Sealey SM65.V3 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear protective
instruction gloves
manual
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using.
Inspect power supply leads, plugs and all electrical connections for wear and damage.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
WARNING! When using electric tools basic safety precautions should always be followed to reduce the risk of fire, electric shock and
‰
personal injury including the following. Read all these instructions before attempting to operate this
product and save these instructions.
DO NOT use worn or damaged cables, plugs or connectors.
8
Ensure that any faulty item is repaired or is replaced immediately by a qualified electrician.
9
If the cable or plug is damaged during use, switch off the electricity supply and remove from use.
9
Ensure that repairs are carried out by a qualified electrician.
Sealey recommend that an RCD (Residual Current Device) is used with all electrical products.
9
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable.
8
1.2. GENERAL SAFETY
WARNING! Disconnect the bandsaw from the power source before servicing, changing accessories or performing any other maintenance.
‰
Familiarise yourself with applications and limitations of the product, as well as the potential hazards.
9
Keep work area clear. Cluttered areas and benches invite injuries. Consider your work area environment.
9
DO NOT expose tools to rain.
8
DO NOT use tools in damp or wet locations.
8
DO NOT use tools in the presence of flammable liquids or gases.
8
DO NOT let persons, especially children, not involved in the work touch the tool or the extension cord and keep them away from the
8
work area.
DO NOT force the tool, It will do the job better and safer at the rate for which it was intended.
8
DO NOT force small tools to do the job of a heavy duty tool.
8
DO NOT use this machine for anything other than its intended purpose. The machine is designed for light metal cutting work in engineering
8
workshops, garages, metal fabricators, etc.
Dress properly. DO NOT wear loose clothing or jewellery, they can be caught in moving parts.
8
DO NOT overreach. Keep proper footing and balance at all times.
8
DO NOT use the tool if the switch does not turn it on and off.
8
DO NOT start the machine until the workpiece is secure and the blade has been lowered to just above the workpiece.
8
DO NOT use the bandsaw with the blade guard or pulley cover removed.
8
DO NOT use damaged or deformed blades.
8
DO NOT run the saw with the blade in the raised position.
8
DO NOT use the machine in wet or damp locations.
8
DO NOT use the machine in areas where fumes from paint, solvents, or flammable liquids pose a potential hazard. Keep all flammable
8
materials (including wipers or cleaning rags) away from the saw, and dispose of according to local regulations.
DO NOT stand on the machine.
8
DO NOT leave machine running unattended. Turn power switch 'Off' and DO NOT leave area until machine has come to a complete stop.
8
DO NOT use whilst under the influence of drugs, alcohol or other intoxicating medication. DO NOT use the tool if you are tired.
8
Keep work area well lit. Optimum working temperature 18
9
Guard against electric shock.:Avoid body contact with earthed or grounded surfaces.
9
Keep other persons away.
9
Store idle tools.
9
When not in use, tools should be stored in a dry locked-up place, out of reach of children.
9
Use the right tool.
9
Non-skid footwear is recommended when working outdoors.
9
© Jack Sealey Limited
150MM 3-SPEED METAL CUTTING BANDSAW
WITH QUICK LOCK VICE & STAND
MODEL NO: SM65.V3
Wear eye Wear face
protection mask
Original Language Version
Wear ear Wear protective
protection clothing
C to 30 C.
o o
Indoor use Warning
only
SM65.V3 Issue 1
Wear
protective
footwear
23/10/24