THUNDER TIGER TITAN X50 Instruction Manual page 6

MANUAL FORMAT / 說明書使用方式
How to read the instruction manual?
說明書導讀
A: Indicates the assembly step number and the parts bags that are to be assembled.
B: Displays actual size drawings, and part quantities used.
C: All parts, except screws, are identified by its order numbers. When purchasing spare parts, identify the part
required and cross reference this to the spare parts list in the end of this maunal, which shows the purchasable
spare parts and the corresponding order numbers.
D: This instruction manual uses several symbols. Pay careful attention to them during construction. Details are given at
the bottom of each page.
A: 顯示組立步驟及需組立之零件包順序
B: 零件實際對照尺寸及使用數量
C: 請比對零件形狀以及後附零件料號對照圖示找出需求零件料號
D: 操作說明符號可更有效協助組裝者使用此說明書，請依說明書符號指示進行組裝步驟
Example
Main Rotor-5 /
Bag A
No. Material No. Description
名稱
1 BK1502 HARDENED MAIN SHAFT 高強度主軸
2 BK1086 SOCKET SCREW M2×14 M2×14
內六角半牙螺絲
3 HML2 M2 NUT M2 螺帽
C
Step 1 / 步驟一
1. Insert the main rotor head set into the Main Shaft. Note the end with a
BK1086 hole of the Main Shaft has to insert into the Hub.
SOCKET SCREW M2×14 2. Line up the holes on the Main Shaft & Hub.
M2×14 3. Insert the Socket Screw (M2 x 14, #2) through the Hub and apply a
內六角半牙螺絲
drop of threadlocking to screw it with the Nut.
1. 將主軸穿過組裝完成的主旋翼頭組。
2. 對正主軸及固定座上孔位。
HML2
3. 以半牙內六角螺絲穿過固定座及主軸後，
M2 NUT
套上螺帽並使用適量防鬆劑固定。
M2
螺帽
B
SYMBOLS USED THROUGHOUT THE MANUAL / 符號說明
The parts in the Titan X50 are packed according to each major assembly steps. The part number and quantity are always
shown in the square box on each page. As good practice, only open up the bag that you need for the paticular assembly.
零件均依照組裝步驟包裝，請依照組裝程序，逐一開啟零件包，避免零件遺失。
Note / 注意
Assembly drawings will contain icons that indicate use of
Threadlocker or CA glue as needed.
Examples of the icons are as right shown:
請依組裝步驟圖示，使用防鬆膠或接著劑。
圖示範例如右：
Apply C.A Glue
使用快乾膠黏合
Apply threadlocker
使用螺絲防鬆膠
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble in right order
依標示順序組裝
-5
Qty
1
1
2
B A
(3)
The hole should point up.
請注意，有孔位的一端應朝上
Cut off shaded portion
依標示部分裁切
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Drill holes with the specified diameter
依標示尺寸鑽孔
Must be purchased separately
改裝品需另購
C
(2)
T22
D
(1)
T22(#262)
CA
-5-
THREADLOCKER / 螺絲防鬆膠
CA GLUE / 快乾膠
Cut off excess
裁剪多餘部分
Apply grease
使用潤滑油膏(黃油)
Pay close attention here
注意組裝步驟
Hint
組裝提示