Table of Contents
Advertisement
S
M
The FT-60R Set Mode, already described in parts of many previous chapters, is easy to
activate and set. It may be used for configuration of a wide variety of transceiver param-
eters, some of which have not been detailed previously. Use the following procedure to
activate the Set Mode:
1. Press the [ F/W ] key, then press the [ 0 (
2. Rotate the DIAL knob to select the Set Mode Item to be ad-
justed.
3. Press the [ F/W ] key momentarily to enable adjustment of the
Set Mode Item.
4. Rotate the DIAL knob to adjust or select the parameter to be
changed on the Set Mode Item selected in above step.
5. After completing your selection and adjustment, press the PTT switch momentarily to
save the new setting and exit to normal operation.
1) Some Set Mode Items (like Set Mode Item 50: TN FRQ) require that the
[ F/W ] key be pressed after setting of the parameter, and before exiting to
normal operation.
2) Two Set Mode Item numbers (In the factory default, Set Mode Item 29: PAGER, and
46: SKIP) will blink while selecting the Set Mode Item; this indicates that this Set Mode
Item has been assigned to the [ 7 ( P1 )] or [ 8 ( P2 )] key of the keypad.
S
M
I
F
1 [ APO ]
Setting of the Automatic Power-Off feature.
2 [ AR BEP ]
Selects the Beep option during ARTS operation.
3 [ AR INT ]
Selects the Polling Interval during ARTS operation.
4 [ ARS ]
Enables/Disables the Automatic Repeater Shift function.
5 [ BCLO ]
Enables/Disables the Busy Channel Lock-Out feature.
6 [ BEEP ]
Enables/Disables the beeper.
7 [ BELL ]
Selects the number of CTCSS/DCS Bell ringer repetitions.
8 [ BSY.LED ]
Enables/Disables the BUSY LED while the Squelch is open.
9 [ CLK.SFT ]
Shifting of the CPU clock frequency.
10 [ CWID ]
Enables/disables the CW identifier during ARTS operation.
11 [ CW WRT ]
Programs and activates the CW Identifier.
12 [ DC VLT ]
Indicates the DC Supply Voltage.
13 [ DCS.COD ]
Setting of the DCS code.
14 [ DCS.N/R ]
Enables/Disables "Inverted" DCS code decoding.
15 [ DT DLY ]
Setting of the DTMF Autodialer Delay Time.
16 [ DT SPD ]
Setting of the DTMF Autodialer Sending Speed.
17 [ DT WRT ]
Programming of the DTMF Autodialer.
18 [ EAI ]
Enables/Disables the Emergency Automatic ID (EAI) Feature.
19 [ EDG.BEP ]
Enables/Disables the Band-edge beeper while selecting the
frequency via the DIAL knob.
66
M
) SET ] key to enter the Set mode.
FT-60R O
A
V
( D
)
: B
I
OFF / 0.5H - 12.0 H
INRANG / ALWAYS / OFF
25 SEC / 15 SEC
ARS. ON / ARS.OFF
BCL. ON / BCL.OFF
KEY+SC / KEY / OFF
OFF / 1T / 3T /
5T / 8T / CONT
LED. ON / LED.OFF
SFT.OFF / SFT. ON
TX OFF / TX ON
---
---
104 DCS codes (023)
T/RX N, RX R,
TX R, T/RX R
50MS / 100MS / 250MS /
450MS / 750MS / 1000MS
50MS / 100MS
---
INT. 1M - INT. 50M /
CON. 1M - CON.50M / OFF
BEP.OFF / BEP. ON
M
Advertisement
Table of Contents
