Creating A Video Wall; Cable Management - NEC 60XM5 - PlasmaSync - 60" Plasma Panel User Manual

Creating a video wall

With built-in matrix display capability, you can create a (2 2, 3 3, 4 4, 5 5, 5 1, 1 5) video wall.
• Connect signal cables and remote cables as shown below.
Video signal
VIDEO Signal
IN
RCA phono plug
VIDEO AUDIO 1 DVD 1 / HD 1 AUDIO 2
2
R R
1 (IN/OUT) R/Cr/Pr
3 Y Cb/Pb Cr/Pr
L
(MONO) L (MONO)
BNC connector
OUT
VIDEO Signal
Note:
1. The VIDEO1 and RGB1 terminals can be used for either INPUT or OUTPUT.
When LOOP OUT is ON, do not connect an OUTPUT signal from another unit as it may damage the other unit due to an
extraordinary load.
2. LOOP OUT can not be turned ON while signals are input to the RGB1 terminal.
3. LOOP OUT can be turned ON while signals are input to the RGB1 terminal if the POWER is switched ON.
Information
• To loop signals out to another plasma display, set the LOOP OUT to ON.
• To create a video wall, set the VIDEO WALL menu items properly.
• To connect monitors, please use a 1 m to 2 m (3.3 feet to 6.6 feet) BNC cable (any commercially available cable).
• If the image quality is poor, do not use the monitor's out terminal. Use a distribution amplifier (any commercially
available distribution amplifier) to connect the split signals to the respective monitor INPUT terminals.
• Being used as a video wall function, maximaly 4-screen is rough-standard with lower than 1024 768, 60 Hz
signal.
• A distribution amplifier is particularly recommended when creating a 3 3 (or greater) video wall.
• When looping from plasma to plasma, a 1 m to 2 m (3.3 feet to 6.6 feet) 15 pin male D-Sub - 5BNC conversion
cable is required.

Cable Management

Using the cable clampers and beads bands provided with the plasma display; Bundle the signal and audio cables at the
back of the unit to connect to the display.
42XM5
Back of the unit
mounting holes
To attach
Insert q into a mounting hole, then
snap w into the back of q to fix the
clamper.
Clampers are designed to be difficult
to undo once in place. Please attach
carefully. Cables can be routed to the
right or left.
RGB 2 / DVD 2 / HD 2 RGB 1 AUDIO 3
RGB 3 EXTERNAL CONTROL
R
G/Y B/Cb/Pb HD VD
(IN/OUT) DV I ( Digital RGB )
L (MONO)
50XM6
Bunch separated cables together and
secure them with the provided beads
bands.
Do not allow excessive stress to be
placed on the ends of cables.
RGB/DVD/HD signal
Remote
control
IN
BNC connector
REMOTE
VIDEO AUDIO 1 DVD 1 / HD 1 AUDIO 2
2 R
R
IN OUT
1 (IN/OUT)
3 Y Cb/Pb Cr/Pr
L
(MONO) L (MONO)
OUT
Remote
control
Back of the unit
mounting holes
En-6
RGB signal/
DVD/HD signal
IN
RGB 2 / DVD 2 / HD 2 RGB 1 AUDIO 3 3
RGB EXTERNAL CONTROL
R
R/Cr/Pr G/Y B/Cb/Pb HD VD
DV I ( Digital RGB )
(IN/OUT)
L (MONO)
OUT
RGB signal/
DVD/HD signal
60XM5
Back of the unit
mounting holes
To detach
Using pliers, twist the clamper 90° and
pull it outward. In some cases the
clamper may have deteriorated over
time and may get damaged when
removed.
Remote
control
IN
REMOTE
IN OUT
OUT
Remote
control