GE NX-1308E - Caddx 8 Zone LED Keypad Installation And Startup Manual page 32

Networx series
Table of Contents

Advertisement

LOCATION 81 - START PROGRAM AND END PROGRAM COMMUNICATOR CODES, SLOW SPEED FORMATS
ONLY (4 segments, numerical data)
Location 81 contains the tens and ones digits for a 4+2 format that will be sent if "Start / End Programming Reporting"
is enabled. Segment 1 contains the tens digit of the "Start Program Reporting". Segment 2 contains the ones digit of
the "Start Program Reporting". Segment 3 contains the tens digit of the "End Program Reporting". Segment 4
contains the ones digit of the "End Program Reporting".
LOCATION 82 - END DOWNLOAD COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY (4 segments,
numerical data)
Location 82 contains the tens and ones digits for a 4+2 format that will be sent if "End Downloading Reporting" is
enabled. Segment 1 and 2 are reserved. Segment 3 contains the tens digit of the "End Download Reporting".
Segment 4 contains the ones digit of the "End Download Reporting". Note: A start download report will be sent to the
internal event log.
LOCATION 83 - CANCEL COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY (1 segments, numerical
data)
Location 83 contains the tens digit for a 4+2 format that will be sent if "Cancel Reporting" is enabled. Segment 1
contains the tens digit for the "Cancel Communicator Reporting". The ones digit is the ones digit of the user who
canceled. If the user number is greater than 9, the numbers will begin repeating (i.e. 9 for user 29). If it is
required to report Cancels for more than 9 users, Contact ID or SIA format must be used.
LOCATIONS 84-87 RESERVED.
***
LOCATIONS 88-109 ARE FOR PROGRAMMING DIFFERENT ACCOUNT CODES AND/OR
***
FEATURES FOR EACH PARTITION. IF A LOCATION IS LEFT UNPROGRAMMED, THE
**
FEATURE FOR PARTITION 1 AND ACCOUNT CODE FOR THE PHONE NUMBER WILL BE USED
LOCATION 88 - ACCOUNT CODE FOR PARTITION 1 (6 segments, numerical data)
Location 88 contains the account code sent when partition 1 is reported. If location 88 is left unprogrammed (all
A10"s), then the account code corresponding to the Phone number dialed will be used. If the account code is
less than six digits, program a A10" in the segment immediately after the last digit of the account code. If the account
code is 6 digits long, program all 6 segments.
LOCATION 89 - ACCOUNT CODE FOR PARTITION 2 (6 segments, numerical data)
Location 89 contains the account code sent when partition 2 is reported. If location 89 is left unprogrammed (all
A10"s), then the account code corresponding to the Phone number dialed will be used. If the account code is
less than six digits, program a A10" in the segment immediately after the last digit of the account code. If the account
code is 6 digits long program all 6 segments.
LOCATION 90 - PARTITION 2 FEATURE AND REPORTING SELECTIONS (3 segments, feature selection data)
Location 90 is used to enable certain features that can be accessed or are visible to the user from the keypad of the
system.
In addition, certain communicator reports are enabled in this location. Each of these features can be
enabled by partition. This location contains 3 segments, with eight possible features per segment. Refer to Location
23, Segments 1,2, and 3 (page 19) for the feature selections. If all segments are blank (nothing enabled), the
features for partition 1 will be used.
LOCATION 91 - PARTITION 2 ENTRY EXIT TIMERS (4 segments, numerical data)
Location 91 is used to enter in seconds the Entry and Exit times. There are 2 separate entry and exit times. Valid
entries are 10-255 seconds. If all segments are A0", the entry and exit times for partition 1 will be used.
Segment 1, Entry time 1: Entry time that will be used when a Delay 1 zone type initiates an entry delay.
Segment 2, Exit time 1:
Segment 3, Entry time 2: Entry time that will be used when a Delay 2 zone type initiates an entry delay.
Segment 4, Exit time 2:
LOCATION 92 - ACCOUNT CODE FOR PARTITION 3 (6 segments, numerical data)
The account code sent when partition 3 is reported is programmed in location 92.
unprogrammed (all A10" ) then the account code corresponding to the Phone number dialed will be used. If
the account code is less than six digits, program a A10" in the segment immediately after the last digit of the account
code. If the account code is 6 digits long program all 6 segments.
32
Exit time that will be used for all zones designated as Delay 1.
Exit time that will be used for all zones designated as Delay 2.
***
***
**
If location 92 is left
NX-8 Control

Advertisement

Table of Contents
loading

This manual is also suitable for:

Networx nx-8

Table of Contents