Download  Print this page

Kenmore 8787 - Elite HE3 7.0 cu. Ft. Electric Dryer Use And Care Manual page 23

Use and care guide
Hide thumbs


Table of Contents
Damp Dry Signal
Select the Damp Dry Signal to alert you that your clothes are
80% dry. This is usdul when you want to remove
lightweight items in a mixed load to avoid overdrying or remove
partially dry items that may need ironing.
NOTE: The Damp Dry Signal is available only with the Auto
Button Sounds
You can change the volume of the sound of the beeps. Press
BUTTON SOUNDS until the desired volume (Loud, Soft or Off)
glows. The Power and Cancel buttons will still beep softly when
the Button Sounds volume is set to Off.
Drum Light
Press Drum Light to turn on the light inside the dryer drum.
During a cycle, if Drum Light is selected, the drum light turns on
and will remain on until DRUM LIGHT is pressed again, the door
is open and closed, or the door is left open for 5 minutes.
When the dryer is not running, the drum light will turn on when
DRUM LIGHT is pressed or the dryer door is opened, and it will
remain on until the dryer door has been open for 5 minutes, the
dryer door is closed or DRUM LIGHT is pressed again.
Press DRUM LIGHT at any time to turn the drum light ON or OFR
Use Modifiers to select time, temperatures and dryness levels for
the Timed Cycles.
Press MORE TIME or LESS TIME until the desired drying time is
displayed. The time cannot be changed with Auto Cycles.
Press TEMPERATURE until the desired temperature
glows. Temperature modifiers cannot be used with the Auto
Cycles or with the Air Fluff cycle.
Medium Hgh
Extra Low
Air Dry
Dryness Level
Press DRYNESS LEVEL until the desired Dryness Level is
selected. Dryness Level cannot be adjusted with Timed Cycles.
More Dry
Less Dry
You can change Auto Cycles, Timed Cycles, Modifiers and
Options anytime before pressing Start.
Three short tones sound if an unavailable combination
selected. The last selection will not be accepted.
Cycles after pressing Start
1. Press STOP twice. This ends the current cycle.
2. Select the desired cycle and options.
3. Press and hold START. The dryer starts at the beginning of
the new cycle.
NOTE: If you do not press START within 5 minutes of selecting
the cycle, the dryer automatically
shuts off.
and Options after pressing Start
You can change a Modifier or Option anytime before the selected
Modifier or Option begins.
1. Press STOP once.
2. Select the new Modifier and/or Option.
3. Press and hold START to continue the cycle.
NOTE: If you happen to press Stop twice, the program clears and
your dryer shuts down. Restart the selection process.
Changing the Preset Dryness Level Settings
If all of your loads on all Auto Dry cycles are consistently
not as
dry as you would like, you may change the preset Dryness Level
settings to increase the dryness. This change will affect all of your
Auto Dry cycles.
Your Dryness Level settings can be adjusted to adapt to different
installations, environmental
or personal preference.
There are 3 drying settings: 1 (factory preset dryness level),
2 (slightly dryer clothes, approximately
15% more drying time)
and 3 (much dryer clothes, approximately
30% more drying
1. The Dryness Level settings cannot be changed while the
dryer is running.
2. Press and hold the DRYNESS LEVEL button for 5 seconds.
The dryer wil beep, and "CF" will be displayed for 1 second
followed by the current drying setting.
3. To select a new drying setting, press the DRYNESS LEVEL
button again until the desired drying setting is shown.
NOTE: While cycling through the settings, the current setting
will not flash, but the other settings will flash.
4. Press START to save the drying setting.
The drying setting you selected will become your new preset
drying setting for all Auto Dry cycles.

Hide quick links:


Table of Contents

This manual is also suitable for:

He3 110.8787 seriesHe3 110.8789 series