Download  Print this page

Kenwood KTF-2010 Instruction Manual page 10

Fm/mw/lw tuner
Hide thumbs

Advertisement

Storing broadcast stations in memory
10
The automatic memory function allows you to store up to
40 stations using only one button.
The manual preset function allows you to store stations
one at a time.
Use the automatic memory function first.
AUTO MEMORY (Storing stations automatically in memory )
The AUTO MEMORY function automatically calls up only those stations which have RDS broadcasts for storing
(up to 40 stations can be stored).
1 Switch to FM band.
2 Press and hold the MEMORY key (for more than 2 seconds).
MANUAL PRESET(Storing stations one at a time)
1
Tune in the station to be preset
2
Press the MEMORY key
If you press the MEMORY key when the preset number dis-
- -
played is "
", the smallest unstored number appears.
3
Select one of the preset numbers from 1 to 40.
1 Turn the TUNING/MULTI CONTROL knob.
2 Select the desired station.
Instead of steps 1 and 2, you can use the numeric keys
(0~9,+10), to store the broadcast stations.
Press the numeric keys (0 to 9, +10) in the
following order.
To select "15"...0,5
To select "20"...0,0, )
MEMORY
MEMORY
TUNING/MULTI CONTROL
DOWN
UP
MEMORY
The figure shows an example for the KTF-3010
AM-FM STEREO SYNTHESIZER TUNER KTF-3010
HIGHBLEND
WIDE
NARROW
ACTIVE
RECEPTION
IF BAND
RF ATT
ANT A/B
RFATT
PTY/
MEMORY
TA/NEWS
PTY SCARCH
DISPLAY
ON/STANDBY
1
2
3
4
: Keys or controls to be used in this operation.
The tuner completes the scanning of frequencies in 5 minutes.
While scanning, "AUTO" and "MEMORY" are displayed in turn.
÷ Unless stations are stored with the automatic memory function, EON
reservation and PTY search will not work.
÷ AR will not work when the automatic memory function is on.
÷ Broadcast stations stored manually may be overwritten.
÷ Stations already stored in the preset memory may be replaced by RDS
stations. (i.e., If the RDS AUTO MEMORY function finds 15 RDS sta-
tions, the stations currently preset at numbers 01- 15 are replaced by
the RDS stations.)
÷ If the antenna is replaced, you will have to reset the automatic memory
function.
÷ Stored stations may be erased from the memory.
Perform the operations in the five seconds that the display is blinking.
STANDBY
AR
0
1
AM
FM
(If more than 5 sec. have elapsed, press the MEMORY key again.)
Blinks
Lights (for 5 sec.)
AR
1
5
FM
The numbers 1 to 40 appear, in turn, as you turn the knob.
01
,
02
,
03
÷ Repeat steps 1 to 3 for each of the stations to be stored in memory.
÷ If a station is stored in a preset number which already stores a station
memory under it, the previous memory is replaced by the new memory
content.
÷ Once the memory content has been preset, it is held for about 3 days
even after the power cord is unplugged from the mains outlet.
÷ You cannot enter numbers over 40.
÷ If you make a mistake when pressing the 0 key, press the 0
key several times to return to the original display before re-entering.
÷ The stored station will be erased from the memory.
KTF-3010/KTF-2010 (En)
TUNING/MULTI CONTROL
BAND
TUNING MODE +10/CLEAR
P. CALL
DOWN
UP
5
6
7
8
9
0/CHARA.
Lights (for 5 sec.)
MEMO
ANT A
B
STEREO
TUNED
8 9 ) )
AUTO
kHz
MHz
MEMO
ANT A
STEREO
TUNED
9 ) ) )
.
AUTO
MHz
38
,
39
,
40

Advertisement

loading

  Related Manuals for Kenwood KTF-2010

This manual is also suitable for:

Ktf-3010