Setting Up The System - Denon AVR-2805 Operating Instructions Manual

7

SETTING UP THE SYSTEM

• Once all connections with other AV components have been completed as described in "CONNECTIONS"
(see pages 5 to 9), make the various settings described below on the monitor screen using the AVR-2805's
on-screen display function.
These settings are required to set up the listening room's AV system centered around the AVR-2805.
Use the following buttons to set up the system
• Use the following buttons to set up the system.
1
Check that the remote control unit set to AMP mode. (TAPE, CDR/MD, CD)
2
• System setup items and default values (set upon shipment from the factory)
1. Auto Setup/Room EQ
Auto Setup/Room EQ
Set this to switch the surround
Power Amp
1
Auto Setup back channel's power amplifier
Assignment
for use for zone2.
This parameter is for optimizing the Room EQ with
Manual EQ
2
which the audio signals are produced from the
Setup
speakers.
Room EQ Set the Room EQ setting with All or Assign for
3
Setup each surround mode.
Direct Mode Set the ON/OFF setting of Room EQ, in the case of
4
Setup the surround mode is in Direct or Pure Direct.
Mic Input Set this to switch the Mic Input jack for use for Mic
5
Select or V.Aux L-channel input jack.
(Remote control unit)
SYSTEM SETUP button
Press this to display the system setup menu.
CURSOR buttons
Use these to move the cursors the left, right, up and
down on the screen.
ENTER button
Press this to switch the display.
Also use this button to complete the setting.
Default settings
SURROUND BACK
All Channel and Frequency=0 dB
All
OFF
Mic
2. Speaker Setup
Speaker Setup
Input the combination of speakers in your
system and their corresponding sizes (SMALL for
Speaker regular speakers, LARGE for full-size, full-range) to
1
Configuration automatically set the composition of the signals
output from the speakers and the frequency
response.
This parameter is for optimizing the timing with
which the audio signals are produced from the
2
Delay Time
speakers and subwoofer according to the listening
position.
This adjusts the volume of the signals output from
Channel
3
the speakers and subwoofer for the different
Level
channels in order to obtain optimum effects.
Set the frequency (Hz) below which the bass so of
Crossover
4
the various speaker is to be output from the
Frequency
subwoofer.
Subwoofer This selects the subwoofer speaker for playing
5
Mode deep bass signals.
3. Input Setup
Input Setup
Input
source
Digital In This assigns the digital input jacks for the
1
Assignment different input sources.
Digital
Inputs
Ext. In
Set the Ext. In Subwoofer terminal playback
2
Subwoofer
level.
Level
Component This assigns the color difference (component)
3
In Assign video input jacks for the different input sources.
Video Input Set the input signal to be output from the monitor
4
Mode output terminal.
Auto Tuner FM stations are received automatically and stored
5
Presets in the memory.
Default settings
Surround Back
Front Sp. Center Sp. Subwoofer Surround Sp.
Large Small Yes Small Small / 2spkrs
Front L & R Center Subwoofer Surround L & R
3.6 m (12 ft) 3.6 m (12 ft) 3.6 m (12 ft) 3.0 m (10 ft)
Surround Surround Surround Surround
Front R Center
Front L
L R Back L Back R
0 dB 0 dB 0 dB 0 dB 0 dB 0 dB 0 dB
80Hz
LFE
Default settings
CD DVD VDP TV DBS V. AUX VCR-1 VCR-2
COAX1 COAX2 OPT1 OFF OPT2 OPT5 OPT3 OFF
Subwoofer = +15 dB
VDP TV DBS VCR-1 VCR-2 V. AUX
DVD
VIDEO VIDEO VIDEO
NONE NONE NONE NONE
1 2 3
AUTO
A1 ~ A8 87.5/89.1/98.1/108.0/90.1/90.1/90.1/90.1 MHz
B1 ~ B8
522/603/999/1404/1611 kHz, 90.1/90.1/90.1 MHz
C1 ~ C8 90.1 MHz
D1 ~ D8 90.1 MHz
E1 ~ E8 90.1 MHz
F1 ~ F8 90.1 MHz
G1 ~ G8 90.1 MHz
ENGLISH
Sp.
SBL & SBR
3.0 m (10 ft)
Subwoofer
0 dB
CDR/
TAPE
OPT4
— —
— —
11