ACT ACTPRO 3000 ACCESS CONTROL UNITS Operating And Installation Instructions

ACT ACTPRO 3000 ACCESS CONTROL UNITS Operating And Installation Instructions

Access control units
Hide thumbs Also See for ACTPRO 3000 ACCESS CONTROL UNITS:
Table of Contents

Advertisement

Access Control Technology
ACTpro 3000 Access Control Units
Operating & Installation Instructions
18 00035

Advertisement

Table of Contents
loading

Summary of Contents for ACT ACTPRO 3000 ACCESS CONTROL UNITS

  • Page 1 Access Control Technology ACTpro 3000 Access Control Units Operating & Installation Instructions 18 00035...
  • Page 4 Ordering Information Access Control Technology...
  • Page 5 Operating Instructions for ACTpro 3000 Access Control Unit...
  • Page 6 Operator Menu...
  • Page 9 The usual site coded cards are disabled if any batch cards are assigned on the system. However, site coded cards may be entered as a batch. Learned cards operate as normal.
  • Page 17 Installer Menu...
  • Page 20 are doors that are inside the perimeter of the installation. Access is denied on these doors if the cardholder has not already entered through the perimeter or Anti-passback doors...
  • Page 21 Monitor Arming...
  • Page 22 Arm Intruder...
  • Page 27 Ethernet Leds Link Led Indicates connection to Switch/Hub. Leds indicate activity on NET1/SERIAL, DOORS and NET2 TX/RX Indicates reception/transmission or collision. NET2 Network 2 NETWORK 1 B 0V B 0V Card/Proximity or Pin Card/Proximity or Pin Reader - Door 1 Doors Reader - Door 2 Cable: 8 Core Screened...
  • Page 28 DOORS Entry Reader GREEN DATA CLOCK SENSE Required Address Required Address 5A 250VAC 5A 30VDC...
  • Page 29 ACTpro200 Installation 2 Door Controller and Monitored Power Supply WARNING: ACTpro 2000 MAINS VOLTAGE NETWORK DISCONNECT BEFORE MAINTENANCE LED Functionality: Red LED indicates the status of communications with the Controller. While online to the controller the Red LED will flash rapidly. If there is a problem it will flash slowly (about once a second).
  • Page 30 +12V. The +5V reader supply on ACT controllers is normally rated at 100mA. Typically this is sufficient to power 2 ACT readers. Note however that readers from other manufacturers may need to be powered separately if their current requirements exceed...
  • Page 31 ACTpro 3000 Cable Connections Direct Connection Cable (PC COM Port to Controller) 1 2 3 4 5 DB9 Female (Rear View) 6 7 8 9 Max cable length is 5m using standard alarm cable or 30m using twin twisted-pair (use 0V in each pair) Serial Printer Cable DB25 Male (Rear View)
  • Page 32 OUTPUTS 2 INPUTS GREEN DATA CLOCK SENSE 1A 250VAC 1A 30VDC +12V PRESENT MAINS TAMPER 5A 250VAC 5A 30VDC N/C C N/ON/C C N/O 1A 250VAC 1A 30VDC INPUTS OUTPUTS GREEN DATA CLOCK SENSE 5A 250VAC 5A 30VDC N/C C N/ON/C C N/O...
  • Page 33 NETWORK 1 NETWORK 2 Direct Connect Cable B 0V B 0V ACTWin pro From the Installer Menu, do the following: 1. Factory Default the controller. 2. Go to the Communications menu and Set Address. If there is only 1 controller, set the address to 1. For more than 1, assign each controller a unique address, starting at 1.
  • Page 34 ACT 4-Line Nework Interface Card To PC RS232 PORT RS485 RS485 RS485 232 Interface 232 Interface Converter Converter Connections for 9 Way Connector of PC SCN = Pin 5 LED2 C = Pin 7 To Mains Supply DI = Pin 3...
  • Page 35 12V DC Power Supply (300mA) RS-232 +12V Function ACTWin Software +12V 0V & Shield RS-485 Bus Network cable use either: (1)Single shielded twisted pair: Belden 9501 or similar (2)CAT5 Cable: A/B must share the same twisted pair. To next Controller Shield A B 0V A B 0V...
  • Page 38 3. Controller(s) now ready to receive calls ACTWin pro Setup for Modem Operation 1. Connect the ACT modem to the PC and install modem driver. 2. In ACTWin pro, Click on the Locations and Connections icon on the toolbar. 3. Configure the remote site name in the Location Name.
  • Page 39 ACTpro 3000 supports TCP/IP networking over a LAN using twisted pair Ethenet (10Base-T and standard RJ45 connector). LEDS: LINK Lights Solid Green to indicate RJ45 Network port is connected to the Network. TX/RX Blinks red to indicate packet transmission and reception, also blinks to indicate network collisions.
  • Page 40 Wiring for Radio Receiver All Channels Enabled (Switches 1 to 4 ON) Standard ISO Track 2: Start Sentinel + 16 Digits + Seperator + End Sentinel + LRC + DO D1 GND EN 24V GND 12V Prastel MRRE Receiver Controller SENSE CLOCK DATA...
  • Page 41 PUSH BUTTON DOOR CONTACT 5A 250VAC 5A 30VDC N/C C N/ON/C C N/O RELAY AUX RLY 1A 250VAC 1A 30VDC INPUTS OUTPUTS...
  • Page 42 DOORS INPUTS...
  • Page 43 ACTpro 3000 System Diagram ACTWin pro ACTWin pro RS232 Modem RS232 ACTpro 3000 ACTpro 3000 Door 1 Door 1 PSTN Door 2 Door 2 RS485 ACTpro 2000 Door 1 ACTpro 100 ACTpro100 ACTpro100 Door 2 ACTpro 3000 Door 1 Modem Door 4 4 Line Interface Door 3...

Table of Contents