Loop Out Setting; Id Number Setting - NEC PlasmaSync 42VP4D User Manual

Loop Out setting

When this feature is set to ON, the received signal will be
looped out.
Example: Setting "ON"
Set "ADVANCED OSM" to "ON" in the main menu (1/
2), then perform the following operations.
Press the MENU/ENTER button on the remote control to
display the MAIN MENU on the screen, then...
1. Use the and buttons to select "OPTION3", then
press the MENU/ENTER button.
The "OPTION3" screen appears.
2. Use the and buttons to select "LOOP OUT".
3. To set the LOOP OUT to "ON"...
Use the and buttons to select "ON".
The mode switches as follows each time the
button is pressed:
OFF ON
OPTION3
PREVIOUS PAGE
TIMER
PWR. ON MODE
CONTROL LOCK
IR REMOTE
LOOP OUT
ID NUMBER
VIDEO WALL
SEL. ADJ.
4. Once the setting is completed...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once
more.
Information
LOOP OUT settings
ON ...... The received signal will be looped out via PC1
terminal or VIDEO1 terminal.
OFF .... The received signal will not loop out.
* Even if LOOP OUT is ON, signals won't be sent out if
POWER is being turned off.
To connect another display...
See page E-11.
If the RGB/PC1 signal is present at the time
the power switched on...
The RGB/PC1 input will be displayed regardless of the
setting of LOOP OUT.
Restoring the factory default settings
Select "ALL RESET" under the OPTION1 menu. Note
that this also restores other settings to the factory
defaults.

ID number setting

When using more than one of these displays, this function
sets ID numbers so that operation of the remote control
does not cause multiple monitors to operate at the same
time.
Example: Setting "2"
Set "ADVANCED OSM" to "ON" in the main menu (1/
2), then perform the following operations.
Press the MENU/ENTER button on the remote control to
display the MAIN MENU on the screen, then...
or
3 / 3
: LAST
: OFF
: ON
: ON
: ALL
EXIT RETURN
E-36
1. Use the and buttons to select "OPTION3", then
press the MENU/ENTER button.
The "OPTION3" screen appears.
2. Use the and buttons to select "ID NUMBER".
3. To set the ID NUMBER to "2"...
Use the and buttons to select "2".
The mode switches as follows each time the
button is pressed:
ALL 1 2 .....
OPTION3
PREVIOUS PAGE
TIMER
PWR. ON MODE
CONTROL LOCK
IR REMOTE
LOOP OUT
ID NUMBER
VIDEO WALL
SEL. ADJ.
* To reset back to ALL
Press the CLEAR button
4. Once the setting is completed...
Press the EXIT button to return to the main menu.
To delete the main menu, press the EXIT button once more.
Information
ID NUMBER settings
ALL ........... ID NUMBER will not be set.
1 to 256 .... ID NUMBER will be set.
When the ID NUMBER have been set
You can also set ID NUMBER for each remote control to
operate the plasma display individually. To do so, see below.
Restoring the factory default settings
Select "ALL RESET" under the OPTION1 menu. Note
that this also restores other settings to the factory
defaults.
To set the ID number for the remote control
Example: Setting "2"
1. Press the ID SELECT button on the remote control.
The "ID SELECT" screen appears.
2. Use the and buttons to select "ID NUMBER".
3. To set the ID NUMBER to "2"...
Use the and buttons to select "2".
The mode switches as follows each time the
button is pressed:
ALL 1 2 .....
ID SELECT
POSITION :
ID NUMBER
ADJ.
* To reset back to ALL
Press the CLEAR button
4. Once the setting is completed...
Press the EXIT button to delete the ID SELECT screen.
or
255 256
3 / 3
: LAST
: OFF
: ON
: OFF
: 2
EXIT
RETURN
or
255 256
1
: 2
EXIT RETURN