Download
Share
Print this page
Dell G2723H Service Manual
  1. Manuals
  2. Brands
  3. Dell Manuals
  4. Monitor
  5. G2723H
  6. Service manual
Dell G2723H Service Manual

Dell G2723H Service Manual

Hide thumbs Also See for G2723H:

Advertisement

Quick Links

Download this manual
Service Manual - G2723H
Version: 01
Date: 2022/5/27

Advertisement

loading
Need help?

Need help?

Do you have a question about the G2723H and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Dell G2723H

Summary of Contents for Dell G2723H

  • Page 1 Service Manual - G2723H Version: 01 Date: 2022/5/27...

  • Page 2: Important Safety Notice

    1. Important Safety Notice Product Announcement: ! To ensure using a proper screwdriver, follow the This product is certificated to meet RoHS torque and force listed in assembly and Directive and Lead-Free produced definition. disassembly procedures to unscrew screws. Using approved critical components only is ! Using Lead-Free solder to well mounted the recommended when the situation to replace parts.
  • Page 3 HDMI 1.8 M cable NOTE: For replacement of power cord, connectivity cable and external power supply (if applicable), contact Dell: 1. Go to https://www.dell.com/support. 2. Verify your country or region in the Choose A Country/Region drop-down menu at the bottom-right corner of the page.
  • Page 4 3. Wiring Connectivity Diagram...
  • Page 5 4. How to connect and disconnect power cable/ connectivity cable WARNING: To change power cable/ connectivity cable, switch off power before unplugging the cable and replugging in required cable.
  • Page 6 4. How to connect and disconnect power cable/ connectivity cable...

  • Page 7: Disassembly And Assembly Procedures

    This “Disassembly and Assembly Procedures” is for EMEA only, function key cable and USB cable from the not for other regions. Please note that Dell will deem warranty void connector of the interface board, and then remove if any disassembly is done on the monitors.
  • Page 8 5. Disassembly and Assembly Procedures Use a Philips-head screwdriver to remove 11pcs(9+2) screws for locking the middle bezel with panel module and front bezel. (No.1~9 Screw size= M3x5, Torque=5±0.5kgfxcm; No.10~11 Screw size= M2x3, Torque=1±0.2kgfxcm) Disconnect the power key cable from the connector of the interface board, then release the key by tearing off the tape on the back of the cable.
  • Page 9 5. Disassembly and Assembly Procedures Lift up the bracket chassis module and put it on a Remove the circuit boards from the bracket protective cushion. chassis module carefully, and then disconnect all of the cables. Turn over the bracket chassis module. Remove the Mylar from the hooks of the bracket Use a Philips-head screwdriver to remove 5pcs...
  • Page 10 5. Disassembly and Assembly Procedures Take 1pcs mylar to insert the hooks of the bracket 5.2 Assembly Procedures: Place a bracket chassis base on a protective chassis module to cover the power board as the cushion, then stick 4pcs Silicon sheet on the position picture below shown.
  • Page 11 5. Disassembly and Assembly Procedures Assemble the middle bezel unit with the front bezel and panel module. Use a proper tool to connect the eDP cable to the connector of the panel module. Paste 1pcs shading mylar tape to cover the left T-Con cover as the Use a Philips-head screwdriver to tighten 2pcs picture below shown.
  • Page 12 5. Disassembly and Assembly Procedures Take 1pcs panel lamp cable to connect the power Take 1pcs rear cover and 1pcs joystick key board, board with the panel module, then tear off the then locate the joystick key board to the specific adhesive tape paper on the back of the cable and fix position of the rear cover, then use a Philips-head the lamp cable with 1pcs adhesive tapes, then locate...
  • Page 13 6. Trouble Shooting Instructions Move the assembled rear cover with function key Lift up the monitor to checking the gap between the board close to the assembled unit, then connect front bezel with panel module , then provide power function key cable and USB cable to the connector supply and a video signal to the monitor, then turn on of interface board.
  • Page 14 6. Trouble Shooting Instructions...
  • Page 15 6. Trouble Shooting Instructions...
  • Page 16 6. Trouble Shooting Instructions...
  • Page 17 6. Trouble Shooting Instructions...
  • Page 18 6. Trouble Shooting Instructions...
  • Page 19 6. Trouble Shooting Instructions...