Clone Programmer Troubleshooting - LG 323DCH - 32In Wide Lcd Hdtv Spk 1366X768 Hospital Grade Commercial Mode Setup Manual

Hospital tvs
Hide thumbs Also See for 323DCH - 32In Wide Lcd Hdtv Spk 1366X768 Hospital Grade:
Table of Contents

Advertisement

Warning: Do not connect a clone programmer to a
PPV card installed in the Master or Target TVs, as this
will damage the clone programmer and the PPV card.
Reset Clone Programmer After Static Shock
After replacing exhausted batteries (LT2002 only), or if the
clone programmer behaves strangely after a static shock:
TLL-1100A: Turn the TLL-1100A OFF and then ON.
LT2002: Use a paper clip or similar instrument inserted
through the small hole marked RESET to activate the internal
reset switch and restore normal operation.
After a reset, check the real-time clock setting. It may be
necessary to reset the clone programmer clock from a TV
containing the correct time.
Symptom
Clone Programmer
Clone copies setup in less
than 30 seconds.
Remote does not operate
clone programmer.
Clone menu does not dis-
play on TV screen, TLL-
1100A shows error mes-
sage, or LT2002 LED does
not blink.
Clone menu hard to read.
No time set.
Clone not working.
Clone scans channels
more than once.
Master and Target TVs
Cloning did not work.
(LT2002 only) Clone time
disappeared.
New setup not present.
• After cloning operations are complete, unplug the TLL-1100A/LT2002 from the TV.
• If the TV does not display a picture (blank screen) after a few seconds, just change channels.
206-4096
Possible Cause(s)
Not enough time to copy entire
TV setup.
Wrong Installer Remote.
MPI cord not connected.
TV not turned ON.
(LT2002 only) Weak batteries.
(TLL-1100A only) No charge.
Weak signal.
Time not available.
Clone programmer problem.
Clone should only scan channels
once.
Procedure interrupted.
Different TV models.
Step(s) omitted or not per-
formed.
Batteries were removed.
Target TV not reset.
Troubleshooting (Cont.)

Clone Programmer Troubleshooting

Notes
The TLL-1100A and LT2002 clone programmers are designed
to be used with TVs containing the 221-01006 and later pro-
cessors. Use with earlier TVs may give unpredictable results.
Processors used before the 221-01006-04 have a limited
screen display capability; they cannot display entire screens
as shown in the setup instructions accompanying the clone
programmer. Use the printed menu illustrations in the docu-
mentation as an aid to making your programming choices.
Both Master and Target TVs must be in Pass-through Mode
for cloning purposes. See also IMPORTANT CLONING
INFORMATION on page 30.
Possible Solution(s)
TLL-1100A: Turn the TLL-1100A Off and then ON.
LT2002: Press RESET on clone programmer.
Then redo Learn/Teach. (Learning usually takes about 90 seconds;
Teaching usually takes 3 to 4 minutes.)
Only use an LG Installer Remote to operate clone programmer
with TV.
Connect MPI cord properly, and ensure good connection.
TV must be powered ON for clone programmer to work.
Install four (4) fresh AA high-quality alkaline batteries.
Ensure the TLL-1100A is fully charged or connected to AC power.
Connect TV to a reliable analog channel signal source.
Set time on a TV, and copy time to clone programmer.
• Try a different clone programmer.
• Reset the clone programmer.
Ensure TV is set up correctly, and try cloning again.
Wait until procedure complete message is displayed.
Cloning is only possible with identical model TVs.
Refer to the applicable cloning procedure(s), and make sure all
tasks were performed.
Batteries must remain installed to retain time settings.
Disconnect Target TV from AC power for fifteen (15) seconds.
43

Advertisement

Table of Contents
loading

This manual is also suitable for:

22lg3dch26lg3dch32lg3dch22lg3ddh26lg3ddh32lg3ddh

Table of Contents