Kinderkraft FIX2GO i-Size Manual
  1. Manuals
  2. Brands
  3. Kinderkraft Manuals
  4. Car Seat
  5. FIX2GO i-Size
  6. Manual
Kinderkraft FIX2GO i-Size Manual

Kinderkraft FIX2GO i-Size Manual

Hide thumbs

Advertisement

Table of Contents

FIX2GO i-Size
MANUAL
MODEL: FIX2GO i-Size
ECE R129.03 v.1.0
MODEL: I-GUARD
ECE.R129.03
ver. 1.2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FIX2GO i-Size and is the answer not in the manual?

Questions and answers

Related Manuals for Kinderkraft FIX2GO i-Size

Summary of Contents for Kinderkraft FIX2GO i-Size

  • Page 1 FIX2GO i-Size MANUAL MODEL: FIX2GO i-Size ECE R129.03 v.1.0 MODEL: I-GUARD ECE.R129.03 ver. 1.2...
  • Page 2 1.0 Usage NOTE! Product graphics serve an illustrative function! The car seat has been designed, tested and approved for use in accordance with the requirements of UN/ECE Regulation No. 129 concerning the approval of child-restraint systems (UN/ECE R129/03). The car seat can be installed in the car in places indicated by the manufacturer in the vehicle manual.
  • Page 3 Hight of the child Car seat positioning Car seat installation ISOFIX + Top-Tether + inner harness straps 76cm-105cm ISOFIX + three-point car seat belt 100cm-150cm Three-point car seat belt...

  • Page 4: Safety Instructions

    2.0 Safety instructions Please take a few minutes to read this instruction manual in order to ensure the proper safety of your child. • The car seat MUST NOT be installed on rearward facing or side facing vehicle seats. • The car seat can only be installed on the vehicle seat equipped with a three-point car seat belt.
  • Page 5 !WARNINGS! Do not use any replacement covers, other than those recommended by the manufacturer, as the cover is an integral part of the safety system of a car seat. Please take a few minutes to read this instruction manual in order to ensure It is recommended to keep the instruction manual of the car seat the proper security of your child.
  • Page 6 accordance with the manufacturer's instructions may pose a threat to In the event of an emergency, it is important to quickly unfasten the car people's life and health. seat belt. This means that the release button of the safety harness is not Protect the car seat from direct sunlight, otherwise your child may be burnt fully secured;...
  • Page 7 Safe use of batteries and power supply Every household is a user of electrical and electronic equipment, as well as Batteries must be inserted with the correct polarity. Dead batteries must be batteries, and therefore a potential generator of waste that is hazardous removed from the product.
  • Page 8 3.0 Unfolding the car seat 1. Place the car seat on the vehicle seat. Keeping your hand on it, pull the backrest of the car seat upwards. 2. You will hear a click indicating that the backrest is locked. Pay attention to the lever that locks the backrest, it should be locked in the upper position.
  • Page 9 4.0 Securing the child 4.1 Securing the child with the internal safety harness 1. Press the safety harness adjustment button while pulling the safety harness straps. Remember! Do not pull on the shoulder pads. 2. Unfasten the safety harness 3. Move the safety harness to the sides of the car seat. 4.

  • Page 10: Tightening The Harness

    4.2 Tightening the harness 1. Remove any slack from the waist part of the safety harness by pulling it up using the shoulder part. 2. Pull the adjustment strap until the harness lies flat on your child's body. IMPORTANT! Make sure that the safety harness is not twisted.
  • Page 11 Adjust the appropriate height of the shoulder part of the safety harness so that the harness enters the car seat backrest flat, horizontally, right above the child's shoulders.
  • Page 12 4.3 Height of the headrest The headrest should fit snugly around your child's head, with the lower part of the headrest at the same height as your child's shoulders. 1. Loosen the safety harness straps fully by pressing the button and pulling the safety harness straps Remember! Do not pull on the shoulder pads.
  • Page 13 The headrest should fit snugly around your child's head, with the lower part of the headrest at the same height as your child's shoulders.
  • Page 14 4.4 Seat inclination adjustment mechanism Important! If the car seat is installed on the vehicle seat using the Top-Tether strap, loosen the Top-Tether strap before adjusting its inclination, and tighten it again after adjusting the inclination. Before installation, make sure that the car seat is in the most upright position in position No.
  • Page 15 5.0 Installation in a vehicle 5.1 ISOFIX installation 1. Before installation, make sure the car seat is in an upright position. The car seat should be placed on the vehicle seat. Put the plastic guides on the ISOFIX arms. Press both buttons on the ISOFIX arms and extend them to their maximum length.
  • Page 16 5.2 Activation of the SAFERIDE SENSOR alarm system The SAFERIDE SENSOR system is an electronic safety system that indicates with an audible alarm the correct installation of the FIX2GO car seat Top Tether strap. 1. Place the headrest in the highest position. 2.Uncover the left side of the backrest cover to expose the car seat shell.
  • Page 17 Battery installation/replacement: To replace the battery, follow the steps below. Unscrew the securing screw on the battery cover. Remove the battery cover. Remove the battery and dispose of the used one in an appropriate container. Insert a new one, observing the polarity (plus towards the replacer).
  • Page 18 5.3 "Top-Tether" installation for the 76 - 105 cm range Note! Before installing the Top-Tether fastening strap, activate the SAFERIDE SENSOR alarm system! The activation procedure is described in section 5.2. 1. Press the strap loosening button to loosen the belt (the strap must long enough to allow the hook to be placed on the anchorage point at the rear of the vehicle seat or in the trunk).
  • Page 19 backrest forward and backward. If installed correctly, the backrest will stay in place. IMPORTANT: The Top-Tether strap must not pass over the headrest of the vehicle. It should pass under the headrest of the vehicle. If it is not possible, remove the headrest of the vehicle (you should check if it is allowed according to the vehicle manual).
  • Page 20 6.0 Stowing away the five-point safety harness 1. Loosen the safety harness as much as possible by pressing the button and pulling on the safety harness. Remember! Do not pull on the shoulder pads. 2. Raise the headrest raise the headrest as high as possible. 3.
  • Page 21 7. Fasten the five-point internal safety harness 8. Open the compartment cover and then put the fastened safety harness into the compartment. 9. Arrange the safety harness flat along the backrest and close the compartment cover. Place the lower backrest panel on the car seat by attaching the rubber bands to the car seat shell.
  • Page 22 7.0 Installation of the car seat Note! The car seat should be placed directly on the vehicle seat in the most vertical position. 7.1 Children between 76 and 105 tall using the ISOFIX system and the Top-Tether in a forward facing position. Important! When using the car seat for the 76-105cm range, the car seat must be placed in a vertical position.
  • Page 23 7.2 Children between 100 and 150 cm - using the ISOFIX connectors and a three-point car seat belt in a forward facing position. Important! When using the car seat for the 100-150cm range, the car seat must be placed in a vertical position. NOTE! For installation in the 100-150 cm range, remember to turn off the SAFERIDE SENSOR system and stow away the Top-Tether strap 1.
  • Page 24 6. Pass the car seat belt through the car seat shoulder guide and waist guides, and then fasten it. You should hear a characteristic "click". 7. Adjust the headrest to your child's height using the adjustment lever. 8. The waist seat belt must run as low as possible across your child's pelvis.
  • Page 25 7.3 Children between 100 and 150 cm - using a three-point car seat belt in a forward facing position. Important! When using the car seat for the 100-150cm range, the car seat must be placed in a vertical position. NOTE! For installation in the 100-150 cm range, remember to turn off the SAFERIDE SENSOR system and stow away the Top-Tether strap.
  • Page 26 6. Pass the car seat belt through the car seat shoulder guide and waist guides, and then fasten it. You should hear a characteristic "click". 7. Adjust the headrest to your child's height using the adjustment lever. 8. The waist seat belt must run as low as possible across your child's pelvis.
  • Page 27 8.0 Removing the car seat with the TT and ISOFIX systems 1. Loosen the Top-Tether strap by pressing the release button while pulling the end of the strap behind the buckle towards yourself. 2. Remove the anchor hook from the vehicle's anchor point 3.

  • Page 28: Removing The Cover

    8.1 Removing the cover 1. Loosen the car seat belt as much as possible by pressing the button and pulling on the car seat belt. Remember! Do not pull on the shoulder pads. 2. Move the headrest to the highest position 3.
  • Page 29 7. Uncover the upper part of the car seat shell by moving the fabric from the backrest to the headrest, then unfasten the elastic bands attached to the shell and uncover its lower part and the seat 8. Remove the elastic bands located on the inside of the headrest, attached to the shoulder guides on both sides of the headrest, by gently stretching them.

  • Page 30: Installing The Cover

    13. Remove the fabric from the car seat sides by pulling it gently towards yourself. 14. Remove the two elastic bands attached to the back of the car seat (between the back of the headrest and the car seat). 15. Slide the fabric off, passing it through the upper part of the car seat 8.2 Installing the cover To put the cover back on - just reverse the above sequence of actions.
  • Page 31 9.0 Folding the car seat Note! To fold the car seat, it is necessary to set the inclination angle to a vertical position! 1. Loosen the car seat belt as much as possible by pressing the button and pulling on the car seat belt. Remember! Do not pull on the shoulder pads.
  • Page 32 The full text of the Warranty Terms and Conditions is available on the NOTE! The car seat must not be used without the cover. website WWW.KINDERKRAFT.COM • The cover is removable and washable with a mild powder and using a program for delicate fabrics (30°C).

Table of Contents