MELICONI Easyclean 2+ Manual
  1. Manuals
  2. Brands
  3. MELICONI Manuals
  4. Remote Control
  5. Easyclean 2+
  6. Manual
MELICONI Easyclean 2+ Manual

MELICONI Easyclean 2+ Manual

Hide thumbs

Advertisement

Table of Contents

Easyclean 2+
/ PJN22009
Thank you for choosing a Meliconi remote control.
Before starting to use the product, read carefully and completely this manual and the
safety warnings
The Easyclean 2+ remote control is designed to command a TV and a DECODER (satellite or digital terrestrial).
By LEARN function, you can capture and store infrared signals from other remotes and match at will to one or more buttons.
The MELICONI remote control reproduces infrared signals corresponding to the original; the functions that operate in radio frequency
(e.g. voice commands and pointers) are not supported.
The remote control has a permanent memory, so it does not lose its settings even if there are no batteries in it.
SAFETY WARNINGS
Before using the product, it is recommended to read the safety warnings
included in the package and available at the following link:
https://www.cme.it/meliconi/safety.pdf
INSERTING THE BATTERIES
The remote control requires 2 new 1.5V AAA/LR03 alkaline batteries, not included in the package. Insert with the
correct polarity as shown in figure.
DO NOT use rechargeable batteries.
5
BATTERIES TEST: Press and hold the
button and check that the LED remains on continuously until the button
is released. If the light is off or blinks, the inserted batteries are low, therefore they need replacement.
Do not leave exhausted batteries inserted, as liquid may leak and damage the remote control
SELECTION OF OPERATING MODE
WARNING:
As the remote control is capable of controlling 2 devices, during setup (and also during normal use), you must
select the operation mode; then define which device you want to control. (TV / STB)
To select the operation mode, press for a moment one of the (2) device selection buttons at the top corresponding
to the device you wish to operate (example: TV ).
ACTIVATION OF REMOTE CONTROL
Before using the remote control, for each device you wish to control, it is essential to set a specific code, it matched.
Identify the specific code and set it into the remote control using one of the following ways:
SMARTPHONE
MANUAL
TABLET - WEB
SEARCH
SMARTPHONE - TABLET - WEB
Use the qr-code on the side or connect to the
www.cme.it
page and follow the instructions.
Once you have found the specific code for your device, set it in the remote control as described in the ENTERING
THE CODE DIRECTLY chapter.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Easyclean 2+ and is the answer not in the manual?

Questions and answers

Related Manuals for MELICONI Easyclean 2+

Summary of Contents for MELICONI Easyclean 2+

  • Page 1 By LEARN function, you can capture and store infrared signals from other remotes and match at will to one or more buttons. The MELICONI remote control reproduces infrared signals corresponding to the original; the functions that operate in radio frequency (e.g.

  • Page 2: Manual Search

    BUTTONS AND FUNCTIONS The functions of the buttons on the MELICONI remote control are only available if the original device is equipped with it. Sometimes some functions of the original remote control are not directly present on the MELICONI remote control keypad.

  • Page 3: Child Mode

    3. While the LED remains on, enter the code 1600. 4. While the LED flashes, within 30 seconds, on the MELICONI remote control press the button which you want to delete the function 5. Repeat the procedure from point 3 for each function you want to delete on MELICONI remote control.

  • Page 4: Reset The Remote Control

    If necessary it is possible to completely reset the remote control and bring it back to the initial conditions. WARNING : All user settings will be lost. Operate as follows: • On the MELICONI remote control press and hold the button until the LED lights up; release.

  • Page 5: Learn Function

    - To acquire the keypad of an original remote control when a suitable activation code cannot be found. If no code on the MELICONI remote control is able to command the required appliance properly, you can capture and assign to the various buttons the desired functions of the original remote control.

  • Page 6: Troubleshooting (Faq)

    If necessary try to the RESET OF THE REMOTE CONTROL and carry out a new activation. ● IF SOME FUNCTIONS ARE NOT AVAILABLE ON THE REMOTE CONTROL Usually the MELICONI remote control makes available only the present functions on his keyboard, provided they are available also on the original remote control.

  • Page 7: Disposal Of The Product

    The symbol of the bins, indicating that the batteries should be disposed of according to current regulations; inquire on collection of spent batteries and accumulators in force in your country. Meliconi SpA, Via Minghetti 10 - 40057 Cadriano di Granarolo Emilia, (BO) Italy web: www.meliconi.com email: info@meliconi.com...

This manual is also suitable for:

Pjn22009

Table of Contents