362Xp; Technical Data; Recommended Original And Replacement Bar And Chain Combinations - Husqvarna 362Xp Operator's Manual

362XP

Engine
Cylinder volume,
3
cu.in/cm 3,8/62,4
Cylinder bore, inch/mm 1,85/47
Stroke, inch/mm 1,4/36
Idle speed, rpm 2 700
Power, kW/ rpm 3,4/ 9 600
Ignition system
Manufacture FHP
Type of ignition system CD
Spark plug Champion
RCJ 7Y
Electrode gap, inch/mm 0,02/0,5
Fuel and lubrication
system
Manufacturer Walbro
Carburetor type HD12
Fuel capacity,
US pint/litre 1,63/0,77
Oil pump capacity at
8500 rpm, ml/min 4–20
Oil capacity, US pint/litre 0,89/0,42
Type of oil pump Automatic
Weight
Without bar and chain,
Lbs/kg 13,2/6,0
XPG:13,7/6,2
Chain/bar
Recommended bar
lengths, inches/cm
13-24"/33-61
Usable cutting length,
inches/cm 12-23"/31-58
Chain speed at max.
power, m/sec 21,4
Pitch, inch/mm 3/8"/ 9,52
0,325"/ 8,25
Thickness of drive link,
inch/mm 0,050"/1,3
0,058"/1,5
0,063"/1,6
Number of teeth on
drive sprocket 7
34
– English

TECHNICAL DATA

365 372XP
4,0/65,1 4,3/70,7
1,89/48 1,97/50
1,4/36 1,4/36
2 700 2 700
3,4/ 9 300 3,9/ 9 600
FHP FHP
CD CD
Champion Champion
RCJ 7Y RCJ 7Y
0,02/0,5 0,02/0,5
Zama Walbro
C3M-EL8 HD12
1,63/0,77 1,63/0,77
4–20 4-20
0,89/0,42 0,89/0,42
Automatic Automatic
13,2/6,0 13,4/6,1
XPG:13,8/6,3
15-28"/38-71 15-28"/38-71
14-27"/35-69 14-27"/35-69
20,7 21,4
3/8"/ 9,52 3/8"/ 9,52
0,050"/1,3 0,050"/1,3
0,058"/1,5 0,058"/1,5
0,063"/1,6 0,063"/1,6
7 7
´*3&e¶5K¨
Recommended original and replacement
bar and chain combinations
These Husqvarna saw models are in the ANSI category of saws
above 3,8 cu. in. and are not required to comply with low kickback
performance requirements. However, for these models we
recommend the following cutting equipment.
Model 362
Guide bar
Length Pitch Max nose
inch inch radius
15 0,325 10T
16 0,325 10T
18 0,325 10T
20 0,325 12T
15 3/8 11T
16 3/8 11T
18 3/8 11T
20 3/8 11T
24 3/8 11T
Model 365 and 372
Guide bar
Length Pitch Max nose
inch inch radius
15 3/8 11T
16 3/8 11T
18 3/8 11T
20 3/8 11T
24 3/8 11T
28 3/8 11T
Note: For the chains above you are free to choose between 0,050"
and 0,058" gauge drive link for the corresponding bar, see the table
below.
0,050"/1,3 mm 20VB 20LP
0,058"/1,5 mm H25/21VB H21/21LP H42/73LP EM S48/73LG
0,063"/1,6 mm 22VB 22LP
The combinations of powerhead, bar and chain have been
investigated in accordance with the vibration requirements of
ANSI B 175.1-1991.
!
WARNING! These models of chain saws are capable
of severe kickback that could result in serious
injuries to the user. Do not operate these saws unless
you have extraordinary cutting needs and experience
and specialized training for dealing with kickback.
Saws with significantly reduced kickback potential
are available. Always use the safest saw and cutting
equipment applicable to your cutting need.
Saw chain
Husqvarna H25 / H21 or
Oregon 21VB / 21LP
Husqvarna H42 / EM S48 or
Oregon 73LP / 73LG / 73V
Saw chain
Husqvarna H42 / EM S48 or
Oregon 73LP / 73LG
72LP 72LG 72V
73V
75LP 75LG 75V