Advertisement
Quick Links
Installation
Locate the Encoder with the remote source. Install CAT-5
or CAT-5e cable between the remote source location and
the system controller, up to 300 feet (90 m).
Crimp an RJ-45 connector on the source end of the CAT-
5 cable, following the T568A standard as shown. Plug
the connector into the RNET A/V jack on the Encoder. (If
desired, use modular wall plates and RJ-45 patch cables
for a neater appearance. Punch down the CAT-5 per the
T568A standard and use a straight-through patch cable
between the Encoder and the wall plate.)
RJ-45 Using T568A
Wiring Standard
Setup for RNET Control
Note: For RNET control of the remote source, both the
source equipment and the system controller must be
RNET capable. If the RNET controller does not have an
RNET A/V jack, you will need to use an RAVD1 Decoder
at the controller to receive signals from the Encoder.
1. Connect RNET source equipment. Using the sup-
plied RJ-45 patch cable, connect from an RNET Link jack
on the source equipment to the RNET Link jack on the
Encoder. Use the supplied RCA patch cable to connect
from the source equipment’s audio and video outputs to
the Encoder’s inputs.
2. Connect Encoder to RNET system. Crimp an RJ-45
connector on the system end of the CAT-5 cable, follow-
ing the T568A standard as shown. With the RNET system
turned off, plug the connector into the RNET A/V source
input jack on the RNET system controller or RAVD1
Decoder. (If using a wall plate, punch down the CAT-5 per
the T568A standard and use a straight-through patch
cable between the system and the wall plate.)
Note: Do not plug the CAT-5 cable into an RNET Link
jack. It must be plugged into an RNET A/V jack on
either the system controller or the RAVD1 Decoder.
3. Connect Decoder to RNET system. If using an
RAVD1 Decoder, use a straight-through RJ-45 patch
cable to connect from either RNET Link jack on the
Decoder to any unused RNET Link jack on the system or
an RNET source component. Use RCA patch cables to
connect from the Decoder’s audio and video outputs to
inputs on the RNET system controller.
Note: Do not connect the Decoder’s IR input. Doing so
will disable RNET for the entire system.
Setup for IR Control
Note: If the system controller does not have an RNET
A/V jack, you will need to use an RAVD1 Decoder at
the controller to receive signals from the Encoder.
1. Connect source equipment. Attach an IR emitter
to the infrared sensor on the source equipment and plug
the emitter into the IR OUT jack on the Encoder. (Or use
an IR link cable or mono patch cable with 1/8-inch [3.5
mm] TS connectors to connect from the Encoder to the
source equipment’s IR input jack.) Use the supplied RCA
patch cable to connect from the source equipment’s
audio and video outputs to the Encoder’s inputs.
2. Connect Encoder to multiroom system. Crimp an
RJ-45 connector on the system end of the CAT-5 cable,
following the T568A standard as shown. With the system
turned off, plug the connector into the RNET A/V jack on
the system controller or RAVD1 Decoder. (If using a wall
plate, punch down the CAT-5 per the T568A standard
and use a straight-through patch cable between the
system and the wall plate.)
Note: Do not plug the CAT-5 cable into an RNET Link
jack. It must be plugged into an RNET A/V jack on
either the system controller or the RAVD1 Decoder.
3. Connect Decoder to system. If using an RAVD1
Decoder, use RCA patch cables to connect from the
Decoder’s outputs to source inputs on the system.
RNET system. Use a straight-through RJ-45 patch cable
to connect from either RNET Link jack on the Decoder
to any unused RNET Link jack on the system or an RNET
source component.
Note: Do not connect the Decoder’s IR input. Doing so
will disable RNET for the entire system.
Non-RNET system. Use an IR link cable or mono patch
cable with 1/8-inch (3.5 mm) TS connectors to connect
from the system’s IR output to the Decoder’s IR input.
Final Steps
1. Power Encoder. Plug the power supply into an AC
power receptacle and connect its output lead to the
power jack on the Encoder. If using an RAVD1 Decoder,
power it up as well.
2. Turn on source and system. Power up the remote
source and the system. Select the remote source at a
system keypad or touchscreen and begin playing the
source. You should hear it playing through the system.
3. Program multiroom system. Follow the multiroom
system’s programming instructions to set up the remote
source for control from the keypads and touchscreens.
Specifi cations
RNET A/V connector: 8-pole modular RJ-45 jack
Input connectors: (1) composite video RCA jack
(2) left and right audio RCA jacks
IR emitter connector: 2-pole 0.125” (3.5 mm) TS jack
RNET Link connector: 8-pole modular RJ-45 jack
Power requirement: 12 VDC 1 A (power supply included)
Mounting method: Surface
Dimensions: 4.25” W x 1.82” H x 2.5” D
(10.8 x 4.6 x 6.4 cm)
Weight: 10.0 oz (284 g)
Warranty
The Russound RAVE1 is fully guaranteed against all defects in materials
and workmanship for two (2) years from the date of purchase. During this
period, Russound will replace any defective parts and correct any defect in
workmanship without charge for either parts or labor. For this warranty to
apply, the unit must be installed and used according to its written instruc-
tions. If service is necessary, it must be performed by Russound. The
unit must be returned to Russound at the owner’s expense and with prior
written permission. Accidental damage and shipping damage are not con-
sidered defects, nor is damage resulting from abuse or from servicing by
an agency or person not specifi cally authorized in writing by Russound.
This warranty does not cover: damage caused by abuse, accident, mis-
use, negligence, or improper installation or operation; power surges and
lightning strikes; normal wear and maintenance; products that have been
altered or modifi ed; any product whose identifying number, decal, serial
number, etc. has been altered, defaced or removed.
Russound sells products only through authorized dealers and distributors
to ensure that customers obtain proper support and service. Any Rus-
sound product purchased from an unauthorized dealer or other source,
including retailers, mail order sellers and online sellers will not be honored
or serviced under existing Russound warranty policy. Any sale of products
by an unauthorized source or other manner not authorized by Russound
shall void the warranty on the applicable product.
Damage to or destruction of components due to application of excessive
power voids the warranty on those parts. In these cases, repairs will be
made on the basis or the retail value of the parts and labor. To return for
repairs, the unit must be shipped to Russound at the owner’s expense,
along with a note explaining the nature of service required. Be sure to pack
the unit in a corrugated container with at least three (3) inches of resilient
material to protect the unit from damage in transit.
Before returning a unit for repair, call Russound at 603.659.5170 for a
return authorization number. Write this number on the shipping label and
ship to: Russound, 5 Forbes Road, Newmarket, NH 03857.
5 Forbes Road, Newmarket NH 03857 USA
Tel 603.659.5170 • Fax 603.659.5388
www.russound.com
Copyright © 2007 Russound. All rights reserved. All trademarks are the
property of their respective owners. Specifi cations are subject to change
without notice. Russound is not responsible for typographical errors or
omissions.
28-1264 06/05/07
RAVE1
RNET A/V Encoder
Instruction Manual
Overview
The RAVE1 RNET A/V Encoder enables the use of a re-
mote source with a Russound RNET
®
or other multiroom
audio-video system. It connects to the source equipment
and sends audio and video signals to the multiroom
system over a single CAT-5 cable. It also provides either
RNET or infrared control of the source equipment.
Housed in a compact surface-mount metal box, the
RAVE1 provides connectors for RNET Link, IR emitter,
stereo audio, and composite video. A special RJ-45 jack
connects through the CAT-5 cable to either an RAVD1
RNET A/V Decoder or an RNET A/V-enabled multiroom
controller at the system end.
The RAVE1 comes with a 12 VDC power supply and
patch cables for connecting to the source equipment.
Features
• Enables remote location of an audio-video source for a
multiroom system
• Provides RNET control and feedback with an RNET
remote source and multiroom system
• Provides IR control of a non-RNET remote source
• Connects to the multiroom system with a single CAT-5
cable
• Easily mounts on any fl at surface
Advertisement
Related Manuals for Russound RAVE1
Summary of Contents for Russound RAVE1
- Page 1 Overview plate, punch down the CAT-5 per the T568A standard unit must be returned to Russound at the owner’s expense and with prior written permission. Accidental damage and shipping damage are not con- and use a straight-through patch cable between the...
- Page 2 (up to 300 feet) plug is damaged, liquid has been spilled or objects have fallen into the apparatus, or the apparatus has Note: The RAVE1 provides either RNET or IR been exposed to rain or moisture, does not operate RNET A/V Encoder control of the source.