Sanyo VCC-WD8874 - Wide Dynamic Range Color Instruction Manual

English Français
VCC-WD8875P
INSTRUCTION MANUAL
VCC-WD8874
Wide Dynamic Range Camera
About this manual
• Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for later reference.
• This manual covers two models. Any difference between the two models is
indicated when necessary.
iridix technology is provided by Apical Limited, UK.
PREPARATION
b Lens attachment
The camera has a mount for the CS mount lens.
Apply adapter ring (sold separately) when you use
any C mount lens.
5 mm/0.2 in. max.
LENS terminal for auto iris lens
Brake coil (+) Brake coil (–)
Drive coil (–) Drive coil (+)
Depending on the type of the lens, the shape of the lens plug may differ. In
this case, consult your dealer or an Authorized Sanyo Service Center.
b Camera attachment
Install the camera in a correct location so that the intended object
can be monitored properly.
You should also adjust on the monitor side.
• Depending on the conditions of use, installation and
environment, please be sure to make the appropriate settings
and adjustments. If you need help with installation and/or
settings, please consult your dealer or an Authorized Sanyo
Service Center.
• If you want to use a commercially available platform for the
camera, select an appropriate type, taking into consideration the
gross weight of the camera and platform, and secure it on a firm
place.
• Images may blur under extremely bright lighting; adjust the
lighting angle to get clear images.
B
A
B
A
A Bracket screws (longer) B Camera screws (shorter)

SPECIFICATIONS

Scanning system : VCC-WD8875P:
PAL standard 625 lines, 50 fields/sec.
VCC-WD8874:
NTSC standard 525 lines, 60 fields/sec.
Image sensor : 1/3" progressive CMOS
Number of effective pixels : 800 (H) x 600 (V)
Horizontal resolution : 550 TV lines typical
Minimum illumination : Gain high: 0.8 lx (F1.2, color mode)
0.08 lx (F1.2, B/W mode)
: 1.0 V(p-p)/75 Ω, composite, BNC
Video output
Video S/N ratio : More than 48 dB (AGC off: More than 50 dB)
Light control : Optical auto iris lens/Electronic iris (indoor use)
Auto iris lens drive : DC
Lens mount : CS mount
Flange back : 12.5 mm ± 0.5 mm / 0.5 in. ± 0.02 in. adjustment
Menu : On screen display
Wide dynamic range : ON (65 dB typical)/OFF
Backlight compensation : OFF/ON (Center zone metering)
White balance : ATW/Manual
Gain control : Normal/High/OFF
Electronic shutter : VCC-WD8875P:
1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 sec.
VCC-WD8874:
1/60, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 sec.
Aperture compensation : Normal/High/Low/OFF
Day/Night : Auto / Color / B/W
Sync system : Internal sync/Line lock
Camera title : OFF/ON, Up to 16 characters, adjustable title position
Digital noise reduction : ON (1, 2)/OFF
Operating environment : Temperature: -10°C - +50°C (14°F - 122°F)
Humidity: less than 90 % RH (no condensation)
Power supply : VCC-WD8875P: 24 V AC ±10%, 50 Hz/ 12 - 15 V DC
VCC-WD8874: 24 V AC ±10%, 60 Hz/ 12 - 15 V DC
Power consumption : Approx. 6.9 W (with auto-iris lens)
Weight : Approx. 330 g (11.6 oz.) (without lens)
b DIMENSIONS
129 (5.1)
1
(0.04)
119.5 (4.7) 71 (2.8)
1/4"-20UNC
Unit: mm (inch)
Appearance and specifications are subject to change without prior notice
or obligations.
b Flange-back adjustment
This normally does not need adjustment. If the picture is out of focus at
the telephoto position, adjust the flange-back position as described
below.
1 4
3
2
1
Loosen.
2
Set to the maximum telephoto position and focus the picture.
3
Set to the maximum wide-angle position and focus the picture.
• Repeat steps 2 and 3 until the image stays in-focus when changing
from a wide-angle position to a telephoto position.
4
Tighten.
PRECAUTIONS
■ In case of a problem
Do not use the unit if smoke or a strange odor comes from the unit,
or if it seems not to function correctly. Turn off the power
immediately and disconnect the power cord, and then consult your
dealer or an Authorized Sanyo Service Center.
■ Do not open or modify
Do not open the cabinet, as it may be dangerous and cause damage
to the unit. For repairs, consult your dealer or an Authorized Sanyo
Service Center.
■ Do not put objects inside the unit
Make sure that no metal objects or flammable substance get inside
the unit. If used with a foreign object inside, it could cause a fire, a
short-circuit or damage. Be careful to protect the unit from rain, sea
water, etc. If water or liquid gets inside the unit, turn off the power
immediately and disconnect the power cord, and then consult your
dealer or an Authorized Sanyo Service Center.
■ Be careful when handling the unit
To prevent damage, do not drop the unit or subject it to strong shock
or vibration.
■ Do not install this unit close to magnetic fields
The magnetic fields may result in unstable operation.
■ Protect from humidity and dust
To prevent damage, do not install the unit where there is greasy
smoke or steam, where the humidity may get too high, or where
there is a lot of dust.
■ Protect from high temperatures
Do not install close to stoves, or other heat sources, such as
spotlights, etc., or where it could be subject to direct sunlight, as this
could cause deformation, discoloration or other damages.
Be careful when installing close to the ceiling, in a kitchen or boiler
room, as the temperature may rise to high levels.
■ Cleaning
• Dirt can be removed from the cabinet by wiping it with a soft cloth.
To remove stains, wipe with a soft cloth moistened with a soft
detergent solution and wrung dry, then dry by wiping with a soft
cloth.
• Do not use benzine, thinner or other chemical products on the
cabinet, as this may cause deformation and paint peeling. Before
using a chemical cloth, make sure to read all accompanying
instructions. Make sure that no plastic or rubber material comes
into contact with the cabinet for a long period of time, as this may
cause damage or paint peeling.
SERVICE
The camera is a precision instrument. Handle it carefully and always
follow the safety precautions. If the camera requires service, never
try to repair it yourself or open the casing.
For servicing, maintenance, or repairs, consult your dealer or an
Authorized Sanyo Service Center.
For US and Canadian Users
Safety Guard
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THIS UNIT.
WARNING:
TO REDUCE A RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
For the customers in Canada
This Class B digital apparatus complies with Canadian ICES/NBM-003.
This installation should be made by a qualified service person and should
conform to all local codes.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Changes or modifications not expressly approved by Sanyo may void the user's
authority to operate this camera.
For EU Users
Please note:
Your SANYO product is designed and manufactured
with high quality materials and components which
can be recycled and reused.
This symbol means that electrical and electronic
equipment, at their end-of-life, should be disposed
of separately from your household waste.
Please dispose of this equipment at your local
community waste collection/recycling centre.
In the European Union there are separate collection
systems for used electrical and electronic products.
Please help us to conserve the environment we live
in!
This symbol mark and recycle system are
applied only to EU countries and not applied
to countries in other areas of the world.
SANYO FISHER Sales (Europe) GmbH
Stahlgruberring 4, D-81829 München, Germany
SANYO Electric Co., Ltd.
1-1, Sanyo-cho, Daito City, Osaka 574-8534, Japan
For Russian Users
This product is certified by an official certification
company which is authorized by the Russian Federation.
ДЛЯ ПОЛЬЗОВАТЕЛЕЙ РОССИЯ
Данная продукция сертифицирована официальным
органом по сертификации Российской Федерации.
SANYO Electric Co., Ltd.
1AC6P1P3382--
L5CU2/XE, US (1108KP-HS) Printed in China