after each replacement: 1.

  • Page 34

    Troubleshooting Flowchart 2.6—No Video, Part 1 No video. Expansion base Go to *NOTE: To change from internal to Stand-alone “Flowchart external display, use the hotkey or expansion 2.7—No Video, combination. base? Part 2.” Stand-alone Internal or Adjust Video OK? Done external brightness.

  • Page 35

    Troubleshooting Flowchart 2.7—No Video, Part 2 Continued from “Flowchart 2.6—No Video, Part 1.” Remove notebook from expansion base, if connected. Adjust Check brightness display of external brightness. monitor. Go to “A” in “Flowchart Video OK? Video OK? Done 2.6—No Video, Part 1.”...

  • Page 36

    Troubleshooting Flowchart 2.8—Nonfunctioning Expansion Base (if applicable) Nonfunctioning expansion base. Reseat power cord in expansion base and power outlet. Check voltage Reinstall setting on notebook into expansion base. expansion base. Reset monitor cable connector at Expansion expansion base. Done base operating? Expansion base...

  • Page 37

    Troubleshooting Flowchart 2.9—No Operating System (OS) Loading No OS loading.* Reseat power cord in expansion base and power outlet. No OS loading from hard drive, go to “Flowchart 2.10—No OS Loading, Hard Drive, Part 1.” No OS loading from diskette drive, go to “Flowchart 2.13—No OS Loading, Diskette Drive.”...

  • Page 38

    Troubleshooting Flowchart 2.10—No OS Loading, Hard Drive, Part 1 OS not loading from hard drive. Go to “Flowchart Nonsystem 2.11—No OS disk Loading, message? Hard Drive, Part 2.” Reseat external hard drive. OS loading? Done Boot from Go to Boot “Flowchart from 2.13—No OS...

  • Page 39

    Troubleshooting Flowchart 2.1 1—No OS Loading, Hard Drive, Part 2 Continued from “Flowchart 2.10—No OS Reseat Loading, hard drive. Hard Drive, Part 1.” 1. Replace CD or hard drive. diskette in 2. Replace drive? Hard drive system board. Done accessible? Remove diskette and Run FDISK.

  • Page 40

    Troubleshooting Flowchart 2.12—No OS Loading, Hard Drive, Part 3 Continued from “Flowchart 2.11—No OS Loading, Hard Drive, Part 2.” System Install OS files on hard and reboot. drive? Virus loading from Clean virus. Done hard drive? hard drive? Run SCANDISK Replace Diagnostics and check for...

  • Page 41

    Troubleshooting Flowchart 2.13—No OS Loading, Diskette Drive OS not loading Reseat Done from diskette drive. loading? diskette drive. Bootable Install bootable Nonsystem diskette diskette and disk message? in drive? reboot notebook. Check diskette for system files. Go to Boot Try different “Flowchart from another diskette.

  • Page 42

    Troubleshooting Flowchart 2.14—No OS Loading, Optical Drive No OS Install bootable Bootable Disc loading from disc and disc in in drive? CD-ROM or reboot drive? DVD-ROM drive. notebook. Install Try another bootable disc. bootable disc. Boots from Done CD or DVD? Boots from Reseat Done...

  • Page 43

    Troubleshooting Flowchart 2.15—No Audio, Part 1 Turn up audio internally or No audio. Audio? Done externally. Go to Notebook in Internal “Flowchart expansion base Undock audio? 2.16—No Audio, (if applicable)? Part 2.” Go to Replace the following expansion base components one at a time, as applicable. “Flowchart Check audio status after each change.

  • Page 44

    Troubleshooting Flowchart 2.16—No Audio, Part 2 Continued from “Flowchart 2.15—No Audio, Part 1.” Audio Reload driver in OS audio drivers. configured? Correct Load drivers and drivers for set configuration application? in OS. Connect to external speaker. Replace audio board and speaker Audio? Audio?

  • Page 45

    Troubleshooting Flowchart 2.17—Nonfunctioning Device Nonfunctioning device. Reseat device. Unplug the nonfunctioning device from the notebook and inspect cables and plugs for bent or broken pins or other damage. Fix or Clear Any physical replace CMOS. device detected? broken item. Go to “Flowchart Reattach device.

  • Page 46

    Troubleshooting Flowchart 2.18—Nonfunctioning Keyboard Keyboard not operating properly. Connect notebook to good external keyboard. External Replace device system works? board. Reseat internal keyboard connector (if applicable). Replace internal keyboard or cable. Done Done Replace system board. 2–24 Maintenance and Service Guide...

  • Page 47

    Troubleshooting Flowchart 2.19—Nonfunctioning Pointing Device Pointing device not operating properly. Connect notebook to good external pointing device. Replace External system device board. works? Reseat internal pointing device connector (if applicable). Replace internal pointing device or cable. Done Done Replace system board.

  • Page 48

    Troubleshooting Flowchart 2.20—No Network/Modem Connection No network or modem connection. Network Replace jack or modem or have jack jack active? activated. Connect Digital to nondigital line? line. Reload NIC/modem Done drivers and configured reconfigure. in OS? Disconnect all Replace power from NIC/modem the notebook (if applicable).

  • Page 49: Serial Number Location

    Illustrated Parts Catalog This chapter provides an illustrated parts breakdown and a reference for spare part numbers and option part numbers. 3.1 Serial Number Location When ordering parts or requesting information, provide the notebook serial number and model number located on the bottom of the notebook.

  • Page 50: Notebook Major Components

    Illustrated Parts Catalog 3.2 Notebook Major Components Notebook Major Components 3–2 Maintenance and Service Guide...

  • Page 51

    Illustrated Parts Catalog Table 3-1 Spare Parts: Notebook Major Components Spare Part Item Description Number Display assemblies (include wireless antenna boards and cables) 17.0-inch, WSXGA+WVA with Brightview 374723-001 17.0-inch, WXGA+WVA with Brightview 374722-001 17.0-inch, WXGA+WVA 374721-001 Switch cover For use on notebook models with wireless 374754-001 For use on notebook models without wireless 380444-001...

  • Page 52

    Illustrated Parts Catalog Notebook Major Components 3–4 Maintenance and Service Guide...

  • Page 53

    Illustrated Parts Catalog Table 3-1 Spare Parts: Notebook Major Components (Continued) Spare Part Item Description Number System boards (include disk cell RTC battery) M24P with 256 MB RAM 374711-001 M24P with 128 MB RAM 374709-001 M22P with 64 MB RAM 374707-001 Audio/USB board (includes cable) 374761-001...

  • Page 54

    Illustrated Parts Catalog Notebook Major Components 3–6 Maintenance and Service Guide...

  • Page 55

    Illustrated Parts Catalog Table 3-1 Spare Parts: Notebook Major Components (Continued) Spare Part Item Description Number Hard drives (include frame) 7200-rpm 4200-rpm 60-GB 374732-001 100-GB 374730-001 5400-rpm 80-GB 374729-001 100-GB 380258-001 60-GB 374728-001 80-GB 374731-001 40-GB 378767-001 Mini PCI communications cards 802.11b/g, for use in most of the world (MOW) 373047-001 802.11b/g, for use in the rest of the world (ROW)

  • Page 56: Miscellaneous Plastics Kit

    Illustrated Parts Catalog 3.3 Miscellaneous Plastics Kit Table 3-2 Spare Part Number 374746-001 Spare Part Item Description Number Hard drive cover (includes 4 captive screws) Memory module compartment cover (includes 2 captive screws) Notebook feet (7) SD Card slot space saver PC Card slot space saver 3–8 Maintenance and Service Guide...

  • Page 57: Mass Storage Devices

    Illustrated Parts Catalog 3.4 Mass Storage Devices Table 3-3 Spare Part Number Information Spare Part Item Description Number Optical drives Dual Format, Double Layer 382079-001 8X Dual Format, Light Scribe 383608-001 8X DVD±RW/R and CD-RW Combo Drive 374737-001 24X DVD/CD-RW Combo Drive 374735-001 Hard drives (include frame) 7200-rpm...

  • Page 58: Media Center Edition Accessories

    Illustrated Parts Catalog 3.5 Media Center Edition Accessories Table 3-4 Spare Part Number Information Spare Part Description Item Number Dual TV Tuner/Digital Video Recorder 377553-001 TV tuner stand 377559-001 TV tuner AC adapter 377555-001 Media Center mini remote control 375705-001 Not illustrated: Audio/Video Cable Kit 377557-001...

  • Page 59: Miscellaneous (not Illustrated)

    Illustrated Parts Catalog 3.6 Miscellaneous (Not Illustrated) Table 3-5 Spare Part Information Spare Part Description Number AC adapters 180 watt, 3-wire plug—for use on all notebook models 374743-001 135 watt, 3-wire plug—for use only on notebook models with 378768-001 Intel Pentium 4 530 (3.0-GHz) and Intel Pentium 4 520 (2.8-GHz) processors HP remote control 371694-001...

  • Page 60

    Illustrated Parts Catalog Table 3-5 Spare Part Information (Continued) Spare Part Description Number Power cords (3-wire plug, for use with 135-watt AC adapters) For use in: Australia and New Zealand 373979-011 Belgium, Europe, Finland, France, Germany, Greece, 373979-021 the Netherlands, Norway, Portugal, Spain, and Sweden Canada, French Canada, Latin America, Taiwan, Thailand, 373979-001 and the United States...

  • Page 61

    Illustrated Parts Catalog Table 3-5 Spare Part Information (Continued) Spare Part Description Number Power cords (3-wire plug, for use with 180-watt AC adapters) For use in: Australia and New Zealand 345252-011 Brazil 345252-201 Belgium, Europe, Finland, France, Germany, Greece, 345252-021 the Netherlands, Norway, Portugal, Spain, and Sweden Canada, French Canada, Latin America, Taiwan, Thailand, 345252-001...

  • Page 62: Sequential Part Number Listing

    Illustrated Parts Catalog 3.7 Sequential Part Number Listing Table 3-6 Sequential Part Number Listing Spare Part Number Description 309674-001 USB travel mouse 344897-001 USB 1.1 diskette drive 345252-001 Power cord, with 3-wire plug, for use with 180-watt AC adapters in Canada, French Canada, Latin America, Taiwan, Thailand, and the United States 345252-011 Power cord, with 3-wire plug, for use with 180-watt...

  • Page 63

    Illustrated Parts Catalog Table 3-6 Sequential Part Number Listing (Continued) Spare Part Number Description 345252-AA1 Power cord, with 3-wire plug, for use with 180-watt AC adapters in the People’s Republic of China 364727-001 USB digital drive 371693-001 Wired headset with volume control 371694-001 HP remote control 373047-001...

  • Page 64

    Illustrated Parts Catalog Table 3-6 Sequential Part Number Listing (Continued) Spare Part Number Description 373979-081 Power cord, with 3-wire plug, for use with 135-watt AC adapters in Denmark 373979-111 Power cord, with 3-wire plug, for use with 135-watt AC adapters in Switzerland 373979-AA1 Power cord, with 3-wire plug, for use with 135-watt AC adapters in the People’s Republic of China...

  • Page 65

    Illustrated Parts Catalog Table 3-6 Sequential Part Number Listing (Continued) Spare Part Number Description 374722-001 Display assembly, 17.0-inch, WXGA+WVA with Brightview, includes wireless antenna boards and cables 374723-001 Display assembly, 17.0-inch, WSXGA+WVA with Brightview, includes wireless antenna boards and cables 374724-001 256-MB memory module, 400 MHz DDR2 374725-001...

  • Page 66

    Illustrated Parts Catalog Table 3-6 Sequential Part Number Listing (Continued) Spare Part Number Description 374741-051 Keyboard for use in France 374741-061 Keyboard for use in Italy 374741-071 Keyboard for use in Spain 374741-081 Keyboard for use in Denmark 374741-091 Keyboard for use in Norway 374741-101 Keyboard for use in Sweden/Finland 374741-111...

  • Page 67

    Illustrated Parts Catalog Table 3-6 Sequential Part Number Listing (Continued) Spare Part Number Description 374752-001 Base enclosure 374754-001 Switch cover for use with notebook models with wireless 380030-001 Heat sink module (includes left fan and thermal paste) 374758-001 Modem board 374759-001 USB digital drive board 374760-001...

  • Page 68

    Illustrated Parts Catalog Table 3-6 Sequential Part Number Listing (Continued) Spare Part Number Description 377557-001 Dual Tuner Cable Kit 377558-001 Dual Tuner Miscellaneous Cable Kit 377559-001 Dual Tuner Plastic Stand 378521-001 Speakers, left and right 378767-001 4200-rpm, 40-GB hard drive, includes frame and connector 378768-001 AC adapters, 135 watt, 2-wire plug—for use only on notebook models with Intel Pentium 4 530 (3.0-GHz) and Intel Pentium 4...

  • Page 69: Tools Required

    Removal and Replacement Preliminaries This chapter provides essential information for proper and safe removal and replacement service. 4.1 Tools Required You will need the following tools to complete the removal and replacement procedures: ■ Magnetic screwdriver ■ Phillips P0 screwdriver ■...

  • Page 70: Service Considerations

    Removal and Replacement Preliminaries 4.2 Service Considerations The following sections include some of the considerations that you should keep in mind during disassembly and assembly procedures. ✎ As you remove each subassembly from the notebook, place the subassembly (and all accompanying screws) away from the work area to prevent damage.

  • Page 71: Preventing Damage To Removable Drives

    Removal and Replacement Preliminaries 4.3 Preventing Damage to Removable Drives Removable drives are fragile components that must be handled with care. To prevent damage to the notebook, damage to a removable drive, or loss of information, observe the following precautions: ■...

  • Page 72: Preventing Electrostatic Damage

    Removal and Replacement Preliminaries 4.4 Preventing Electrostatic Damage Many electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, the discharge contains enough power to alter device parameters or melt silicon junctions.

  • Page 73: Packaging And Transporting Precautions

    Removal and Replacement Preliminaries 4.5 Packaging and Transporting Precautions Use the following grounding precautions when packaging and transporting equipment: ■ To avoid hand contact, transport products in static-safe containers, such as tubes, bags, or boxes. ■ Protect all electrostatic-sensitive parts and assemblies with conductive or approved containers or packaging.

  • Page 74: Workstation Precautions

    Removal and Replacement Preliminaries 4.6 Workstation Precautions Use the following grounding precautions at workstations: ■ Cover the workstation with approved static-shielding material Table 4-2, "Static-Shielding Materials" (refer to ■ Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and equipment. ■...

  • Page 75: Grounding Equipment And Methods

    Removal and Replacement Preliminaries 4.7 Grounding Equipment and Methods Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ■ When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords.

  • Page 76

    Removal and Replacement Preliminaries Table 4-1 shows how humidity affects the electrostatic voltage levels generated by different activities. Table 4-1 Typical Electrostatic Voltage Levels Relative Humidity Event Walking across carpet 35,000 V 15,000 V 7,500 V Walking across vinyl floor 12,000 V 5,000 V 3,000 V...

  • Page 77: Removal And Replacement

    Removal and Replacement Procedures This chapter provides removal and replacement procedures. There are 69 screws and screw locks, in 9 different sizes, that must be removed, replaced, or loosened when servicing the notebook. Make special note of each screw size and location during removal and replacement.

  • Page 78: Serial Number

    Removal and Replacement Procedures 5.1 Serial Number Report the notebook serial number to HP when requesting information or ordering spare parts. The serial number is located on the bottom of the notebook. Serial Number Location 5–2 Maintenance and Service Guide...

  • Page 79: Disassembly Sequence Chart

    Removal and Replacement Procedures 5.2 Disassembly Sequence Chart Use the chart below to determine the section number to be referenced when removing notebook components. Disassembly Sequence Chart Section Description # of Screws Removed Preparing the notebook for disassembly Battery pack 4 to remove hard drive cover Hard drive 0 to remove hard drive...

  • Page 80

    Removal and Replacement Procedures Disassembly Sequence Chart (Continued) Section Description # of Screws Removed LED board 5.10 Keyboard 5.11 Display assembly 5.12 Top cover 5.13 Infrared board 5.14 Audio/USB board 5.15 Bluetooth board 5.16 System board 2 screw locks 7 screws 5.17 Speakers 2 on left speaker...

  • Page 81: Preparing The Notebook For Disassembly

    Removal and Replacement Procedures 5.3 Preparing the Notebook for Disassembly Before you begin any removal or installation procedures: 1. Shut down the notebook. If you are unsure whether the notebook is off or in hibernation, turn the computer on, and then shut it down through the operating system. 2.

  • Page 82

    Removal and Replacement Procedures b. Slide and hold the battery release latch 1 toward the front of the notebook. (The left edge of the battery pack disengages from the notebook.) c. Lift the right edge of the battery pack up and swing it to the left 2.

  • Page 83

    Removal and Replacement Procedures 5. Remove the hard drive by following these steps: a. Loosen the four PM2.0×5.0 screws 1 that secure the hard drive cover to the notebook. b. Remove the hard drive cover 2. ✎ The hard drive cover is included in the Miscellaneous Plastics Kit, spare part number 374746-001.

  • Page 84

    Removal and Replacement Procedures Hard Drive Spare Part Number Information 7200-rpm 60-GB 374732-001 5400-rpm 100-GB 380258-001 80-GB 374731-001 4200-rpm 100-GB 374730-001 80-GB 374729-001 60-GB 374728-001 40-GB 378767-001 5–8 Maintenance and Service Guide...

  • Page 85

    Removal and Replacement Procedures c. Grasp the mylar tab 1 on the left side of the hard drive and slide the hard drive to the left 2 to disconnect it from the system board. d. Remove the hard drive 3. Removing the Hard Drive Maintenance and Service Guide 5–9...

  • Page 86

    Removal and Replacement Procedures e. Remove the four PM2.5×4.0 screws 1 that secure the hard drive frame to the hard drive. f. Lift the frame straight up 2 to remove if from the hard drive. Removing the Hard Drive Frame and Connector Reverse the above procedure to install and reassemble the hard drive.

  • Page 87: Notebook Feet

    Removal and Replacement Procedures 5.4 Notebook Feet The notebook feet are adhesive-backed rubber pads. The feet are included in the Miscellaneous Plastics Kit, spare part number 374746-001. Replacing the Notebook Feet Maintenance and Service Guide 5–1 1...

  • Page 88: Optical Drive

    Removal and Replacement Procedures 5.5 Optical Drive Spare Part Number Information Dual Format, Double Layer 382079-001 8X Dual Format, Light Scribe 383608-001 8X DVD±RW/R and CD-RW Combo Drive 374737-001 24X DVD/CD-RW Combo Drive 374735-001 1. Prepare the notebook for disassembly (refer to Section 5.3).

  • Page 89

    Removal and Replacement Procedures 2. Remove the PM2.0×8.0 screw 1 that secures the optical drive to the notebook. 3. Insert a thin tool, such as a paper clip, into the media tray release hole 2. (The optical drive media tray releases from the optical drive.) 4.

  • Page 90: Memory Module

    Removal and Replacement Procedures 5.6 Memory Module Spare Part Number Information 1024-MB, 400 MHz DDR2 374726-001 512-MB, 400 MHz DDR2 374725-001 256-MB, 400 MHz DDR2 374724-001 1. Prepare the notebook for disassembly (refer to Section 5.3). 2. Loosen the PM2.0×5.0 screw 1 that secures the memory module compartment cover to the notebook.

  • Page 91

    Removal and Replacement Procedures 5. Spread the retaining tabs 1 on each side of the memory module socket to release the memory module board. (The back edge side of the board rises away from the notebook.) 6. Slide the module away from the socket at an angle 2. 7.

  • Page 92: Mini Pci Communications Card

    Removal and Replacement Procedures 5.7 Mini PCI Communications Card Spare Part Number Information 802.11b/g, for use in most of the world (MOW) 373047-001 802.11b/g, for use in the rest of the world (ROW) 373048-001 802.11a/b/g combination card, for use in the United States 376650-001 1.

  • Page 93

    Removal and Replacement Procedures 3. Disconnect the auxiliary and main 1 antenna cables from the Mini PCI communications card. ✎ Make note of which wireless antenna cable is attached to which antenna clip on the Mini PCI communications card before disconnecting the cables. 4.

  • Page 94: Switch Cover

    Removal and Replacement Procedures 5.8 Switch Cover Spare Part Number Information For use on notebook models with wireless 374754-001 For use on notebook models without wireless 380444-001 1. Prepare the notebook for disassembly (refer to Section 5.3). 2. Position the notebook with the rear panel toward you. 3.

  • Page 95

    Removal and Replacement Procedures 5. Turn the notebook display-side up with the front panel toward you. 6. Open the notebook as far as possible. 7. Lift up the left and right sides of the switch cover 1 to detach it from the notebook. 8.

  • Page 96: Led Board

    Removal and Replacement Procedures 5.9 LED Board Spare Part Number Information LED board (includes cable) 378771-001 1. Prepare the notebook for disassembly (refer to Section 5.3). 2. Remove the switch cover (refer to Section 5.8). 3. Release the zero insertion force (ZIF) connector 1 to which the LED board cable is connected and disconnect the cable.

  • Page 97

    Removal and Replacement Procedures 6. Slide the LED board to the right 1 until the tabs 2 on the top cover are aligned with the notches 3 on the LED board. 7. Remove the LED board 4. Removing the LED Board Reverse the above procedure to install the LED board.

  • Page 98: Keyboard

    Removal and Replacement Procedures 5.10 Keyboard Spare Part Number Information Belgium 374741-181 Portugal 374741-131 Denmark 374741-081 Saudi Arabia 374741-171 France 374741-051 Spain 374741-071 French Canada 374741-121 Sweden/Finland 374741-101 Germany 374741-041 Switzerland 374741-111 Greece 374741-151 United Kingdom 374741-031 International 374741-B31 Asia Pacific, Australia, 374741-001 Canada, 374741-061...

  • Page 99

    Removal and Replacement Procedures 4. Remove the two PM2.0×8.0 screws that secure the keyboard to the notebook. Removing the Keyboard Screws Maintenance and Service Guide 5–23...

  • Page 100

    Removal and Replacement Procedures 5. Turn the notebook display-side up with the front panel toward you. 6. Open the notebook as far as possible. 7. Use a flat-bladed tool to push back the four keyboard retention tabs. The tabs are located above the keys, above the keys, above the...

  • Page 101

    Removal and Replacement Procedures 9. Release the zero insertion force (ZIF) connector 1 to which the keyboard cable is connected and disconnect the keyboard cable 2 from the system board. 10. Remove the keyboard. Removing the Keyboard Reverse the above procedure to install the keyboard. Maintenance and Service Guide 5–25...

  • Page 102: Display Assembly

    Removal and Replacement Procedures 5.1 1 Display Assembly Spare Part Number Information 17.0-inch, WSXGA+WVA with Brightview 374723-001 17.0-inch, WXGA+WVA with Brightview 374722-001 17.0-inch, WXGA+WVA 374721-001 1. Prepare the notebook for disassembly (refer to Section 5.3) and remove the following components: a.

  • Page 103

    Removal and Replacement Procedures 2. Remove the wireless antenna cables from the top cover holes 1 and from the routing channels 2 through which the cables are routed. 3. Disconnect the display cable 3 from the system board. Disconnecting the Display Cables Maintenance and Service Guide 5–27...

  • Page 104

    Removal and Replacement Procedures 4. Remove the two PM2.0×8.0 screws that secure the display assembly to the notebook. Removing the Display Screws 5–28 Maintenance and Service Guide...

  • Page 105

    Removal and Replacement Procedures 5. Position the notebook with the rear panel toward you. CAUTION: Support the display assembly when removing the following Ä screws. Failure to support the display assembly can result in damage to the display assembly and other notebook components. 6.

  • Page 106: Top Cover

    Removal and Replacement Procedures 5.12 Top Cover Spare Part Number Information Top cover (includes TouchPad) 374750-001 1. Prepare the notebook for disassembly (refer to Section 5.3) and remove the following components: a. Optical drive (refer to Section 5.5) b. Memory module compartment (refer to Section 5.6) c.

  • Page 107

    Removal and Replacement Procedures 3. Remove the seven PM2.0×8.0 screws 1 on the surface of the base enclosure and the four PM2.0×8.0 screws 2 in the battery bay. Removing the Top Cover Screws, Part 1 4. Remove the two PM2.0×3.0 screws 1 in the optical drive bay and the four PM2.0×3.0 screws 2 on the rear edge of the base enclosure.

  • Page 108

    Removal and Replacement Procedures 5. Turn the notebook top-side up with the front panel toward you. 6. Release the ZIF connector 1 to which the TouchPad cable is connected and disconnect the TouchPad cable 2 from the system board. 7. Release the ZIF connector 3 to which the LED/button board cable is connected and disconnect the LED/button board cable 4 from the system board.

  • Page 109

    Removal and Replacement Procedures 9. Remove the three PM2.0×8.0 screws that secure the base enclosure to the notebook. Removing the Top Cover Screws 10. Swing the front edge of the top cover up and back 1 until it detaches from the notebook. 11.

  • Page 110: Infrared Board

    Removal and Replacement Procedures 5.13 Infrared Board Spare Part Number Information Infrared board with cable 374760-001 1. Prepare the notebook for disassembly (refer to Section 5.3) and remove the following components: a. Optical drive (refer to Section 5.5) b. Memory module compartment (refer to Section 5.6) c.

  • Page 111

    Removal and Replacement Procedures 2. Disconnect the infrared board cable 1 from the low insertion force (LIF) connector on the system board. 3. Remove the infrared board 2 from the clip in the base enclosure. Removing the Infrared Board Reverse the above procedure to install the infrared board. Maintenance and Service Guide 5–35...

  • Page 112: Audio/usb Board

    Removal and Replacement Procedures 5.14 Audio/USB Board Spare Part Number Information Audio/USB board (includes cable) 374761-001 1. Prepare the notebook for disassembly (refer to Section 5.3) and remove the following components: a. Optical drive (refer to Section 5.5) b. Memory module compartment (refer to Section 5.6) c.

  • Page 113

    Removal and Replacement Procedures 2. Disconnect the audio/USB board cable 1 from the system board. 3. Remove the PM2.0×6.0 screw 2 that secures the audio/USB board to the base enclosure. 4. Remove the audio/USB board cable from the base enclosure clips 3 through which it is routed.

  • Page 114: Bluetooth Board

    Removal and Replacement Procedures 5.15 Bluetooth Board Spare Part Number Information Broadcomm Bluetooth wireless card 376651-001 1. Prepare the notebook for disassembly (refer to Section 5.3) and remove the following components: a. Optical drive (refer to Section 5.5) b. Memory module compartment (refer to Section 5.6) c.

  • Page 115

    Removal and Replacement Procedures 2. Disconnect the Bluetooth board cable 1 from the system board. 3. Remove the Bluetooth board 2 from the clip in the base enclosure. Removing the Bluetooth Board Reverse the above procedure to install the Bluetooth board. Maintenance and Service Guide 5–39...

  • Page 116: System Board

    Removal and Replacement Procedures 5.16 System Board Spare Part Number Information M24P with 256 MB RAM (includes RTC battery) 374711-001 M24P with 128 MB RAM (includes RTC battery) 374709-001 M22P with 64 MB RAM (includes RTC battery) 374707-001 ✎ All system board spares kits include a disk cell RTC battery. ✎...

  • Page 117

    Removal and Replacement Procedures 3. Disconnect the fan cable from the system board through the memory module compartment. Disconnecting the Fan Cables 4. Turn the notebook top-side up with the front panel toward you. Maintenance and Service Guide 5–41...

  • Page 118

    Removal and Replacement Procedures 5. Disconnect the following cables from the system board: 1 Left speaker cable 2 Front panel LED board cable 3 Digital drive board cable 4 Right speaker cable 5 Audio/USB board cable Disconnecting the System Board Cables, Part 1 6.

  • Page 119

    Removal and Replacement Procedures 7. Position the notebook with the rear panel toward you. 8. Remove the following: 1 Two HM5.0×9.0 screw locks on each side of the external monitor connector 2 Five PM2.0×4.0 screws that secure the system board to the base enclosure 3 Two PM2.0×8.0 screws that secure the heat sink module to the base enclosure...

  • Page 120

    Removal and Replacement Procedures 9. Position the notebook with the front panel toward you. 10. Flex the right rear edge of the base enclosure outward until the expansion port 2 is clear of the base enclosure 1. 11. Lift the front edge of the system board until it clears the base enclosure 2.

  • Page 121: Speakers

    Removal and Replacement Procedures 5.17 Speakers Spare Part Number Information Left and right speakers 378521-001 1. Prepare the notebook for disassembly (refer to Section 5.3) and remove the following components: a. Optical drive (refer to Section 5.5) b. Memory module compartment cover (refer to Section 5.6) c.

  • Page 122

    Removal and Replacement Procedures 3. Remove the two PM2.0×4.0 1 screws that secure the left speaker to the base enclosure. 4. Remove the left speaker 2. Removing the Left Speaker 5–46 Maintenance and Service Guide...

  • Page 123

    Removal and Replacement Procedures 5. Remove the PM1.5×3.5 screw 1 that secures the right speaker to the base enclosure. 6. Lift the right side of the right speaker 2, then slide the speaker to the right to remove it 3. Removing the Right Speaker Reverse the above procedure to install the speakers.

  • Page 124: Usb Digital Drive Board

    Removal and Replacement Procedures 5.18 USB Digital Drive Board Spare Part Number Information USB digital drive board 374759-001 1. Prepare the notebook for disassembly (refer to Section 5.3) and remove the following components: a. Optical drive (refer to Section 5.5) b.

  • Page 125

    Removal and Replacement Procedures 2. Remove the two PM2.0×4.0 screws 1 that secure the digital drive board to the base enclosure. 3. Remove the digital drive board 2. Removing the Digital Drive Board Reverse the above procedure to install the digital drive board. Maintenance and Service Guide 5–49...

  • Page 126: Base Enclosure Fans

    Removal and Replacement Procedures 5.19 Base Enclosure Fans Spare Part Number Information Base enclosure middle fan 380029-001 Base enclosure right fan 380027-001 1. Prepare the notebook for disassembly (refer to Section 5.3) and remove the following components: a. Optical drive (refer to Section 5.5) b.

  • Page 127

    Removal and Replacement Procedures 2. Remove the two PM2.0×8.0 screws 1 that secure the middle fan to the base enclosure. 3. Remove the four PM2.0×8.0 screws 2 that secure the right fan to the base enclosure. 4. Remove the base enclosure middle 3 and right fans 4. Removing the Base Enclosure Fans Reverse the above procedure to install the base enclosure fans.

  • Page 128: Modem Board

    Removal and Replacement Procedures 5.20 Modem Board Spare Part Number Information Modem board 374758-001 1. Prepare the notebook for disassembly (refer to Section 5.3) and remove the following components: a. Optical drive (refer to Section 5.5) b. Memory module compartment cover (refer to Section 5.6) c.

  • Page 129

    Removal and Replacement Procedures 3. Remove the PM2.0×3.0 screw 1 that secures the modem board to the system board. 4. Remove the modem board 2. Removing the Modem Board Reverse the above procedure to install the modem board. Maintenance and Service Guide 5–53...

  • Page 130: Heat Sink Module

    Removal and Replacement Procedures 5.21 Heat Sink Module Spare Part Number Information Heat sink module (includes left fan and thermal paste) 380030-001 1. Prepare the notebook for disassembly (refer to Section 5.3) and remove the following components: a. Optical drive (refer to Section 5.5) b.

  • Page 131

    Removal and Replacement Procedures 2. Disconnect the fan cable from the system board 1. 3. According to the 1, 2, 3, 4 sequence stamped into the heat sink module, loosen the four PM2.0×12.0 spring-loaded shoulder screws 2 that secure the heat sink module to the system board.

  • Page 132: Processor

    Removal and Replacement Procedures 5.22 Processor Spare Part Number Information Intel Pentium 4 560 (3.6-GHz) 377213-001 Intel Pentium 4 550 (3.4-GHz) 374718-001 Intel Pentium 4 540 (3.2-GHz) 374717-001 Intel Pentium 4 530 (3.0-GHz) 374716-001 Intel Pentium 4 520 (2.8-GHz) 374715-001 1.

  • Page 133

    Removal and Replacement Procedures CAUTION: The processor release arm is under spring tension. Do not Ä let go of the arm when removing or installing the processor. Failure to follow this caution can result in damage to the processor and system board.

  • Page 134

    Removal and Replacement Procedures 4. Swing the processor socket cover up and forward 1. 5. Lift the processor straight up to remove it 2. ✎ The gold triangle 3 on the processor should be aligned in the front right corner when you install the processor. Removing the Processor Reverse the above procedure to install the processor.

  • Page 135: Specifications

    Specifications This chapter provides physical and performance specifications. Table 6-1 Notebook Dimensions Height Front 4.51 cm 1.78 in Rear 4.97 cm 1.96 in Width 39.79 cm 15.70 in Depth 28.81 cm 11.34 in Weight 4.22 kg 9.3 lb Stand-alone power requirements Operating voltage 19.0 V dc @ 7.1 A/9.5 A –...

  • Page 136

    Specifications Table 6-1 Notebook (Continued) Maximum altitude (unpressurized) Operating (14.7 to 10.1 psia) -15 m to 3,048 m -50 ft to 10,000 ft Nonoperating (14.7 to 4.4 psia) -15 m to 12,192 m -50 ft to 40,000 ft Shock Operating 125 g, 2 ms, half-sine 200 g, 2 ms, half-sine Nonoperating...

  • Page 137

    Specifications Table 6-2 17.0-inch, WSXGA+WVA Brightview Display Dimensions Height 23.00 cm 9.06 in Width 36.80 cm 14.49 in Diagonal 43.40 cm 17.09 in Number of colors Up to 16.8 million Contrast ratio 200:1 Brightness 180 nits typical Pixel resolution Pitch 0.197 ×...

  • Page 138

    Specifications Table 6-3 17.0-inch, WXGA+WVA Brightview Display Dimensions Height 23.00 cm 9.06 in Width 36.80 cm 14.49 in Diagonal 43.40 cm 17.09 in Number of colors Up to 16.8 million Contrast ratio 200:1 Brightness 180 nits typical Pixel resolution Pitch 0.259 ×...

  • Page 139

    Specifications Table 6-4 Hard Drives, Part 1 100-GB* 100-GB* 80-GB* 80-GB* Dimensions Height 9.5 mm 9.5 mm 9.5 mm 9.5 mm Width 70 mm 70 mm 70 mm 70 mm Weight 99 g 102 g 99 g 99 g Interface type ATA-5 ATA-5 ATA-5...

  • Page 140

    Specifications Table 6-5 Hard Drives, Part 2 60-GB* 60-GB* 40-GB* Dimensions Height 9.5 mm 9.5 mm 9.5 mm Width 70 mm 70 mm 70 mm Weight 102 g 99 g 99 g Interface type ATA-5 ATA-5 ATA-5 Transfer rate Synchronous (maximum) 100 MB/sec 100 MB/sec 100 MB/sec...

  • Page 141

    Specifications Table 6-6 Primary 12-cell, Li-Ion Battery Pack Dimensions Height 2.00 cm 0.79 in Width 15.80 cm 6.22 in Depth 11.90 cm 4.69 in Weight 0.34 kg 0.75 lb Energy Voltage 148. V Amp-hour capacity 6.6 Ah Watt-hour capacity 48 Wh Temperature Operating 5°C to 45°C...

  • Page 142

    Specifications Table 6-7 24X DVD/CD-RW Combo Drive Applicable disk Read: Write: DVD-R, DVD-RW, CD-R and CD-RW DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18), CD-ROM (Mode 1 and 2) CD Digital Audio CD-XA ready (Mode 2, Form 1 and 2) CD-I ready (Mode 2, Form 1 and 2) CD-R, CD-RW Photo CD (single and...

  • Page 143

    Specifications Table 6-7 24X DVD/CD-RW Combo Drive (Continued) Disk thickness 1.2 mm (0.047 in) Track pitch 0.74 µm Access time CD media DVD media Random < 110 ms < 130 ms Full stroke < 210 ms < 225 ms Audio output level Line-out, 0.7 V rms Cache buffer 2 MB...

  • Page 144

    Specifications Table 6-8 8X DVD±RW/R and CD-RW Combo Drive Applicable disk Read: Write: DVD-R, DVD-RW, CD-R and CD-RW DVD-ROM (DVD-5, DVD-R and DVD-9, DVD-10, DVD-RW DVD-18), CD-ROM (Mode 1 and 2) CD Digital Audio CD-XA ready (Mode 2, Form 1 and 2) CD-I ready (Mode 2, Form 1 and 2) CD-R, CD-RW...

  • Page 145

    Specifications Table 6-8 8X DVD±RW/R and CD-RW Combo Drive (Continued) Disk thickness 1.2 mm (0.047 in) Track pitch 0.74 µm Access time Random < 175 ms < 230 ms Full stroke < 285 ms < 335 ms Audio output level Audio-out, 0.7 Vrms Cache buffer 2 MB...

  • Page 146

    Specifications Table 6-9 System DMA Hardware DMA System Function DMA0 not applicable DMA1* not applicable DMA2* not applicable DMA3 not applicable DMA4 Direct memory access controller DMA5* Available for PC Card DMA6 Not assigned DMA7 Not assigned *PC Card controller can use DMA 1, 2, or 5. 6–12 Maintenance and Service Guide...

  • Page 147

    Specifications Table 6-10 System Interrupts Hardware IRQ System Function IRQ0 System timer IRQ1 Standard 101-/102-Key or Microsoft Natural Keyboard IRQ2 Cascaded IRQ3 Intel 82801DB/DBM USB2 Enhanced Host Controller—24CD IRQ4 COM1 IRQ5* Conexant AC—Link Audio Intel 82801DB/DBM SMBus Controller—24C3 Data Fax Modem with SmartCP IRQ6 Diskette drive IRQ7*...

  • Page 148

    Specifications Table 6-10 System Interrupts (Continued) Hardware IRQ System Function IRQ11 Intel USB EHCI controller—24CD Intel USB UHCI controller—24C4 Intel USB UHCI controller—24C7 Intel Pro/Wireless 2200BG TI OHCI 1394 host controller TI PCI1410 cardbus controller IRQ12 Synaptics PS/2 touch pad IRQ13 Numeric data processor IRQ14...

  • Page 149

    Specifications Table 6-11 System I/O Addresses I/O Address (hex) System Function (shipping configuration) 000 - 00F DMA controller no. 1 010 - 01F Unused 020 - 021 Interrupt controller no. 1 022 - 024 Opti chipset configuration registers 025 - 03F Unused 02E - 02F 87334 “Super I/O”...

  • Page 150

    Specifications Table 6-11 System I/O Addresses (Continued) I/O Address (hex) System Function (shipping configuration) 0A2 - 0BF Unused 0C0 - 0DF DMA controller no. 2 0E0 - 0EF Unused 0F0 - 0F1 Coprocessor busy clear/reset 0F2 - 0FF Unused 100 - 16F Unused 170 - 177 Secondary fixed disk controller...

  • Page 151

    Specifications Table 6-11 System I/O Addresses (Continued) I/O Address (hex) System Function (shipping configuration) 2F0 - 2F7 Unused 2F8 - 2FF Infrared port 300 - 31F Unused 320 - 36F Unused 370 - 377 Secondary diskette drive controller 378 - 37F Parallel port (LPT1/default) 380 - 387 Unused...

  • Page 152

    Specifications Table 6-12 System Memory Map Size Memory Address System Function 640 KB 00000000-0009FFFF Base memory 128 KB 000A0000-000BFFFF Video memory 48 KB 000C0000-000CBFFF Video BIOS 160 KB 000C8000-000E7FFF Unused 64 KB 000E8000-000FFFFF System BIOS 15 MB 00100000-00FFFFFF Extended memory 58 MB 01000000-047FFFFF Super extended memory...

  • Page 153

    Connector Pin Assignments Table A-1 Universal Serial Bus Signal Signal +5 VDC Data + Data – Ground Maintenance and Service Guide A–1...

  • Page 154

    Connector Pin Assignments Table A-2 RJ-45 (Network) Signal Signal Transmit + Unused Transmit – Receive – Receive + Unused Unused Unused Table A-3 S-Video-Out 4 56 Signal Signal S-VHS color (C) signal TV-CD Composite video signal S-VHS intensity ground S-VHS intensity (Y) signal Composite video ground S-VHS color ground A–2...

  • Page 155

    Connector Pin Assignments Table A-4 External Monitor Signal Signal Red analog +5 VDC Green analog Ground Blue analog Monitor detect Not connected DDC 2B data Ground Horizontal sync Ground analog Vertical sync Ground analog DDC 2B clock Ground analog Maintenance and Service Guide A–3...

  • Page 156

    Connector Pin Assignments Table A-5 RJ-11 (Modem) Signal Signal Unused Unused Unused Ring Unused A–4 Maintenance and Service Guide...

  • Page 157

    Connector Pin Assignments Table A-6 Audio-In (Microphone) Signal Signal Audio signal in Ground Audio signal in Maintenance and Service Guide A–5...

  • Page 158

    Connector Pin Assignments Table A-7 Audio-Out (Headphone) Signal Signal Audio out, left channel Ground Audio out, right channel A–6 Maintenance and Service Guide...

  • Page 159

    Power Cord Set Requirements 3-Conductor Power Cord Set The wide range input feature of the notebook permits it to operate from any line voltage from 100 to 120 or 220 to 240 volts AC. The power cord set included with the notebook meets the requirements for use in the country where the equipment is purchased.

  • Page 160: General Requirements

    Power Cord Set Requirements General Requirements The requirements listed below are applicable to all countries. ■ The length of the power cord set must be at least 1.5 m (5.0 ft) and a maximum of 2.0 m (6.5 ft). ■ All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the country where the power cord set will be used.

  • Page 161

    Power Cord Set Requirements Country-Specific Requirements 3-Conductor Power Cord Set Requirements Country Accredited Agency Applicable Note Number Australia EANSW Austria Belgium CEBC Canada Denmark DEMKO Finland FIMKO France Germany Italy Japan METI The Netherlands KEMA Norway NEMKO Sweden SEMKO Switzerland Maintenance and Service Guide B–3...

  • Page 162

    Power Cord Set Requirements 3-Conductor Power Cord Set Requirements (Continued) Country Accredited Agency Applicable Note Number United Kingdom United States NOTES: 1. The flexible cord must be <HAR> Type HO5VV-F, 3-conductor, 1.0 mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country where it will be used.

  • Page 163

    Screw Listing This appendix provides specification and reference information for the screws used in the notebook. All screws listed in this appendix are available in the Miscellaneous Screw Kit, spare part number 374744-001. Maintenance and Service Guide C–1...

  • Page 164

    Screw Listing Table C-1 Phillips PM2.0×5.0 Screw Head Color Qty. Length Thread Width Black 5.0 mm 2.0 mm 4.0 mm Where used: Four screws that secure the hard drive cover to the notebook (screws are captured on the cover by C clips; documented in Section 5.3) One screw that secures the memory module compartment cover to the...

  • Page 165

    Screw Listing Table C-2 Phillips PM2.5×4.0 Screw Head Color Qty. Length Thread Width Silver 4.0 mm 2.5 mm 4.0 mm Where used: Four screws that secure the hard drive frame to the hard drive (documented in Section 5.3) Phillips M2.5×4.0 Screw Locations Maintenance and Service Guide C–3...

  • Page 166

    Screw Listing Table C-3 Phillips PM2.0×8.0 Screw Head Color Qty. Length Thread Width Black 8.0 mm 2.0 mm 4.0 mm Where used: One screw that secures the optical drive to the notebook (documented in Section 5.5) Five screws that secure the switch cover to the notebook (documented in Section 5.8)

  • Page 167

    Screw Listing Table C-3 Phillips PM2.0×8.0 Screw (Continued) Head Color Qty. Length Thread Width Black 8.0 mm 2.0 mm 4.0 mm Where used: Two screws that secure the display assembly to the notebook (documented in Section 5.11) Three screws that secure the top cover to the notebook (documented in Section 5.12)

  • Page 168

    Screw Listing Table C-3 Phillips PM2.0×8.0 Screw (Continued) Head Color Qty. Length Thread Width Black 8.0 mm 2.0 mm 4.0 mm Where used: Two screws that secure the display assembly to the notebook (documented in Section 5.11) Phillips M2.0×8.0 Screw Locations C–6 Maintenance and Service Guide...

  • Page 169

    Screw Listing Table C-3 Phillips PM2.0×8.0 Screw (Continued) Head Color Qty. Length Thread Width Black 8.0 mm 2.0 mm 4.0 mm Where used: Eleven screws that secure the top cover to the notebook (documented in Section 5.12) Phillips M2.0×8.0 Screw Locations Maintenance and Service Guide C–7...

  • Page 170

    Screw Listing Table C-3 Phillips PM2.0×8.0 Screw (Continued) Head Color Qty. Length Thread Width Black 8.0 mm 2.0 mm 4.0 mm Where used: Two screws that secure the heat sink module to the notebook (documented in Section 5.21) Phillips M2.0×8.0 Screw Locations C–8 Maintenance and Service Guide...

  • Page 171

    Screw Listing Table C-3 Phillips PM2.0×8.0 Screw (Continued) Head Color Qty. Length Thread Width Black 8.0 mm 2.0 mm 4.0 mm Where used: One screw that secures the left speaker to the notebook (documented in Section 5.17) Phillips M2.0×8.0 Screw Location Maintenance and Service Guide C–9...

  • Page 172

    Screw Listing Table C-3 Phillips PM2.0×8.0 Screw (Continued) Head Color Qty. Length Thread Width Black 8.0 mm 2.0 mm 4.0 mm Where used: Two screws that secure the base enclosure left fan to the notebook (documented in Section 5.19) Four screws that secure the base enclosure right fan to the notebook (documented in Section 5.19)

  • Page 173

    Screw Listing Table C-4 Phillips PM2.0×3.0 Screw Head Color Qty. Length Thread Width Black 3.0 mm 2.0 mm 4.0 mm Where used: Six screws that secure the top cover to the notebook (documented in Section 5.12) Phillips M2.0×3.0 Screw Locations Maintenance and Service Guide C–1 1...

  • Page 174

    Screw Listing Table C-4 Phillips PM2.0×3.0 Screw (Continued) Head Color Qty. Length Thread Width Black 3.0 mm 2.0 mm 4.0 mm Where used: One screw that secures the modem board to the notebook (documented in Section 5.20) Phillips M2.0×3.0 Screw Location C–12 Maintenance and Service Guide...

  • Page 175

    Screw Listing Table C-5 Phillips PM2.0×6.0 Screw Head Color Qty. Length Thread Width Black 6.0 mm 2.0 mm 4.0 mm Where used: One screw that secures the audio/USB board to the notebook (documented in Section 5.14) Phillips M2.0×6.0 Screw Location Maintenance and Service Guide C–13...

  • Page 176

    Screw Listing Table C-6 Hex Socket HM5.0×9.0 Screw Lock Head Color Qty. Length Thread Width Silver 9.0 mm 2.5 mm 5.0 mm Where used: Two screw locks that secure the system board to the notebook (documented in Section 5.16) Hex Socket HM5.0×9.0 Screw Lock Locations C–14 Maintenance and Service Guide...

  • Page 177

    Screw Listing Table C-7 Phillips PM2.0×4.0 Screw Head Color Qty. Length Thread Width Silver 4.0 mm 2.0 mm 4.0 mm Where used: One screw that secures the LED board to the notebook (documented in Section 5.9) Phillips M2.0×4.0 Screw Locations Maintenance and Service Guide C–15...

  • Page 178

    Screw Listing Table C-7 Phillips PM2.0×4.0 Screw (Continued) Head Color Qty. Length Thread Width Silver 4.0 mm 2.0 mm 4.0 mm Where used: Five screws that secure the system board to the notebook (documented in Section 5.16) Phillips M2.0×4.0 Screw Locations C–16 Maintenance and Service Guide...

  • Page 179

    Screw Listing Table C-7 Phillips PM2.0×4.0 Screw (Continued) Head Color Qty. Length Thread Width Silver 4.0 mm 2.0 mm 4.0 mm Where used: Two screws that secure the left speaker to the notebook (documented in Section 5.17) Phillips M2.0×3.0 Screw Location Maintenance and Service Guide C–17...

  • Page 180

    Screw Listing Table C-7 Phillips PM2.0×4.0 Screw (Continued) Head Color Qty. Length Thread Width Silver 4.0 mm 2.0 mm 4.0 mm Where used: Two screws that secure the digital drive board to the notebook (documented in Section 5.18) Phillips M2.0×4.0 Screw Locations C–18 Maintenance and Service Guide...

  • Page 181

    Screw Listing Table C-8 Phillips PM1.5×3.5 Screw Head Color Qty. Length Thread Width Silver 3.5 mm 1.5 mm 3.5 mm Where used: One screw that secures the right speaker to the notebook (documented in Section 5.17) Phillips M1.5×3.5 Screw Location Maintenance and Service Guide C–19...

  • Page 182

    Screw Listing Table C-9 Phillips PM2.0×12.0 Spring-Loaded Shoulder Screw Head Color Qty. Length Thread Width Silver 12.0 mm 2.0 mm 6.0 mm Where used: Four screws that secure the heat sink module to the notebook (documented in Section 5.21) Phillips M2.0×12.0 Spring-Loaded Shoulder Screw Locations C–20 Maintenance and Service Guide...

  • Page 183

    Index 1394 port 1–6 spare part number 3–7 3–19 5–5 specifications 6–7 AC adapter, spare part battery pack release latch 1–17 numbers 3–11 3–18 3–20 Bluetooth board AC power light 1–5 removal 5–38 arrow keys 1–11 spare part number 3–3 audio troubleshooting 2–21 5–38 audio/USB board...

  • Page 184

    Index right-side 1–6 diskette drive, USB, spare part upper keyboard 1–12 number 3–14 Computer Setup display assembly Advanced Menu 2–4 removal 5–26 5–48 5–50 Main Menu 2–2 5–52 overview 2–1 spare part numbers 3–3 Security Menu 2–3 3–16 3–17 5–26 5–48 Tools Menu 2–4 5–50...

  • Page 185

    Index spare part number 3–5 no audio 2–21 2–22 3–9 3–17 5–12 no network/modem specifications 6–8 connection 2–26 DVD±RW/R and CD-RW no OS loading 2–15 Combo Drive no OS loading from removal 5–12 CD-ROM/DVD-ROM spare part number 3–5 Drive 2–20 3–9 3–17 5–12...

  • Page 186

    Index hard drive activity light 1–5 LED board hard drive bay 1–17 removal 5–20 hard drive cover spare part number 3–3 removal 5–7 3–20 5–20 headphone jack left-side components 1–8 location 1–8 Logo Kit, spare part number pin assignments A–6 3–11 3–18 headset, spare part number...

  • Page 187

    Index Miscellaneous Cable Kit, spare part number 3–10 operating system not loading, Miscellaneous Plastics Kit troubleshooting 2–15 components 3–7 3–8 optical drive spare part number 3–7 location 1–8 3–18 OS not loading 2–20 Miscellaneous Screw Kit, removal 5–12 spare part number 3–18 spare part number 3–5 modem board 3–20...

  • Page 188

    Index hard drive 6–5 6–6 I/O addresses 6–15 rear components 1–8 interrupts 6–13 remote control, spare part memory map 6–18 number 3–11 3–15 notebook 6–1 removal and replacement static shielding materials 4–8 preliminaries 4–1 S-Video-out jack removal and replacement location 1–9 procedures 5–1 pin assignments A–2 right-side components 1–6...

  • Page 189

    Index flowcharts 2–5 keyboard 2–24 video troubleshooting 2–12 modem 2–26 volume buttons 1–13 network 2–26 nonfunctioning device Windows applications key 2–14 2–23 1–11 OS not loading 2–15 Windows logo key 1–11 overview 2–1 wireless button 1–15 pointing device 2–25 wireless light 1–15 power 2–8 workstation precautions 4–6 video 2–12...

Comments to this Manuals

Symbols: 0
Latest comments: