LG 26LH1DC1 Installation And Operating Manual page 65

Detailed Descriptions of Installer Menu Items
079 - UPN MSB-1 (UPN Most Significant Byte-1 )
User programmable numben most significant byte-1
readable by M.RI. command. Not linked to serial number.
080 - UPN MSB-2 (UPN Most Significant Byte-2)
User programmable numben most significant byte-2
readable by M.RI. command. Not linked to serial number.
081 - UPN LSB (UPN Least Significant Byte)
User programmable numben least significant byte
readable by M.RI. command. Not linked to serial number.
082 - CHASM ERROR (Checksum Error)
Enforces rigid M.RI. checksum validation.
Set to 1 for validation.
Set to 0 to disable (does not check checksum on M.RI.
async port).
SPI is always checked.
083 - HANDSHK TIME (Handshake Time)
Adds an additional delay to the handshake time which is
64 msec, thus relaxing M.RI. timing requirements to be
compatible with PC based Windows controlled systems,
range is 0 - 5.
(Timeout = 25.5MS + [25.5 MS* Handshake time]).
084 - PERMANENT BLK (Permanent Block)
Allows Lock (Parental Control) blocking schemes to be
permanent by disabling the blocking hours function.
Set to 1 to install Parental Control restrictions
permanently.
Set to 0 for user-specified hours control of blocking
schemes.
087 - REAR RGB EN. (Rear RGB1 Enable)
Controls access to rear RGB1 input on display panel.
Set to 1 to enable RGB1 input for DTV. Set to 0 to
disable RGB1 input.
*Note: The setting above is ignored if Installer item 093 RJP
AVAILABLE, is set to 1. Then 087 - REAR RGB EN. above, always
resets itself to PC (1) -- regardless of what value appears for item
087 on the Installer menu.
088 - EN NOISE MUTE (Enable Noise Mute)
If set to 1, audio mutes if no signal is present.
092 - RGB2 ENABLE (Red-Green-Blue 2 Enable)
Set to 1 to enable display panel Video 3 input for
Composite Video, set to 2 to enable for S-Video. Set to
0 to disable display panel Video 3 input.
094 - SAP MENU EN (2nd Audio Program)
Set to 1 to enable SAP feature, if available.
Set to 0 to disable SAP feature.
096 - DEE ASR RATIO (Default Aspect Ratio)
Selects default aspect ratio at power up, see settings
below.
Set to 0 for set by program.
Set to 1 for 4:3.
Set to 2 for 16:9 (Factory Default).
Set to 4 for Zoom 1
Set to 5 for Zoom 2
102 - ATSC BAND
Sets up TV to receive different types of incoming signals:
0=Broadcast, 1 =CATV, 2=HRC, 3=IRC, 4=Same as
NTSC.
103 - ATSC TUNE MODE
Selects ATSC tuning mode: 0=Virtual, 1 =Physical.
*Note: The setting above is ignored if Installer item 102 ATSC
BAND, is set to 1 -CATV, 2-HRC or 3-1RC Then 103 - ATSC
TUNE MODE above always resets itself to Physical (1), regardless
of what value appears for item 103 on the Installer menu.
104 - START MINOR CHANNEL
Sets XX-XX minor starting channel at power up:
0=NTSC. If not 0, number selected is the Minor start
channel number.
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to 1 to retain previous aspect ratio with power Off.
Set to 0 to retain default aspect ratio with power Off.
See item 96. Default Aspect Ratio above.
107 - BANNER SELECT
Not applicable.
116 - VIDEO MUTE EN (Video Mute Enable)
Set to 0 for normal.
Set to 1 for blank.
N
0
r"rl
N
0
r"rl
090 - KEY LOCK
If set to 1, display panel keyboard is locked out, not
available to end user. IR receiver remains functional.
091 - YPrPb2 EN. (Rear Component Video 2 Enable)
Set to 1 to enable display panel Component 2 input.
Set to 0 to disable display panel Component 2 input.
117 - FACT DEFAULT (Factory Default)
Set to 0 for normal.
Set to 1 to load default settings for all installer menu
items.
_ ARNING: Setting this to 1 will reload the
factory defaults and clear the channel list
including erasing any assigned Channel Icons
and Labels.
65