Cisco AJ732A - MDS 9134 Fabric Switch Release Note page 16

Upgrading Your Cisco MDS SAN-OS Software Image
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m
FC-Redirect configuration for hosts or target connected locally
•
FC-Redirect configuration created by application running on that switch.
•
If an upgrade is attempted when an active configurations is present, the switch will go into a disruptive
upgrade.
Note The software upgrade information in
system software disrupts IP traffic and SSM intelligent services traffic.
Table 7
Current
SAN-OS 3.3(1c) You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
SAN-OS 3.3(1a) You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
SAN-OS 3.2(3a) You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
SAN-OS 3.2(3)
SAN-OS 3.2(2c) You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
SAN-OS 3.2(1a) You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
SAN-OS 3.1(4)
SAN-OS 3.1(3a) You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
SAN-OS 3.1(2b) You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
SAN-OS 3.1(2a) You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
SAN-OS 3.1(2)
SAN-OS 3.1(1)
SAN-OS 3.0(3a) You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
SAN-OS 3.0(3)
SAN-OS 3.0(2a) You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
SAN-OS 3.0(2)
SAN-OS 3.0(1)
SAN-OS 2.1(3)
SAN-OS 2.1(2e) You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
SAN-OS 2.1(2d) You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
SAN-OS 2.1(2b) You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
SAN-OS 2.1(2)
Cisco MDS 9000 Family Release Notes for Cisco MDS SAN-OS Release 3.3(2)
16
Table 7
Nondisruptive Upgrade Path to SAN-OS Release 3.3(2)
Nondisruptive Upgrade Path
You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
You can nondisruptively upgrade directly to SAN-OS Release 3.3(2).
Upgrade to SAN-OS Release 2.1(2b) and then upgrade to Release 3.3(2).
or
Upgrade to SAN-OS Release 2.1(2d) and then upgrade to Release 3.3(2).
or
Upgrade to SAN-OS Release 2.1(2e) and then upgrade to Release 3.3(2).
or
Upgrade to SAN-OS Release 2.1(3) and then upgrade to Release 3.3(2).
applies only to Fibre Channel switching traffic. Upgrading
OL-14116-10