iDM AERO SLM 6-17 Technical Documentation Installation Instructions

iDM AERO SLM 6-17 Technical Documentation Installation Instructions

Additional model: hgl without hgl with navigator 2.0 control air heat pump with inverter-technology
Table of Contents

Advertisement

T EC H N I C A L D O C U M E N TAT I O N
I N STA L L AT I O N I N ST R U C T I O N S
w i t h N AV I G AT O R 2 .
w i t h N AV I G AT O R 2 . 0 c o n t r o l
AIR HEAT PUMP WITH
INVERTER-TECHNOLOGY
HEAT PUMPS FROM AUSTRIA
www.idm-energie.at
A E R O S L M 3 - 1 1
A E R O S L M 6 - 1 7
A d d i t i o n a l M o d e l :
H G L
W I
W I T H O U T H G L
DIE ENERGIEFAMILIE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AERO SLM 6-17 and is the answer not in the manual?

Questions and answers

Summary of Contents for iDM AERO SLM 6-17

  • Page 1 N AV I G AT O R 2 . 0 c o n t r o l w i t h N AV I G AT O R 2 . AIR HEAT PUMP WITH INVERTER-TECHNOLOGY HEAT PUMPS FROM AUSTRIA www.idm-energie.at...
  • Page 2: Table Of Contents

    3.8. Connections outdoor unit AERO SLM 6-17 3.9. Technical data 3.10. Performance data AERO SLM 3-11 acc. to EN 14511 - heating 3.11. Performance data AERO SLM 3-11 acc. to EN 14511 - cooling 3.12. Performance data AERO SLM 6-17 acc. to EN 14511 - heating 3.13.
  • Page 3 It is essential heat pump. that this information is observed! General instructions on operating the Space for customer service telephone heat pump. number:_________________________ All rights reserved for modifi cations to the technology and design! (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 4: General Information

    . Heat pumps may only be installed by competent specialist staff and commissioned by a customer Heat pumps should not be installed in rooms with high service company trained to do so by iDM Energiesys- electromagentic infl uences from other installations! teme GmbH.
  • Page 5: Sound Emission

    Only original spare parts the indoor unit. Also the boiler room where the indoor which meet the requirements of iDM may be used! unit of the AERO SLM is installed should be placed outside of the noise sensitive living area. The boiler room should be furnished with a good lockable door.
  • Page 6: Acoustic Evaluation

    The sound power be calculated with the iDM-sound calculator. can only be determined via mathematical calculation calculation of the sound pressure level shall be calc...
  • Page 7 Finally, the determined rating level can be compared with legal limit values (e.g. „TA Lärm“). (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 8: Description

    - Non-return valve door unit are not in the scope of delivery of the heat pump. The parts are available as accessories and must be connected according to the technical specifi cations. (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 9: Dimensions Indoor Unit Aero Slm 3-11 And Aero Slm

    3 . 4. Co n n ection s i n door u n it A ER O S LM 3- 11 and A ER O S L M 6- 17 1 HGL fl ow 2 Heatpump fl ow 3 Heat pump return 4 Cable inlet main current 5 Refrigerant pipes 6 LAN-Connection 7 Cable inlet sensors (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 10: Dimensions Outdoor Unit Aero Slm

    3 .6. Co n n ections ou t d oor u n it AE R O SLM 3- 1 1 (V i e w f r o m be lo w) Outlet side Refrigerant pipe connections Ø12 mm und Ø16 mm Condensation drain 1“ Inlet side (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 11: Connections Outdoor Unit Aero Slm

    3 . 7. Dimen si ons ou t door u n it AER O S LM 6- 1 7 Side view / left Front view Outlet side Inlet side 3 . 8. Co n n ection s ou t d oor un it AE R O SLM 6- 1 7 (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 12: Technical Data

    Sound power level maximum outdoor unit dB(A) Sound reduced operation outdoor unit (reduced power) dB(A) The sound pressure level can be calculated with the iDM-sound calculation tool Dimensions indoor unit Height / Width / Depth 1262/ 620 / 762 Weight Minimum size of installation room (with standard fi...
  • Page 13 Heat pump type AERO SLM 3-11 HGL AERO SLM 6-17 Unit Maximum heating supply temperature °C Regrigerant R410A R410A Quantity of refrigerant 4.1 (up to 6 m) 4.78 (up to 6 m) 1924 Compressor oil EMKARATE RL 32-3MAF Quantity of compressor oil 0.99...
  • Page 14: Performance Data Aero Slm 3-11 Acc. To En 14511 - Heating

    1 24 Air-inlet temperature [°C] Heat output 7 76 7 02 6 61 6 32 5 65 4 80 Power intake 2 19 2 21 2 36 2 41 2 36 2 26 (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 15: Performance Data Aero Slm 3-11 Acc. To En 14511 - Cooling

    All 3 requirements must be fulfi lled independently. This is possible applying the NAVIGATOR Pro. The entire distribution system has to fulfi ll the 3 mentioned requirements. To ensure a large cooling demand, the cooling limit has to be set as high as possible. (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 16 3. Description description Heat output AERO SLM 3-11 at fl ow temperature 35°C NOMINAL Air-inlet temperature [°C] Heat output AERO SLM 3-11 at fl ow temperature 45°C NOMINAL Air-inlet temperature [°C] (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 17 Heat output AERO SLM 3-11 at fl ow temperature 55°C NOMINAL Air-inlet temperature [°C] Heat output AERO SLM 3-11 at nominal speed Air-inlet temperature [°C] (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 18: Performance Data Aero Slm 6-17 Acc. To En 14511 - Heating

    3 .12. Per fo r m an c e d at a AE R O SL M 6- 17 acc. t o E N 1 451 1 - he at i ng (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 19: Performance Data Aero Slm 6-17 Acc. To En 14511 - Cooling

    6 14 6 15 6 19 6 24 [kW] 1 94 1 60 1 32 1 08 0 88 0 74 3 11 3 81 4 65 5 70 7 01 8 48 (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 20 3. Description description Heat output AERO SLM 6-17 at fl ow temperature 35°C [°C] Heat output AERO SLM 6-17 at fl ow temperature 45°C [°C] (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 21 Heat output AERO SLM 6-17 at fl ow temperature 55°C [°C] Heat output AERO SLM 6-17 at nominal speed [°C] (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 22: Filling Quantities Refrigerant

    For pipe length more than 6 m, the following refrigerant quantities must be refi lled. AERO SLM 3-11 Refrigerant re-fi ll quantity AERO SLM 3-11 HGL Refrigerant re-fi ll quantity AERO SLM 6-17 HGL (C) IDM ENERGIESYSTEME GMBH...
  • Page 23: Maximum Heigth Difference

    3 . 16. Limi ts of u se The heating of other fl uids as heating water is not permitted with the AERO SLM 3-11 and AERO SLM 6-17 (for heating water quality, see page 44). Heat pumps are by nature subjects to limits of use regarding of pressure and temperature (see diagram).
  • Page 24 3. Description description AERO SLM 3-11 and 6-17 - Heating [°C] R410A 35 40 [°C] outdoor temperature The minimum heat pump fl ow temperature is the lowest temperature that the heat pump can produce (depending on the heat source temperature) and is then switched off at this value. Due to the hydraulic spread across the heat pump, the control-related switching hysteresis and the humidity-dependent dew point, it is not possible to reach this temperature in the cooling circuit.
  • Page 25: Transport

    fi xing screws must be loosen. After that the cover can be unhinged and removed. Loosen the fi xing screws on the outdoor unit When transporting, the AERO SLM may not be tilted more than 30°! (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 26: Assembly And Hydraulic Installation

    The connections for the heating supply and return are 2. impact sound insulation 3. screed located inside the housing and can be led out either 4. recess on the right or left side of the heat pump. (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 27: Installation Of Connecting Hoses

    The fi xing screws are located on the front as shown crosswise and not cut out completely. in the photo below. Cut in the rubber gromments Then the grommets are mounted in the bushing du- ring the installation of the connecting hoses. (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 28 Now the connecting hoses can be connected as described as followed. Where the connection hoses are mounted is specifi ed with stickers inside the heat pump. Fully assembled connecting hoses AERO SLM 3-11 Connection HGL pipe (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 29: Assembly Of Outdoor Unit

    If the alignment is not possible at very windy loca- tions, additional wind protection can be installed, e.g. a hedge. (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 30: Installation Variant Of The Outdoor Unit

    Air heat pumps are producing condensation water during operation. This could be 6 liters per defrost cycle within 2 minutes. The condensate run-off must be frost-proof. (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 31: Assembling Of The Outdoor Unit On Concrete Base

    Connection for the equipotential bonding or lightning protection AERO SLM 3-11 Mounting of the outdoor unit AERO SLM 3-11 Mounting of the outdoor unit AERO SLM 6-17 Connection for the equipotential bonding or lightning protection...
  • Page 32: Condensation Run-Off

    The heating band (2 m) will be placed in the drain hose. The condensation bin and the run- off have to be checked for soiling regularly The minimum distances must be maintained due to perform maintenance. (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 33: Connection Of The Refrigerant Circuit

    The soldered connections must be made according to the requirements of the cooling technology by a To avoid buckles in the refrigerant pipes, the minimum trained refrigeration engineer licensed by IDM-Ener- bend radius must be observed. To prevent embritt- giesysteme GmbH.
  • Page 34: Connection Of The Indoor Unit On Refrigerant Side

    The refrigerant pipes will be soldered to the indoor unit. The soldered connections must be made accor- ding to the requirements of the cooling technology by a trained refrigeration engineer licensed by iDM Energiesysteme GmbH. The connections for the refrigerant pipes are on the backside of the AERO SLM indoor unit.
  • Page 35: Wall Opening

    PVC pipe. rised by iDM Energiesysteme GmbH. After completing the installation the wall opening The refrigerant fl ow through the indoor unit can lead to must be sealed on site using a suitable sealing mass fl...
  • Page 36: Electrical Assembly

    When working on the heat pump, please be sure that the device is tensionless. The design of the residual current circuit breaker depends on the heat pump type and power rating! (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 37: Electrical Connection Of Outdoor Unit

    If the front part AERO SLM 3-11 must be removed in case of maintenance, there may be damages to the connections of the control unit or the main board by careless and rapid remove.
  • Page 38: Disassembly The Cover

    When removing the panel, the connecting cable should not be exposed to tensile stress. To comple- tely remove the panel, the connection cable on the Disconnect the cable to the control panel central unit must be unplugged. (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 39: Central Unit Of Control

    113 114 115 116 117 118 119 120 121 122 123 Extension module external / Cascade participant EEV2 X4 EEV1 X2 RS232 X36 LAN X33 132 131 130 - SH Touchdisplay Extension module internal (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 40: Sensor Design

    The sensor positions are shown in the relevant instal- NAVIGATOR Pro additional board lation diagram. To use the iDM single-room control, an additional The position of the sensors are shown in the relevant board must be connected to the touch display of NA- hydraulic scheme of the heat pump.
  • Page 41: Commissioning

    R410A) should be checked and the set shut-off If an error occurs several times in succes- temperature changed if necessary. sion, please contact your relevant iDM - If the heat pump is to be drained on the heating customer service department.
  • Page 42: Hydraulic Diagrams

    9 .1. A ERO S LM w i t h di rec t h ea t in g c ir cu it , H y gi e nik 2 . 0 w i t ho u t s e par at i o n pl at e (C) IDM ENERGIESYSTEME GMBH...
  • Page 43: Aero Slm With Mixed Circuit, Hygienik 2.0 With Separation Plate

    9 . 2. A ERO S LM w it h m i xe d c irc u it , H yg ie ni k 2. 0 w i t h s e pa r at i o n pla t e Installation instructions AERO SLM (C) IDM ENERGIESYSTEME GMBH...
  • Page 44: Heating Side Installation

    The system must only be connected to the mains and put into operation if the entire heating system has been fi lled and bled, as otherwise the circulating pumps may run dry. (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 45: Declaration Of Confirmity, Product Fiche

    11. Declaration of confirmity, Product fiche declaration of confirmity, product fiche (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 46 [%] energy efficiency class of package IDM-Energiesysteme GmbH A-9971 Matrei i.O., Seblas 16 – 18, Telefon +43 (0)4875 6172-0 Firmenbuch.Nr. 44919h, LG Innsbruck, Firmensitz: 9971 Matrei i.O., UID-Nr.: ATU 433 604 02 (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 47 [%] energy efficiency class of package IDM-Energiesysteme GmbH A-9971 Matrei i.O., Seblas 16 – 18, Telefon +43 (0)4875 6172-0 Firmenbuch.Nr. 44919h, LG Innsbruck, Firmensitz: 9971 Matrei i.O., UID-Nr.: ATU 433 604 02 (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 48: Technical Documentation

    12. Technical documentation 12. Technical documentation technical documentation (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 49 (C) IDM ENERGIESYSTEME GMBH Installation instructions AERO SLM...
  • Page 50 PRACTICAL KNOWLEDGE FOR SALES AND TECHNOLOGY The comprehensive range of seminars for sp ecialists at the IDM POWER FA MILY is available to you any time on our websit. We look for ward to re ceiving your re gist ration.

Table of Contents