Black & Decker 9411 Owner's Manual
12" bandsaw
Table of Contents
Related Manuals for Black & Decker 9411
Summary of Contents for Black & Decker 9411
- Page 1 Wack c Decker@ owNER'S MANUAL Bond Saw 42" Band Saw...
-
Page 2: Safety Instructions
INTRODUCTION 13. DISCONNECT TOOLS before servicing; when Cut intricate designs, scroll and straight cut. The new changing accessories such as blades, bits, cutters, 9411 12" Band from Black & Decker is built the serious wood worker. With convenient up-front etc. - Page 3 Your Band Saw carton contains the following parts: CAUTION: When servicing Double-Insulated Tools, Catalog # 9411 12" Band Saw ONLY IDENTICAL REPLACEMENT PARTS. Band Saw Quadrant and Table Assemblys Replace or repair damaged cords. Band Blade...
- Page 4 Remove blade from carton examine ASSEMBLY (continued) closely. It's possible that the blade is inside out. Hold the blade as shown in Figure 4 with the teeth Installation of Band Blade facing you. Examine the teeth in your right hand. (Turn OFF and UNPLUG Band saw) The teeth should be pointing down.
- Page 5 ASSEMBLY (continued) Figure 8 UPPER BLADE Figure 6 GUIDE ASSEMBLY Blade Guard Blade Guide Bearing Blade Guide Screw Drive Pulley To Lower Blade Guide Assembly and Drive Pulley ADJUSTMENTS Fine Tuning Blade Tension (Turn OFF and UNPLUG Band saw) (Turn OFF and UNPLUG Band saw) Blade Tensioning Close side...
- Page 6 Adjusting the Blade Guides (Turn OFF and UNPLUG Band saw) Adjust Upper Guide First. Blade Guard UPPER BLADE 1. Loosen the Blade Guard Adjustment Knob, shown DANGER GUIDE ASSEMBLY KEEPHAXOS in Figure1, and lower the BladeGuardabout halfway. AWAY FROM BLADE 2.
- Page 7 Installation of Band Table and Quadrant Assembly (continued) Blade -—Table Insert Fit the Table and Quadrant assembly onto the saw, as shown in Figure 14. Carefully slip the table slot around the saw blade and align the Table Mounting Slot in the Quadrant with the Table Mounting...
-
Page 8: Pre-Operation
Squaring the Table (continued) PRE-OPERATION CHECK LIST (Turn OFF and UNPLUG Band saw) When you have finished aligning the table top to the Before operating your Band Saw, check the items listed blade, adjust the pointer shown in Figure 17. below to be sure the saw is ready to cut. - Page 9 USING YOUR BAND SQUARING THE MITRE GAUGE & SLOT (continued) Now that your Band Saw is fully assembled and ready Using the mitre gauge, make a test cut in a piece of to go, you'll be anxious to try it out. Unless you are very scrap wood and check the cut with your square.
-
Page 10: Using Your Band Saw
SAWING TIPS: MAINTENANCE (Turn OFF and UNPLUG Band saw) Keep the workpiece moving when cutting curves. After extended use of your saw, the tips of the blade Do not attempt to turn unless the workpiece guide screws may become worn down. Check the screw moving into the cutting edge of the blade. - Page 11 Cut along this line and position as desired on wood. EDGE OF BOARD 14 1516 17...
- Page 13 EOGE : 22 1516 17...
- Page 14 151617...
- Page 15 NOTES...
-
Page 16: Home Use Warranty
IMPORTANT To assure product SAFETY and RELIABILITY, repairs and maintenance should be performed by Black & Decker Service Centers or other qualified service organizations, always using Black & Decker replacement parts. HOME WARRANTY (A FULL TWO YEAR WARRANTY) Black & Decker warrants this product for two years against any defects... - Page 17 This unit has been suppliéd with one 3/16" and one 1/4" blade. 3/16" blade will provide better scrolling ability for tighter curves than the 1/4" blade. The 1/4" blade is more suitable for larger curves and straight cuts. BLADE SELECTIO WARNING: To prevent injury, keep away from blade and other...
Need help?
Do you have a question about the 9411 and is the answer not in the manual?