Mountfield SP185 Li Kit Manual

TECHNICAL DATA

[1]	TECHNICAL DATA		CP1 480 Li 48 Series
[2]	Nominal power*	W	1300 ÷ 1500
[3]	Max. motor operating speed *	min-1	2900
[4]	MAX supply voltage	V / DC	48
[5]	NOMINAL supply voltage	V / DC	43,2
[6]	Machine weight *	kg	23 ÷ 29
[7]	Cutting width	cm	46
[8]	Cutting means code		81004460/0 81004346/3
9 10	Sound pressure level Measurement uncertainty	dB(A) dB(A)	82,4 3,0
[11] [10]	Measured acoustic power level Measurement uncertainty	dB(A) dB(A)	94,36 0,99
[12]	Guaranteed acoustic power level	dB(A)	95
[13] [10]	Vibrations level Measurement uncertainty	m/s2 m/s2	< 2,5 1,5

ACCESSORIES

[14]	ACCESSORIES
[15]	Mulching Kit	✓
[16]	Battery, mod.	BT 720 Li 48 BT 520 Li 48 BT 740 Li 48 BT 540 Li 48 BT 750 Li 48 BT 550 Li 48 BT 775 Li 48
[17]	Battery charger, mod.	CG 500 Li 48 CG 700 Li 48 CGF 500 Li 48 CGF 700 Li 48 CGD 500 Li 48 CGD 700 Li 48

* Please refer to the data indicated on the machine's identification label for the exact figure

GENERAL INFORMATION

READ THIS MANUAL CAREFULLY BEFORE USING THE EN MACHINE.

Keep safe for future use.

HOW TO READ THE MANUAL

Some paragraphs in the manual contain important information regarding safety and operation and are emphasised in this manner:

NOTE OR IMPORTANT
these give details or further information on what has already been indicated, and aim to prevent damage to the machine.

This symbol indicates danger. Failure to observe the warning can lead to possible personal and/or third party injury and/or damage.

Whenever reference is made to a position on the machine "front", "back", "left" or "right" hand side, this refers to the operator's working position.

REFERENCES

Figures
The figures in these instructions for use are numbered 1, 2, 3, etc.
The components indicated in the figures are identified with letters A, B, C, and so on.
Reference to component C in figure 2 is indicated with the wording: "See fig. 2.C" or simply "(Fig. 2.C)".
The figures are given as a guide only. The actual pieces can differ from those illustrated in this document.

SAFETY REGULATIONS

TRAINING

Become acquainted with the controls and the proper use of the machine. Learn how to stop the motor quickly. Failure to follow the warnings and instructions may result in fire and/or serious injury.

• Never allow children or persons unfamiliar with these instructions to use the machine. Local laws may establish a minimum age for users.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instructions concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• Never use the machine if the user is tired or unwell, or has taken medicine, drugs, alcohol or any substances which may slow their reflexes and compromise his judgement.
• Do not allow children or other passengers to ride on the machine.
• Bear in mind that the operator or user is responsible for accidents or unexpected events occurring to other people or their property. It is the user's responsibility to assess the potential risk of the area where work is to be carried out and to take all the necessary precautions to ensure his own safety and that of others, particularly on slopes or rough, slippery and unstable ground.
• If the machine is sold or lent to others, make sure that the operator reads the user instructions contained in this manual.

PRELIMINARY PROCEDURES

Personal Protective Equipment (PPE)

• Always wear suitable work attire, hard-wearing safety footwear with non-slip soles and long trousers. Do not operate the machine barefoot or wearing open sandals. Wear hearing protection devices.
• Use of hearing protections can reduce the ability to hear any warnings (shouting or alarms). Be careful of what occurs around you in the work area.
• Wear protective gloves whenever your hands are at risk.
• Never wear scarves, shirts, necklaces, bracelets, loose flowing clothing, laces or ties or any hanging or flapping accessory that could get caught in the machine or in any objects or materials in the work area.
• Tie your hair back if it is long.

Work area/Machine

• Thoroughly inspect the entire work area and remove anything that could be thrown by the machine or damage the cutting means/rotating units (stones, branches, iron wire, bones, etc.).

DURING OPERATION

Work Area

• Do not use the machine in environments at risk of explosion, in the presence of flammable liquids, gas or powder. Power tools create sparks which may ignite the dust or fumes.
• Work only in daylight or with good artificial light in good visibility conditions.
• Keep persons, children and animals away from the working area. Children must be supervised by another adult.
• Avoid working with wet grass, in the rain and when there is a risk of a thunderstorm, especially lightening.
• Do not expose the machine to rain or wet environments. Water entering a power tool will increase the risk of electric shock.
• Pay careful attention to uneven ground (hills, dips), slopes, hidden hazards and obstacles that could limit visibility.
• Be very careful near ravines, ditches or embankments. The machine could overturn if a wheel slides over the edge or if the earth gives way.
• Always mow across a slope and never up and down it, being very careful when changing direction, making sure you have firm footage and that the wheels do not hit any obstacles (such as stones, branches, roots, etc.) that may cause the machine to slide sideways or make you lose control of it.
• Look out for traffic when using the machine near the road.

Behaviour

• Exercise caution when reversing or moving backwards. Look behind you to make sure there are no obstacles before and during operations in reverse gear.
• Never run, always walk.
• Do not allow the lawnmower to pull you along.
• Always keep hands and feet away from the cutting means, when starting and when using the machine.
• Attention: the cutting means will continue to rotate for a few seconds after disengagement or after you have switched off the motor.
• Keep away from the discharge opening.

If something breaks or an accident occurs during mowing, turn off the motor immediately and move the machine away to prevent further damage; if an accident occurs with injuries or third parties are injured, carry out the first aid measures most suitable for the situation immediately and contact the medical authorities for any necessary health care. Carefully remove any debris which could cause damage or injury to persons or animals if ignored.

Use limitations

• Never operate the machine with guards damaged, missing or incorrectly assembled (grass catcher, side discharge guards, rear discharge guards).
• Don't use the machine if the attachments/tools are not installed in their seats.
• Never disengage, deactivate, remove or tamper with the safety systems/micro switches installed.
• Do not strain the machine too much and do not use a small machine for heavy-duty work; if you use the right machine, you will reduce the risk of hazards and improve the quality of your work.

MAINTENANCE, STORAGE

Ensure regular maintenance and correct storage to maintain machine safety and high performance levels.

Maintenance

• Never use the machine with worn or damaged parts. Faulty or worn-out parts must always be replaced and never repaired.
• Be careful during adjustment of the machine to prevent entrapment of the fingers between moving parts of the cutting means and fixed parts of the machine.

The noise and vibration levels shown in these instructions are the maximum levels for use of the machine. The use of an unbalanced cutting element, the excessive speed of movement, or lack of maintenance have a significant influence on noise emissions and vibrations. Consequently, it is necessary to take preventive steps to eliminate possible damage due to high levels of noise and stress from vibration; Maintain the machine well, wear ear protection devices, and take breaks while working.

Storage

• To reduce fire risks, do not leave containers with debris inside a room.

BATTERY / BATTERY CHARGER

The following safety instructions are in addition to the safety requirements provided in the specific battery and battery charger manual delivered with this machine.

• Only use battery chargers recommended by the manufacturer to recharge batteries. An inadequate battery charger may cause electric shock, overheating or corrosive liquid to leak from the battery.
• Use only batteries specifically designed for your power tool. The use of other batteries may cause injuries and fire risks.
• Make sure that the machine is switched off before inserting the battery. Inserting a battery in a machine which is switched on can cause a fire.
• Keep all unused batteries at a distance from paper clips, coins, keys, nails, screws or other small metal objects as contact with the same can cause short circuits. Short circuits between battery contacts can lead to explosion or fires.
• Do not use the battery charger in places where there are inflammable vapours, substances or on easily inflammable surfaces like paper, fabric, etc. During recharge, the battery charger becomes heated and may cause fire.
• When transporting accumulators, make sure the contacts never come into contact with each other and never use metal containers to transport them.

GETTING TO KNOW THE MACHINE

DESCRIPTION OF THE MACHINE AND PLANNED USE

This machine is pedestrian-controlled lawnmower.
The machine is essentially composed of a motor which drives a cutting means enclosed in a casing, equipped with wheels and a handle.

The operator is able to operate the machine and use the main controls, always staying behind the handle at a safe distance from the rotating cutting means. If the operator leaves the machine, the motor and cutting means will stop within a few seconds.

Intended use

This machine is designed and built to cut (and collect) grass in gardens and grassy areas, with a height according to its cutting capacity, driven by an operator walking behind it.

Generally speaking this machine can:

1. Mow the grass and collect it in the grass catcher bag.
2. Mow the grass and discharge it on the ground through the rear part.
3. Mow the grass and discharge it on the ground laterally (if available).
4. Mow the grass, chop it and discharge it on the ground (mulching effect - if available).

The use of special attachments provided for by the Manufacturer as original equipment or which may be purchased separately, allows this work to be done in various operating modes, illustrated in this manual or the instructions that accompany the single attachments.

Improper use

Any other usage not in keeping with the afore-mentioned ones may be hazardous and harm persons and/or damage things.

Examples of improper use may include, but are not limited to:

• Allowing children, animals or other passengers to ride on the machine as they could fall off and injure themselves or compromise safe driving by the operator.
• Letting oneself be transported by the machine.
• Using the machine to tow or push loads.
• Using the cutting means on surfaces other than grass.
• Use the machine for leaf or debris collection.
• Using the machine to trim hedges, or for cutting vegetation other than grass.
• Use of the machine by more than one person.

Improper use of the machine will invalidate the warranty, relieve the Manufacturer from all liabilities, and the user will consequently be liable for all and any damage or injury to himself or others.

User types

This machine is intended for use by consumers, i.e. non-professional operators.
It is intended for "DIY" use only.

The machine must be used exclusively by one operator.

SAFETY SIGNS

The machine has various symbols on it

(Fig. 2).

Their function is to remind the operator of the correct conduct for use, with due care and caution. Meanings of the symbols:

Read the instructions before operating the machine.

Risk of thrown objects. Keep all persons away from the work area whilst working.

Only for lawn mowers with thermal engine.

Only for electric lawn mowers with mains power supply.

Only for electric lawn mowers with mains power supply.

Danger of cutting. Cutting means in motion. Do not insert hands or feet into the cutting means housing.

Be careful when using the sharp cutting means. Do not put hands or feet near or under the opening of the cutting means. The cutting means continues to turn even after the motor has been switched off. Remove the safety key (deactivation device) before any maintenance is carried out.

Any damaged or illegible decals must be replaced. Order replacement decals from an Authorised Service Centre.

IDENTIFICATION LABEL

The identification label holds the following data

(Fig.1).

1. Sound power level.
2. Conformity marking.
3. Year of manufacture.
4. Type of machine.
5. Serial number.
6. Name and address of Manufacturer.
7. Article code.
8. Max. motor operation speed.
9. Weight in kg.
10. Power voltage and frequency.
11. Electrical protection rating.
12. Nominal power.

Write the identification data of the machine in the specific space on the label on the back of the cover page.

Quote the information on the product identification label whenever you contact an Authorised Service Centre.

The example of the Declaration of Conformity is provided on the last pages of the manual.

MAIN COMPONENTS

The machine is composed of a series of main components that have the following functions

(Fig.1.0):

1. Chassis: this is the casing that houses the rotating cutting means.
2. The engine: drives both the cutting means and the wheel traction (if available).
3. Cutting means: the element designed to cut the grass.
4. Rear discharge guard: it is a safety device which prevents objects collected by the cutting means from being projected away from the machine.
5. Side discharge guard (if available): it is a safety device which prevents objects collected by the cutting means from being projected away from the machine.
6. Side discharge chute (if available): apart from discharging the grass on the ground laterally, it also constitutes a safety element, preventing any objects collected by the cutting means from being projected away from the machine.
7. Grass catcher: apart from collecting the mown grass, the grass catcher also constitutes a safety element, preventing any objects collected by the cutting means from being projected away from the machine.
8. Handle: this is the operator's work station. It is long enough to ensure the operator remains at a safe distance from the rotary cutting means whilst working.
9. Battery (if it is not supplied with the machine, see chapter "attachments on request"): provides the energy for starting the motor; its specifications and regulations for use are described in a specific manual.
10. Operator presence lever: this lever enables the cutting means and drive to be operated. The engine stops automatically when the lever is released.
11. Drive engagement lever (if available): this lever engages the drive to the wheels and allows the machine to move forward.
12. Hatch for accessing the battery compartment
13. Safety key (Deactivation device): The key enables / disables the machine electric circuit.
14. Battery charger (if it is not supplied with the machine, see chapter "attachments on request"): device used to recharge the battery.

Strictly observe the indications and the safety regulations described in "SAFETY REGULATIONS" chapter.

ASSEMBLY

Certain components of the machine are not installed in the factory and have to be assembled after unpacking, following the instructions below.

Unpacking and completing the assembly should be performed on a flat and stable surface, with enough space for handling the machine and its packaging.. Do not use the machine until all the indications provided in the "ASSEMBLY" section have been carried out.

UNPACKING

(FIG.3)

1. Carefully open the packaging, paying attention not to lose components.
2. Consult the documentation in the box, including these instructions.
3. Remove all the unassembled parts from the box.
4. Dispose of the box and packaging in compliance with local regulations.

Before assembling, make sure the safety key is not inserted into its housing.

HANDLE ASSEMBLY

Assemble the handle according to the indications in (Fig.4), (Fig.5), (Fig.6):

GRASS CATCHER ASSEMBLY

Assembly the grass catcher as illustrated in (Fig.7).

CONTROLS

SAFETY KEY (DEACTIVATION DEVICE)

The key (Fig.8.A) found inside the battery compartment enables / disables the machine's electrical circuit. Removing the key, the electric circuit is completely deactivated to prevent uncontrolled use of the machine.

Remove the safety key whenever the machine is unused or left unattended.

For certain models, if required, turn the key to "ON" position to activate the electric circuit of the machine to activate its start-up.
Turning the key to "OFF", the electric circuit of the machine is completely deactivated, to prevent any uncontrolled use of the machine.

HANDLE

Operator presence lever

The operator presence lever (Fig.9.A) enables the cutting means.
It is located in front of the handle.
Press the safety button (Fig.9.C) and bring the lever towards the handle in order to start the cutting means. When the lever is released, the motor automatically stops and all functions are disabled.

FIG.9

NOTE
The cutting means engagement is possible only by pressing the yellow button on the right side of the handle and bringing the operator presence lever towards the handle.

Power button

FIG.12

The power button (Fig.12.A) is used to:

		Machine start-up. By pressing the button (Fig.10.A) the LED (Fig.10.B) switches on and the machine is ready for use. NOTE The machine can be switched on only if the operator presence lever and the drive lever are released. NOTE In case the machine is not operated, the LED switches off after 15 seconds and the above-mentioned operation must be carried out again.
		Cutting means engagement. NOTE The cutting means engagement is possible only by pressing the operator presence lever on the handle. See "Start-up".
		Cutting means disengagement. With the cutting means engaged, release the operator presence lever (Fig.10.A); the cutting means stops whilst keeping the machine powered on.

FIG.10

Drive ON lever

The engine has to be always started with the drive disengaged.

This engages the wheel drive and allows the machine to move forward.
It is located behind the handle.

Drive engaged.

The lawn mower is driven forward with the lever pulled against the handle (Fig.9.A). The lawn mower stops moving forward when the lever is released.

Avoid moving the machine backwards when the drive is ON.

For certain models, the forward speed can be adjusted with the selection knob located on the right side of the handle (Fig.10.C).

You can select 6 different levels of speed.

1. 
   Maximum speed (about 5 Km/h).
2. 
   Minimum speed (about 2.5 Km/h).

NOTE
The last speed level selected remains set even after the machine is switched off.

"ECO" button

The "ECO" mode allows to save energy when cutting the grass, optimising the battery life. Press the button (Fig.10.D) to enable or disable the "Eco" mode. This mode is automatically deactivated when the operator presence levers are released.

NOTE
It is not recommended to use the "ECO" function in heavy grass cutting conditions (cutting of dense, high, humid grass).

CUTTING HEIGHT ADJUSTMENT

Lower or raise the chassis to cut the grass at different heights.

Carry out this operation when the cutting means is stationary.

The cutting height is adjusted by using the designated lever (Fig.11.A) that lifts or lowers the chassis to the desired position.

USING THE MACHINE

For instructions regarding the batteries, refer to the specific manual.

PRELIMINARY PROCEDURES

Make sure that the safety key is not inserted in its slot. Place the machine in a stable horizontal position on the ground.

Checking the battery

Before using the machine for the first time after purchase, fully charge the battery following the instructions in the battery booklet.
Before every use of the machine, check the battery charge status according to the instructions in the battery booklet.

Preparing the machine before starting work

NOTE
This machine can be used to mow lawns in various ways.

1. Preparation for grass cutting and collection in the grass catcher:
   1. For side discharge models: make sure that the guard (Fig. 12.A) is lowered and locked by the safety lever (Fig. 12.B).
   2. Insert the grass catcher (Fig.12.C).
2. Preparation for grass cutting and rear grass discharge on the ground:
   1. Lift the rear discharge guard (Fig.13.A) and fit the pin (Fig.13.B).
      
   2. For models with side discharge option: make sure that the guard (Fig. 13.C) is lowered and locked by the safety lever (Fig. 13.D). To remove the pin: see Fig.13.A/B.
3. Preparation for grass mowing and chopping (mulching function):
   Lift the rear discharge guard (Fig.14.A) and insert the chute plug (Fig.14.B) in the discharge opening, keeping it slightly tilted to the right; then fasten it by inserting the two pins (Fig.14.B.1) in the provided holes, until the engagement click is heard.
   For models with side discharge option: make sure that the side discharge guard (Fig. 14.C) is lowered and locked by the safety lever (Fig. 14.D).
   
   FIG.14
4. Preparation for grass cutting and side discharge on the ground:
   1. Lift the rear discharge guard (Fig.15.A) and insert the chute plug (Fig.15.B) in the discharge opening, keeping it slightly tilted to the right; then fasten it by inserting the two pins (Fig.15.B.1) in the provided holes, until the engagement click is heard.
   2. Slightly push the safety lever (Fig.15.C) and lift the side discharge guard (Fig.15.D).
   3. Insert the side discharge chute (Fig.15.E).
   4. Close the side discharge guard (Fig.15.D) so as to lock the side discharge chute (Fig.15.E).
      To remove the side discharge chute:
   5. Slightly push the safety lever (Fig.15.C) and lift the side discharge guard (Fig.15.D).
   6. Release the side discharge chute (Fig.15.E).

SAFETY CHECKS

Always carry out the safety checks before use.

Safety check before every use

• Check the integrity and the correct mounting of all components of the machine;
• make sure that all fastening devices are correctly tightened;
• keep all surfaces of the machine clean and dry.

Machine operating test

Action	Result
Start the machine and engage the cutting means (par. Start-up). Release the operator presence lever (Fig.21 A).	The cutting means should move. The lever should return automatically and rapidly to the neutral position, the engine must switch off and the cutting means must stop within a few seconds.
Start the machine (par. Start-up) and operate the drive lever (par. Cutting height adjustment). Disengage the drive lever.	The wheels should move the machine forward. The wheels should stop and the machine stops moving forward.
Test driving	No abnormal vibrations. No abnormal sound.

If any of the results fail to match the indications provided in the tables, do not use the machine! Contact an Authorised Service Centre to have it checked and repaired if necessary.

START-UP

NOTE
Start the machine on a flat surface without obstacles or high grass.

1. Open the hatch for accessing the battery compartment (Fig.16.A).
   
2. Fit the batteries correctly in their compartments (Fig. 7.2.3.A) pressing down until the end and until you hear it clicks firmly into position, ensuring thus the electrical contact.
3. Insert the safety key until the end (Fig.17.A). If required, turn the key to "ON" position.
   
4. Completely close the hatch again.
5. For models that require using a power button for starting, use the power button (fig. 18.A). The LED stays on for 15 seconds.
   
6. Engage the cutting means by first pressing the safety button (Fig.19.A) and then pressing the operator presence lever (Fig.19.B).
   
7. To engage the traction, press the lever behind the handle (Fig.19.C).

OPERATION

When working, always keep a safe distance from the cutting means, given by the length of the handle.

The battery power reserve (and therefore the lawn surface to be mown before recharging) depends on many factors, described in (par. BATTERY).
During use, the charge status of the batteries is displayed (remaining charge percentage) (Fig.10.E).

If the motor stops because it is overheated while mowing, you must wait approximately 5 minutes before restarting it.

Grass cutting

1. Start moving forward and mowing the grass area.
2. Adjust speed and cutting height (par. Cutting height adjustment.) in relation to lawn conditions (grass height, density and humidity) and the amount of grass to be cut.
   For traction models (par. Handle): It is recommended to avoid mowing on slopes with a degree higher than 15°.
3. The appearance of the lawn will improve if you alternate cutting in both directions at the same height (Fig.20).
   

For side discharge: it is recommended to follow a path so as to avoid discharging the cut grass from the part of the lawn that is yet to be mown.

For mulching or rear grass discharge:

• Always avoid removing a large quantity of grass. Never cut more than one third of the total grass height per single pass (Fig.20).
• Keep the chassis clean (par. CLEANING).

Grass catcher emptying

For grass catcher with contents indicator device:

To remove and empty the grass catcher:

1. Wait until the cutting means stops;
2. Remove the grass catcher (Fig.25.A).
   
   FIG.25

STOPPING THE MACHINE

To stop the machine:

1. Release the operator presence lever (Fig.21 A).
   
2. For models that require using a power button for starting, use the power button (fig. 18.A).
3. Wait until the cutting means stops.

After stopping the machine, it will take a few seconds for the cutting means to stop.

Always stop the machine.

• When moving between work areas.
• When driving on grass free surfaces.
• Every time it is necessary to overcome an obstacle.
• Before adjusting the cutting height.
• Any time the grass catcher is removed or refitted.
• Any time the side discharge chute (if available) is removed or refitted.

AFTER OPERATION

1. Clean (par. CLEANING).
2. If necessary, replace damaged components and tighten any slack screws and bolts.

Remove the safety key whenever the ma- chine is unused or left unattended.

MAINTENANCE

GENERAL INFORMATION

The safety regulations to follow are described in chap. "SAFETY REGULATIONS". Strictly comply with these instructions to avoid serious risks or dangers.

Before commencing any inspections, cleaning or maintenance/adjustments on the machine:

• Stop the machine.
• Remove the safety key, (never leave the key inserted or within the reach of children or unauthorised persons).
• Make sure that all moving parts have come to a complete stop.
• Allow the motor to cool before storing in an enclosed space.
• Read the relevant instructions.
• Use suitable clothing, protective gloves and goggles.
• The frequency and types of maintenance are summarised in the "Maintenance Table". The table will help you maintain your machine's safety and performance. It summarises the main interventions to be made and the frequency applicable to each of them. Carry out the relevant task as soon as it is scheduled to be performed.
• The use of non-genuine and/or incorrectly assembled spare parts and attachments could adversely affect machine operation and safety. The manufacturer shall decline all liability in the event of injuries or damages caused by such parts.
• Genuine spare parts are supplied by Authorised Assistance Centres and Dealers.

Any maintenance and adjustment operations not described in this manual must be carried out by your Authorised Service Centre.

BATTERY

Battery power reserve

Battery power reserve (and therefore the lawn surface that can be mown before recharging is required) mainly depends on:

1. Environmental factors that cause higher energy requirements:
   • Mowing dense, high and/or wet grass.
2. Machine cutting width; wider settings involve higher energy consumption.
3. Operator behaviour that should be avoided:
   • Switching the machine on and off frequently whilst working.
   • Setting a cutting height that is too low for the lawn conditions.
   • Working at a speed that is too high in relation to the amount of grass to be removed.

NOTE
During use, the battery is protected against total drainage with a protective device that switches off the machine and prevents its operation.

To optimise battery power reserve it is always recommended to:

• Cut the grass when the lawn is dry.
• Cut the grass frequently so that it doesn't grow too tall.
• Set a higher cutting height when the grass is very tall, then set a lower height and cut the lawn again.
• Do not use the machine in "mulching" mode with very high grass.
• Use of the "ECO" mode (par. Handle).

If the need arises to use the machine for sessions which exceed the capability of a standard battery, it is possible to:

• Purchase a second standard battery to immediately replace the discharged battery, without compromising the continuity of operations.
• Purchase a battery with an extended power reserve compared to the standard version (par. Batteries).

Battery removal and recharging

1. Open the battery compartment access hatch and remove the safety key.
2. Press the button on the battery (Fig.22.A) and remove the battery (Fig.22.B).
   
3. Insert the battery (Fig.23.B) in its housing in the battery charger (Fig.23.C).
4. Connect the battery charger to a power socket with the voltage indicated on the rating plate.
5. Fully charge the battery according to the instructions in the battery/battery charger booklet.
   

NOTE
The battery is equipped with a protective device that inhibits recharging if the environmental temperature is not between 0 and +45°C.

NOTE
The battery can be recharged at any time, even partially, with no risk of damaging it.

Refitting the battery on the machine

When recharging is completed:

1. Remove the battery from the housing in the battery charger (do not keep recharging when recharging is completed).
2. Disconnect the battery charger from the mains power supply.
3. Open the battery housing hatch (Fig.24.A), insert the battery (Fig.24.B) into its housing pressing down until you hear it click firmly into position, ensuring thus the electrical contact.
   

Completely close the hatch again.

CLEANING

Clean thoroughly following the instructions below every time it is used.

Cleaning the machine

• Always make sure the air intakes are free of debris.
• Do not spray water onto the motor and electrical components, prevent them from getting wet (Fig.26).
  
• Do not use aggressive liquids to clean the chassis.
• To reduce the risk of fire, keep the engine free of grass, leaves residues or excessive grease.
• Always keep the levers, display and buttons free of debris.

Cleaning the cutting means assembly

Remove grass debris and mud accumulated inside the chassis.

For side discharge: remove the discharge chute (if mounted - par. Preliminary procedures.2d.).

Cleaning the grass catcher

(Fig.27.A/B)

NUTS AND BOLTS

Keep all nuts, bolts and screws tight to be sure the equipment is in a safe working condition.

CLEANING THE AIR FILTER

The filter element must always be kept perfectly clean. Proceed as follows:

1. Clean around the air filter grid.
2. Unscrew the screw (Fig.28.B) to remove the grid (Fig.28.A).
   
3. Remove the filter element (Fig.29.A).
4. Blow the filter of wash it with water (Fig.29.A) to remove the dust and residues.
   
   FIG.29
5. Refit the filter element (Fig.29.A) in its housing, refit the grid and tighten the screw (Fig.28.A) and (Fig. 28.B).

• Wear heavy duty gloves.
• Hold the machine in the points offering a safe grip, taking into account the weight and its division.
• Use an appropriate number of people for the weight of the machine and the characteristics of the vehicle or the place where it must be placed or collected.

OCCASIONAL MAINTENANCE

Before commencing any inspections, cleaning or maintenance/adjustments on the machine:

• Stop the machine.
• Remove the safety key, (never leave the key inserted or within the reach of children or unauthorised persons).
• Make sure that all moving parts have come to a complete stop.
• Allow the motor to cool before storing in an enclosed space.
• Read the relevant instructions.
• Use suitable clothing, protective gloves and goggles.

CUTTING MEANS

An improperly sharpened cutting means pulls at the grass and causes the lawn to turn yellow.

Do not touch the cutting means until the key has been removed and the cutting means is completely stationary.

All operations on the cutting means (disassembly, sharpening, balancing, repairing, reassembly and/or replacing) are complex jobs that require special skills as well as special tools; For safety reasons, these jobs are best carried out at a Authorised Service Centre.

Make sure damaged, misshapen or worn cutting means are replaced, together with the securing screws, to preserve balance.

Always use original cutting means bearing the code indicated in the 'Technical Data" table.

Given product evolution, the cutting means listed in the "Technical Data" table may be replaced in time with others having similar interchangeable and operating safety features.

STORAGE

STORING THE MACHINE

When the machine is to be stored away:

1. Wait for the engine to cool.
2. Remove the safety key.
3. Clean (par. CLEANING).
4. Check the integrity of the machine.
5. Store the machine:

• In a dry place.
• Protected from inclement weather.
• In a place where children cannot get to it.
• Making sure that keys or tools used for maintenance are removed.

STORING THE BATTERY

The battery must be kept in a cool, shaded place without humidity.

NOTE
In case of prolonged periods of inactivity, recharge the battery every two months.

HANDLING AND TRANSPORTATION

Whenever the machine is to be handled, raised, transported or tilted you must:

• Stop the machine (par. Stopping the machine) until the moving parts come to a complete halt.
• Wear heavy duty gloves.
• Hold the machine in the points offering a safe grip, taking into account the weight and its division.
• Use an appropriate number of people for the weight of the machine and the characteristics of the vehicle or the place where it must be placed or collected.
• Make sure that machine movements do not cause damage or injuries.

When transporting the machine on a vehicle or trailer, always:

• Use an access ramp of suitable strength, width and length.
• Load the machine with the motor switched off and pushed by an adequate number of people.
• Lower the cutting means assembly.
• Position it so that it cannot cause a hazard for anybody.
• Fasten firmly to the means of transport using ropes or chains to prevent it from tipping over.

MAINTENANCE TABLE

Intervention	Frequency	Notes
MACHINE
Check all fasteners; Safety checks/check controls; Check the rear/lateral discharge guards; Check the grass catcher bag and lateral discharge chute; Check the cutting means.	Before use	par. Safety checks
General cleaning and inspection; Checking for any damage to the machine. If necessary, contact the authorised service centre.	After each use	par. CLEANING
Replacing the cutting means	-	par. Cutting means ***
Check the battery charge status	Before each use	*
Recharge the battery	After each use	par. BATTERY
Cleaning the air filter	Once a month	par. Cleaning the air filter

* Refer to the battery/battery charger manual.
** The operation must be carried out by your Dealer or a specialised Authorised Service Centre
*** Operation to be performed at the first signs of any malfunction

PROBLEM IDENTIFICATION

FOR MACHINES WITH ELECTRONIC CONTROL

If problems persist after having performed the above operations, contact your dealer.

FIG.30

PROBLEM	PROBABLE CAUSE	SOLUTION
After pressing the starter button, the LED does no come ON.	Safety key is not inserted or is inserted incorrectly.	Insert the key (par. Start-up).
	Safety key in "OFF" position.	Turn the safety key to "ON" position (par. Start-up).
	Battery is not inserted or is inserted incorrectly.	Open the hatch and check that the battery is fitted in its housing correctly (par. BATTERY.3).
	Low battery.	Check the battery status and recharge if necessary (par. BATTERY.2).
	Incorrect battery combination.	Check if the battery combination is correct, following the instructions supplied in the "Technical data" table.
After pressing the starter button, the LED does not come ON and the machine sets off a sound signal.	Internal motor anomaly.	Remove the safety key and contact the Authorised Service Centre for checks, replacements or repairs.
The motor shuts down whilst working.	Battery is not inserted correctly.	Open the hatch and check that the battery is fitted in its housing correctly (par. BATTERY.3).
	Low battery.	Check the battery status and recharge if necessary (par. BATTERY.2).
The danger LED lights up (Fig. 30.A) and the machine emits an acoustic signal.	Cutting means blocked.	Turn the machine off, remove the safety key and wear work gloves. Check and eventually remove any obstructions in the machine lower side (par. CLEANING.2) that prevent rotation of the cutting means. If the problem continues, contact the Authorised Service Centre for checks, replacements or repairs (par. Cutting means).
	Machine fault	Remove the safety key and contact the Authorised Service Centre for checks, replacements or repairs.
The danger LED lights up (Fig.30.A).	The thermal protection has tripped due to overheating of the machine.	Wait for at least 5 minutes and restart the machine.
Mowing is difficult.	The cutting means is not in good state.	Contact the Authorised Service Centre for the sharpening or replacement of the cutting means.
Excessive noise and/or vibration is experienced whilst working.	Cutting means fittings are loose or the cutting means is damaged.	Immediately turn off the motor and remove the safety key. Contact the Authorised Service Centre for checks, replacements or repairs (par. Cutting means).
Battery power reserve is low.	Severe working conditions requiring greater current absorption.	Optimise operations (par. BATTERY.1).
	Battery is insufficient for operating requirements.	Use a second battery or extended battery (par. Batteries).
The battery charger is not charging the battery.	Battery is not correctly inserted in the battery charger.	Check it is correctly inserted (par. BATTERY.3).
	Unsuitable environmental conditions.	Recharge the battery in places with suitable temperatures (see battery/battery charger instruction manual).
	Dirty contacts.	Clean the contacts.
	The battery charger is not energised.	Check it is plugged in and the power socket is energised.
	Faulty battery charger.	Replace with an original spare part.
		If the problem persists, refer to the battery/ battery charger manual.

FOR MACHINES WITHOUT ELECTRONIC CONTROL

If problems persist after having performed the above operations, contact your dealer.

PROBLEM	PROBABLE CAUSE	SOLUTION
The engine does not start when using the switch	Safety key is not inserted or is inserted incorrectly.	Insert the key (par. Start-up).
	Safety key in "OFF" position.	Turn the safety key to "ON" position (par. Start-up).
	Battery is not inserted or is inserted incorrectly.	Open the hatch and check that the battery is fitted in its housing correctly (par. BATTERY.3).
	Low battery.	Check the battery status and recharge if necessary (par. BATTERY.2).
	Incorrect battery combination.	Check if the battery combination is correct, following the instructions supplied in the "Technical data" table.
The engine stops and the machine emits an acoustic signal.	Battery is not inserted correctly.	Open the hatch and check that the battery is fitted in its housing correctly (par. BATTERY.3).
	Low battery.	Check the battery status and recharge if necessary (par. BATTERY.2).
	The thermal protection has tripped due to overheating of the motor.	Wait for at least 5 minutes and restart the machine.
	Cutting means blocked.	Turn the machine off, remove the safety key and wear work gloves. Check and eventually remove any obstructions in the machine lower side (par. CLEANING.2) that prevent rotation of the cutting means. If the problem continues, contact the Authorised Service Centre for checks, replacements or repairs (par. Cutting means).
	Machine fault	Remove the safety key and contact the Authorised Service Centre for checks, replacements or repairs.
Mowing is difficult.	The cutting means is not in good state.	Contact the Authorised Service Centre for the sharpening or replacement of the cutting means.
Excessive noise and/or vibration is experienced whilst working.	Cutting means fittings are loose or the cutting means is damaged.	Immediately turn off the motor and remove the safety key. Contact the Authorised Service Centre for checks, replacements or repairs (par. Cutting means).
Battery power reserve is low.	Severe working conditions requiring greater current absorption.	Optimise operations (par. BATTERY.1).
	Battery is insufficient for operating requirements.	Use a second battery or extended battery (par. Batteries).
The battery charger is not charging the battery.	Battery is not correctly inserted in the battery charger.	Check it is correctly inserted (par. BATTERY.3).
	Unsuitable environmental conditions.	Recharge the battery in places with suitable temperatures (see battery/battery charger instruction manual).
	Dirty contacts.	Clean the contacts.
	The battery charger is not energised.	Check it is plugged in and the power socket is energised.
	Faulty battery charger.	Replace with an original spare part.
		If the problem persists, refer to the battery/ battery charger manual.

ATTACHMENTS ON REQUEST

"MULCHING" KIT

Finely chops the cut grass and leaves it on the lawn, instead of collecting it in the grass catcher (for machines equipped with it) (Fig.31).

FOG.31

BATTERIES

Different capacity batteries are available to suit specific operating requirements (Fig. 32). The list of approved batteries for this machine can be found in the "Technical Data" table.

FOG.32

BATTERY CHARGER

Device used to recharge the battery (Fig.33).

FOG.33

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Mountfield SP185 Li Kit Manual