Chapter Three: Setting Up On The Receiver; Speaker Setup - Kenwood KRF-X9995D Connection And Setup Manual

Digital audio/video receiver
Hide thumbs Also See for KRF-X9995D:
Table of Contents

Advertisement

Chapter Tree: Setting Up on the Receiver
It is possible to set up the speakers on the receiver main
unit.
However, some of the setting items such as the controlled
device registration should be set on the PowerTouch. If
setup is made on the PowerTouch, it is not necessary to
repeat any setup on the receiver side.
Therefore, it is recommended to perform setup on the
PowerTouch. This chapter describes the setup on the receiver
only as an alternative method in case the setup is not made
on the PowerTouch.
Do not operate the PowerTouch during the receiver setup.
Preparation for setup
Most of the receiver control buttons are accommodated
inside the panel door. Make the following preparation for
setup on the receiver.
1. Plug the power cord into a household power outlet.
46
2. Press the POWER switch to supply the main power. The
receiver now enters the STANDBY mode (in which re-
mote control is available). Then press the ON/STANDBY
button to turn the receiver ON.
3. Open the panel door.
Panel door
Chapter Tree: Setting Up on the Receiver
Button layout

Speaker Setup

1. Selecting the speakers
Selecting the SUBWOOFER:
1 Press the SET UP button (SOUND button) inside
the panel door until "SUBWOOFER OFF (or ON)"
message appears on the display ( for more than 2
seconds ).
2 Press the MULTI CONTROL (fi/%) button to select
ON (when a subwoofer is used) or OFF (when not).
Selecting the FRONT speakers:
3 Press the SET UP button to display "FRONT NML/
THX (or FRONT LARGE)".
4 Press the MULTI CONTROL (fi/%) button to select
FRONT LARGE (large-sized speakers) or NML/THX
(normal-sized speakers).
If the SUBWOOFER is set to OFF, the FRONT speak-
ers are set automatically to LARGE and the CENTER
speaker selection display appears automatically.
Press the DOOR OPEN/
Selecting the CENTER speaker:
CLOSE button to open
5 Press the SET UP button to display "CENTER NML/
the panel door. To close
it, press the button again.
THX (or LARGE or OFF)".
6 Press the MULTI CONTROL (fi/%) button to select
CENTER LARGE (large-sized speaker), NML/THX
(normal-sized speaker) or OFF (no center speaker).
If the FRONT is set to NML/THX, the CENTER
speaker can be set to only either NML/THX or OFF.
Selecting the SURROUND speakers:
7 Press the SET UP button to display "SURR NML/
INPUT
CD 2/TAPE 2
LISTEN
A
SPEAKERS
B
MODE
MONITOR
MODE
THX
SOUND
DISPLAY
SET UP
%
%
MULTI
P.CALL
MEMORY
AUTO
BAND
CONTROL
THX (or LARGE or OFF)".
8 Press the MULTI CONTROL (fi/%) button to select
SURR LARGE (large-sized speakers), NML/THX
(normal-sized speakers) or OFF (no surround
speaker).
When the FRONT is set to NML/THX, the SUR-
ROUND speakers can be set to only either NML/THX
or OFF.
When SURROUND OFF is selected, SURROUND
BACK is set automatically to OFF and the SW Re-
Mix setting menu is displayed.
If the SUBWOOFER is set to OFF, selecting SW RE-
MIX step will be skipped.
Selecting the SURROUND BACK speakers:
9 Press the SET UP button to display "S.BACK NML/
THX (or LARGE or OFF)".
0 Press the MULTI CONTROL (fi/%) button to select
S. BACK LARGE (large-sized speakers), NML/THX
(normal-sized or THX speakers) or OFF (no surround
speaker).
When the FRONT is set to NML/THX, the SUR-
ROUND BACK speakers can be set to only either
NML/THX or OFF.

Advertisement

Table of Contents
loading

Table of Contents