Assign The Avr Input Connectors; Set Up The Network - Harman Kardon AVR 1700 Owner's Manual

AVR
8. Select "5.1."
9. the test will begin. make sure that the room is quiet while the test noise is playing
through the speakers.
10. when the test finishes, press the remote's oSd button to exit.

Assign the AVR Input Connectors

1. review the input connections you listed on the connection table, on page 13. note what
changes (if any) you have made from the default AVr Input connector assignments
that appear on the list. If you connected your so urce devices according to the entries
in the "default AVr Input connector" column of the table on page 13, you can skip
this section.
2. turn on your tV and select the tV input where you connected the AVr in Connect Your
TV or Video Display, on page 13.
3. press the remote control's oSd button. the AVr's on-screen display (oSd) master
menu will appear on the tV.
NOTE: If you have used a composite video connection to your TV, the OSD menus
will not appear on your TV. Follow the steps below using the AVR's front-panel
display.
M A S T E R M E N U
S o u r c e S e l e c t
S o u r c e S e t u p
S u r r o u n d M o d e
E z S e t / E Q
M a n u a l S e t u p
N e t w o r k
S y s t e m S e t u p
4. use the remote's arrow and ok buttons to select "Source Setup." If there is a Source
Selector for which you want to assign different video or audio connections. use the left/
right arrow buttons to select it, and press the ok button.
S o u r c e S e t u p
S o u r c e
T i t l e
V i d e o I n
A u d i o I n
T o n e
B a s s
T r e b l e
N i g h t M o d e
R e c o r d O u t
5. Select "Video In" and use the left/right arrow buttons to select the video input connector
you want to assign to the Source Selector button. press the ok button.
NOTE: If you select an HDMI connector for the Video connection the Audio
connection will automatically change to the same HDMI connector.
S o u r c e S e t u p
S o u r c e
T i t l e
V i d e o I n
A u d i o I n
T o n e
B a s s
T r e b l e
N i g h t M o d e
R e c o r d O u t
18
< C a b l e / S a t e l l i t e >
H D M I 1
H D M I 1
O u t
0
0
O f f
A n a l o g
< C a b l e / S a t e l l i t e >
H D M I 2
H D M I 2
O u t
0
0
O f f
A n a l o g
6. Select "Audio In" and use the left/right arrow buttons to select the audio input
connector you want to assign to the Source button.
NOTE: If you have assigned an HDMI Video connector for the Source button you
cannot assign a different Audio connector.
S o u r c e S e t u p
S o u r c e
T i t l e
V i d e o I n
A u d i o I n
T o n e
B a s s
T r e b l e
N i g h t M o d e
R e c o r d O u t
7. repeat steps 4 – 6 for the remaining audio/video connections that you want to re-
assign.

Set Up the Network

to play mp3 or wmA media located on dlnA-compatible devices connected to the
network, to use the AVr's internal Internet radio tuner (vtuner) to listen to audio streams
or to stream audio to the AVr via Airplay, connect the AVr's network connector to the
ethernet port on a router or modem that has Internet access, to a home network, or to a
pc. (See Connect to Your Home Network, on page 15.)
we recommend that you connect the AVr directly to a home-network router so that it can
directly access the Internet for Internet radio and access other devices on the network
for playback of shared content (see Listening to Media on Your Home Network, on page
21, for more information).
If your network uses an automatic Ip address, you should not have to perform any
network setup procedures. once you connect the AVr to your home network, the network
should automatically assign the AVr an Ip address, and the AVr should automatically
connect to your network. If your AVr does not automatically connect to your network (in
which case the AVr will display a "not connected" message when you press the network
source button):
1. press the oSd button and select network. the network setup menu will appear.
N e t w o r k
I P C o n f i g u r a t i o n
I P A d d r e s s
S u b n e t M a s t
G a t e w a y
P r i m a r y D N S
S e c o n d a r y D N S
P r o x y C o n f i g
I P A d d r e s s
P o r t
2. Select Ip configuration, then press the left or right button twice to cycle the setting
from "Auto" to "manual" and back to "Auto."
3. Scroll to the bottom of the list and select "Apply & Save." the AVr will enter the Standby
mode. when you turn the AVr back on, it will attempt to connect to the network.
4. If the AVr again fails to connect to the network, you may need to enter your network's
settings manually. In this case, you must obtain these settings from your ISp or
network administrator. After obtaining your network's settings:
a) Select Ip Address and use the left or right button to change the setting to "manual."
the following settings will become active: Ip Address, Subnet mask, gateway,
primary dnS and Secondary dnS.
b) use the number buttons to make the entries for all of these settings.
Set Up the AVR, continued
< C a b l e / S a t e l l i t e >
C o m p o s i t e 1
O p t i c a l 1
O u t
0
0
O f f
A n a l o g
A u t o
0 0 0 . 0 0 0 . 0 0 0 . 0 0 0
2 5 5 . 0 0 0 . 0 0 0 . 0 0 0
0 0 0 . 0 0 0 . 0 0 0 . 0 0 0
0 0 0 . 0 0 0 . 0 0 0 . 0 0 0
0 0 0 . 0 0 0 . 0 0 0 . 0 0 0
O f f
0 0 0 . 0 0 0 . 0 0 0 . 0 0 0
0 0 0