Universal Remote Control UR3-EXP Operating Instructions

Operating Instructions
1 Introduction
The remote control is designed to operate the
For 3 Function
Scientific-Atlanta Explorer 2000 and 3000
Series and the Pioneer Voyager set top boxes
Cable Remote Control
and the majority of TV and VCR/DVD equipment
on the market.
UR3-EXP
2 Replacing Batteries
Before you program or operate the remote control,
you must install two new AA alkaline batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
Operations
4
Default State :
Device Default : Scientific Atlanta Explorer
2000/3000 & Pioneer Voyager
Volume Default : TV volume and mute through
the TV, with the option of controlling volume and
mute through the Cable Converter. Refer to
Section F for programming the volume and mute
through your Cable Converter.
System On/Off button :
Universal Remote Control, Inc.
This button is designed to send out power
www.universalremote.com
commands for two or all three devices with one
OEE-0049A Rev 07(06/30/04)
button press. Please refer to section E for details.
3 Button Functions
5 Programming the Remote Control.
A. Three-Digit Code Programming Method.
The remote control can be programmed by pressing in a three digit code number that
corresponds to particular manufacturers and brands of Audio/Video equipment.
The three-digit code numbers are listed in the code table of the instruction manual.
STEP1 Turn on the equipment you wish to program. (TV, VCR, or DVD)
STEP2 Press the [DEVICE] button (TV or VCR) to be programmed and the [SELECT] button
simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready
to be programmed.
*Tip : The device LED will stay lit for 20 seconds. The next step must be entered while the LED is on.
STEP3 Point the remote control toward the STEP4 Press the same [DEVICE] button
equipment and enter the three-digit to store the code. The Device
code number assigned to your LED will blink twice to confirm
brand from the code tables. that the code has been stored.
*Tip : The equipment will turn off when the
C. To Find the Three Digit Code
correct three-digit code number has
been entered. You can verify you have Number That was Stored in
selected the correct code by pressing
the Device.
the [MUTE] button, the equipment
should turn on or turn off. STEP1 Press the [DEVICE] button (TV or
VCR) you wish to verify and the
*Note : If there is more than one three-digit
[SELECT ]button simultaneously for 3
number listed for your brand, try one
seconds.
code number at a time until your
equipment turns off.
*Tip : The device LED will turn on for 20
seconds. The next step must be
STEP4 Store the three-digit code number
entered while the LED is on.
by pressing the same [DEVICE]
button once again. The device LED
STEP2 Press the [INFO] button.
will blink twice to confirm that the
The device LED will blink number of times
code has been stored.
indicating the number of each digit of the
*Note : Try all the functions on the remote
code number. Each digit is separated by a 1
control. If any of the functions do not
second interval of the LED being turned off.
work as they should, repeat from Step 2
Example : One blink, three blinks and eight
using the next three-digit code number
blinks with an interval of 1 second
from the same brand list. Make sure
of LED being turned off, indicates
that the VCR/VOD button is in the
the code number 138.
VCR position when using your VCR.
Note : Ten blinks is equal to the number 0.
B. Auto Search Method.
D. Programming a second TV
If the three-digit code numbers assigned to
to VCR Mode.
your brand do not turn off your equipment or
the code tables do not list your brand, you
STEP1 Press the [VCR] button to be
can use the Auto Search Method to find the
programmed and the [SELECT]
correct three-digit code number for your
button simultaneously for 3 seconds.
equipment by the following steps:
*Tip : The device LED will turn on for 20
STEP1 Turn on the equipment you wish to
seconds. The next step must be
operate.
entered while the LED is on.
STEP2 Press the [DEVICE] button (TV or
STEP2 Press the [TV] device button to
VCR) to be programmed and the
pick up the TV code table.
[SELECT] button simultaneously for 3
seconds. The device LED will turn on.
STEP3 Point the remote control toward the
equipment and enter the three-digit
*Tip : The device LED will light on for 20
code number assigned to your TV
seconds. The next step must be
brand from the code tables.
entered while LED is on.
STEP4 Store the three-digit code number by
STEP3 Point the remote control toward the
pressing the [VCR] button once again.
equipment and alternately press the
The device LED will blink twice to
[CH+] (or [CH-]) button and the
confirm that the code has been stored.
[MUTE] button. If the right code
number is sent, the equipment will
E. Programming the System On/Off Button.
turn off.
This is designed to program the System on/off
*Tip : You can verify that you selected the
button so that it can send out up to three
correct code by pressing the [MUTE]
power on/off commands for the devices you
button again. The equipment should
programmed into the remote control.
either turn on or turn off.
STEP1 Press the [CBL] button.
STEP2 Press the [SYSTEM] button and the
[SELECT] button simultaneously for 3
seconds. The [CBL] button will turn
on for 20 seconds.
STEP3 Press the [DEVICE] button you wish
to store in the System On/Off button
and repeat this until you stored all
the power commands into the
System On/Off button.
STEP4 Press the [CH+] button to save the
power commands you stored. The
[CBL] button will blink twice to
confirm the saving.
F. Volume Punch Through:
By following the steps below, the user can
program the volume controls (Volume UP,
Volume Down and MUTE) from one device to
operate in another device mode.
The default volume control settings on the
remote control is TV volume control. If you
wish to store the CABLE volume control in
CBL mode, use the following steps.
STEP1 Press the [CBL] button and the
[SELECT] button simultaneously for
3 seconds.
*Tip : The device LED will light on for 20
seconds. The next step must be
entered while the LED is on.
STEP2 Press the [VOL +] button.
STEP3 Press the [CBL] button.
The device LED will blink twice to
confirm the programming.
To return to original state:
If you wish to restore the TV volume control in
CBL mode, repeat the above steps by
pressing [TV] in STEP 3 .
G. LOW BATTERY WARNING:
When the battery is low (2.0V-2.3V) and
needs to be replaced with fresh batteries,
the remote control LED will blink 2 times in
sequence whenever a [DEVICE] button is
pressed to turn on equipment.
H. Memory Lock System:
This remote control is designed to retain
programmed memory for 10 years even
after batteries are removed from the
remote control.