Line Trimmer Safety Warnings; Transportation And Storage; Transporting Lithium Batteries - Aeg A58Ltr18 Original Instructions Manual

PREPARATION
18
■
Wear full eye and hearing protection while operating the product.
V d.c.
If working in an area where there is a risk of falling objects, head
/min
protection must be worn.
■
/min The use of hearing protection may restrict the operator's ability to
hear warning sounds. Pay particular attention to potential hazards
4 mm
around and inside the working area.
0 mm
■
Wear heavy, long trousers, boots, and gloves. Do not wear loose-
.8 kg
fitting clothing, short trousers, or jewellery of any kind. Do not use
the product with bare feet.
■
Secure long hair so that it is above shoulder level to prevent
B (A)
entanglement in moving parts.
5 dB
■
Do not operate the product unless all guards, deflectors, and handles
B (A)
are properly and securely attached.
5 dB
■
Consider the environment in which you are working. Keep the
working area free from wires, sticks, stones, and debris, which if
struck by the cutter can become thrown objects.
m/s
2
BATTERY TOOL USE AND CARE
m/s
2
■
Recharge only with the charger specified by the manufacturer. A
m/s 2
charger that is suitable for one type of battery pack may create a
risk of fire when used with another battery pack.
■
Use power tools only with specifically designated battery packs. The
d to
use of any other battery packs may create a risk of injury and fire.
■
When the battery pack is not in use, keep it away from other metal
rent
objects, like paper clips, coins, keys, nails, screws, or other small
od.
metal objects that can make a connection from one terminal to
not another. Shorting the battery terminals together may cause burns
or a fire.
■
Under abusive conditions, liquid may be ejected from the battery.
ands
Avoid contact. If contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns.

LINE TRIMMER SAFETY WARNINGS

lure
ock,
■
Do not allow children, persons with reduced physical, sensory, or
mental capabilities or lack of experience and knowledge, or people
who are unfamiliar with these instructions to use the product.
must
■
hese
Use the product in the daylight or with good artificial light.
ons
■
Avoid using the product on wet grass.
■
Keep proper footing and balance at all times, and be sure of proper
dren
footing on slopes.
ties.
■
Do not walk backwards when using the product. Walk, never run.
not
■
Keep the head attachment below waist level.
■
Do not operate the product with damaged guards or without guards
e of
in place.
■
Never fit a metal replacement line.
■
Keep hands and feet away from the cutting means at all times and
especially when turning on the product.
hese
the ■
Beware, the cutting means continue to rotate after the product is
turned off.
the ■
Beware of objects thrown by the cutting means. Remove debris like
small stones, gravel, and other foreign objects from the work area
before starting operation. Wires or string may become entangled
a of
with the cutting means.
■
To reduce the risk of injury associated with contacting moving parts,
e of
always turn off the product, remove the battery pack, and allow
both to cool down. Make sure that all moving parts have come to
ts or
a complete stop:
●
before servicing
●
before clearing a blockage
●
before checking, cleaning, and working on the product
●
before changing accessories
●
after striking a foreign object
●
whenever leaving the product unattended
●
whenever performing maintenance
●
whenever the product starts to vibrate abnormally
■
The small blade fitted to the blade guard is designed to trim the
newly extended line to the correct length for safe and optimum
performance. The blade is very sharp. Do not touch the blade,
particularly when cleaning the product.
■
Always ensure that ventilation openings are kept clear of debris.
■
Before use and after any impact, check that there are no damaged
parts on the product. A defective switch or any part that is damaged
should be properly repaired or replaced by an authorised service
centre.
■
Make sure that the cutting head attachment is properly installed and
securely fastened.
■
Make sure that all guards, deflectors, and handles are properly and
securely attached.
■
Do not modify the product in any way. This may increase the risk of
injury to yourself or others.
■
Use only the manufacturer's replacement cutting line. Do not use
any other cutting attachment.
■
Immediately turn off the product and remove the battery pack in
the event of an accident or breakdown. Do not operate the product
again until it has been fully checked by an authorised service centre.
WARNING! Ensure that the line cut-off blade in the guard is
properly positioned and secured before each use.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING! To reduce the risk of fire, personal injury, and
product damage due to a short circuit, never immerse the product,
battery pack, or charger in fluid or allow fluid to flow inside them.
Corrosive or conductive fluids, such as seawater, certain industrial
chemicals, and bleach or bleach-containing products, etc., can cause
a short circuit.

TRANSPORTATION AND STORAGE

■
Turn off the product, remove the battery pack, and allow both to
cool down before storing or transporting.
■
Remove all foreign materials from the product.
■
Do not store or transport the product with the battery pack fitted.
Remove the battery pack, and secure it separately. Store the product
in a cool, dry, and well-ventilated place that is inaccessible to
children. Keep the product away from corrosive agents, such as garden
chemicals and de-icing salts. Do not store the product outdoors.
■
For transportation in vehicles, secure the product against movement
or falling to prevent injury to persons or damage to the product.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national provisions
and regulations.
Follow all special requirements on packaging and labelling when
transporting batteries by a third party.
Ensure that no batteries can come in contact with other batteries or
conductive materials while in transport by protecting exposed connectors
with insulating, non-conductive caps or tape. Do not transport batteries
that are cracked or leaking. Check with the forwarding company for
further advice.
23
23