HP 252663-B24 - PDU Power Distribution Strip Installation Instructions Manual

Modular power distribution unit kit installation instructions

Advertisement

HP Modular Power Distribution
Unit Kit
Installation Instructions
© Copyright 2006, 2008 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only
warranties for HP products and services are set forth in the express warranty
statements accompanying such products and services. Nothing herein should
be construed as constituting an additional warranty. HP shall not be liable for
technical or editorial errors or omissions contained herein.
Part Number 240824-4 2
0
October 2008 (Tenth Edition)
Overview
These installation instructions are provided to assist qualified
personnel with the installation of the HP Modular Power Distribution
Unit (mPDU) Kit.
The input voltage of a single phase mPDU is either 100 to 127 VAC
or 200 to 240 VAC, depending on the model.
The input voltage of a three phase mPDU is 200 to 240 VAC, phase-
phase or phase-neutral, depending on the model.
The control unit (if included) provides the following features:
Flexible mounting in 0U or 1U configurations, maximizing rack
space (no additional parts are required for mounting)
Overcurrent and short-circuit protection for each output (UL-
489-listed circuit breakers)
Manual on/off control for each of the output load groups
Pilot light for main AC input (depending on the model)
IEC-320 C19 outlets to power extension bars or other IEC-320
C20 plug-compatible equipment
Easy identification and reset of overload circuits (circuit
breakers move to Off position), minimizing downtime
Power cord retention
Recessed handles to prevent inadvertent power-off
The extension bars (if included) provide the following features:
Multiple power outlets, conveniently located for quick and easy
equipment power connections
Lighted main power indicator
Attached 2-m (6-ft) input power cords
Power cord retention and power cord labeling
Modular PDU models
To view the most recent modular PDU information, see the HP
website (http://www.hp.com/go/rackandpower).
From there, you can navigate to the appropriate page by following
the steps below.
1.
Click Power infrastructure.
2.
Click Power distribution units.
3.
Click Modular.

Advertisement

Table of Contents
loading

Summary of Contents for HP 252663-B24 - PDU Power Distribution Strip

  • Page 1 Click Power infrastructure. Click Power distribution units. Click Modular. © Copyright 2006, 2008 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
  • Page 2: Important Safety Information

    Important safety information WARNING: To reduce the risk of personal injury from high-leakage current, verify earth connection before connecting the power supply. The summation of input power for multiple pieces of information technology equipment through the use of power products can result in high-leakage currents. If the total system leakage current for a system of components exceeds 3.5 mA: •...
  • Page 3: Required Tools

    Cord retention bracket (1) Model Number Number of Number of Number single/double extension Jumper cords in the high-voltage model kits (2) extension brackets bar power control -or- bars cord unit tie • Control unit retention wraps bands 0U mounting brackets (2) AF512A 1U mounting brackets (2) Cord retention bracket (1)
  • Page 4 Installing the 0U brackets Installing the 1U brackets...
  • Page 5 Installing the control unit in the rack The control unit can be mounted in the rack two different ways, depending on whether you install the 0U brackets (A) or the 1U brackets (B) to the control unit. Installing the extension bars (if included) The cord retention brackets are shown for clarification in the Installing the control unit in a square-holed...
  • Page 6 Installing the extension bars using single stick mounting brackets Connecting and securing the power cords...
  • Page 7: Connecting Devices

    Connecting the ground bonding Control Total rating of Outlet Load Individual cable unit control unit style outlet rating rating NOTE: This section is only applicable if a control unit was 228481- 24 A IEC 320- 15 A 12 A shipped as part of your kit. 228481- 24 A IEC 320-...

This manual is also suitable for:

252663-b31 - high voltage modular power distribution unit zero-u/1u stripEo4500Eo4501Eo4502Eo4503Eo4504 ... Show all

Table of Contents