LG 26LH1DC1 Installation And Operating Manual page 67

Procedures for adding Channel Label Icons/Custom Channel Labels
(2-5-4 + MENU Mode)
Adding Channel Icons and Labels in the 2-5-4 + Menu Mode
Editing/Adding Channel ICONs and/or Labels
If there is no pre-assigned ICON, you can make a
channel label of up to 7 characters to help in identifying
the channel or network.
At your option, channel labels can also be added in
addition to a preassigned ICON. You may also add
labels for the Aux input sources to clearly identify the
devices that are connected to the Aux inputs.
(Icon)
I LF1R RRRFI NETWORK
I II II II II II II I (Label)
1234567
Editing and adding the labels can only be done if there
are channels entered into the 26LH1DC1's channel map
either by using the method described in item 6 (page
67), by cloning or by the use of the master remote
control from the PPV provider.
To Do Channel Editing/Labeling, proceed as follows
I. Enter 26LHIDC1 Installer menu.
2. After the installer menu appears, press '2', '5', '4',
'MENU'.
This enters the channel label edit mode.
Add your channel icons and channel labels in this
menu, see below. (You can do this more than once.)
3. To exit the menu when done press "MENU".
Changing a Channel's ICON on
Master TV
1. With Channel Up/Down, select
the channel you want to change
the Icon for.
2. With the Right or Left ADJ
button, select the letter T on the
channel ID display.
3. With the Up or Down ADJ button,
select the desired ICON you
want to appear to identify the
channel. (If you know the ICON
number, enter the number
followed by Enter / Select.)
*Note: If no Icon is available,leaveat or
select the default blank icon display.
4. Proceed with Changing/Adding
Labels orgo to the next channel.
Changing/Adding Channel Labels
on Master TV
1. Channel Up/Down to select the
desired channel.
2. Press the Right or Left ADJ arrow
repeatedly until the numbers 1 to
7 show up. The number shows
the position of the character that
can be changed. Number 1 is the
first character, number 2 the sec-
ond character and so on.
3. With the Up or Down ADJ arrow,
select the desired character.
4. Proceed to the next number posi-
tion or use Channel Up/Down to
go to the next channel.
Changing Source Labels on Master
TV
1. Press "TV/AV" to select the
desired Aux input source; Video 1,
Component, S-Video etc.
2. Press the Right or Left ADJ arrow
repeat-edly until the numbers 0
to 9 show up.
The number shows the position of
the character that can be
changed.
3. Use the Up or Down ADJ arrow
to select the desired character.
4. Press "TV/AV" for the next Aux
source or proceed with Changing
Icon or Changing/Adding Labels.
N
0
I'rl
N
J
r"
0
I'rl
Installer Remote Control Key Functions for Master TV Channel Editing/Labeling Menu
• CHANNEL Up/Down - Tunes in the next channel in
scan.
• Left/Right Arrows - Select the item to change. If"l"
is shown, the ICON can be changed. If a number is
shown, it indicates the position of the character that
can be changed.
• Up/Down Arrows - Select the ICON or the character
to be displayed.
• 0 - 9 - Use to enter the index number of the ICON,
if known.
• OK (Enter/Select) - Changes the ICON after the
number has been entered.
• TV/AV - Changes the Aux input label. This key is
located on side of set and on Installer remote control.
• MENU - Exits the labeling/editing menu.
67