Yamaha Clavinova CVP-307 Owner's Manual page 204

Song
Songs cannot be selected.
• This may be because the language settings have been
changed. Set the appropriate language for the Song file
name.
• If the size of the Song data is large (300 KB or greater),
the Song cannot be selected because the data is too
large to be read by the instrument.
Song playback does not start.
• "New Song" (a blank Song) has been selected. Make
sure to select an appropriate Song in the Song Selection
display (page 34).
• Make sure to press the SONG [PLAY/PAUSE] button.
• The Song has been stopped at the end of the Song data.
Return to the beginning of the Song by pressing the
SONG [STOP] button.
• In the case a Song to which write-protect has been
applied ("Prot. 2 Edit" is shown at the upper left of the
Song name), the original file may not be in the same
folder. It cannot be played back unless the original file
(showing "Prot.2 Orig" at the upper left of the Song
name) is in the same folder.
• In case of a Song to which write-protect has been
applied ("Prot. 2 Edit" is shown at the upper left of the
Song name), the original file name may have been
changed. Rename the file with the original file name (so
that "Prot.2 Orig" is shown at the upper left of the Song
name).
• In case of a Song to which write-protect has been
applied ("Prot. 2 Edit" is shown at the upper left of the
Song name), the file icon may have been changed. Songs
to which write-protect has been applied cannot be
played back when the file icon of the original has been
changed.
• MIDI Clock may be set to "EXTERNAL." Make sure this is
set to "INTERNAL" (page 198).
Song playback stops before the Song is finished.
• The Guide function is turned on. (In this case, playback
is "waiting" for the correct key to be played.) Press the
[GUIDE] button to turn off the guide function.
The Song last selected before turning off the power is
no longer available.
• If the Song last selected before turning off the power is
contained in external media such as a SmartMedia card,
you'll need to reinsert/reconnect the same media to call
up the Song again.
The measure number is different from that of the
score in the Song Position display, shown by pressing
the [REW]/[FF] buttons.
• This happens when playing back music data for which a
specific, fixed tempo is set.
In the AB Repeat function, the B point cannot be set.
• The A point has not been set. Set the B point only after
setting the A point.
204 CVP-309/307 Owner's Manual
When playing back a Song, some channels do not
play.
• Playback of these channels may be set to "OFF." Turn
playback on for those channels that are set to "OFF"
(page 137).
A Song to which write-protect has been applied
("Prot. 2 Edit" is shown at the upper left of the Song
name) cannot be moved to an ID SmartMedia card.
• If you are using an external card reader, write-protected
Songs cannot be moved to an ID SmartMedia card. Use
the card slot on this instrument.
The Tuning Curve of the piano Voice does not quite
match that of other instruments' Voices.
• The Tuning Curve designed especially for piano Voices
may not sound with the appropriate pitches when used
with other instrument Voices. Set the Tuning Curve to
"FLAT" (page 94).
Guide
The melody still plays back, even when specifying
Track 1 as the part to be muted for one-handed prac-
tice.
• A part other than the melody part has been assigned to
Track 1. Reassign the channel containing the melody to
Track 1 (page 136).
The Guide lamps do not light during Song playback,
even after pressing the [GUIDE] button.
• Make sure to turn on the Guide lamps (page 135).
• Any notes outside of the 88-key range cannot be indi-
cated by the Guide lamps.
The Guide lamps light an octave or two lower/higher
than the actual pitch.
• The Guide lamps sometimes light an octave or two
lower/higher than the actual pitch depending on the
selected Voice.
The lamps in the chord section of the keyboard light.
• The Guide function for chords (page 49) has been
enabled. Turn the Style off by pressing the [ACMP ON/
OFF] button.
The Guide lamps do not indicate how to play chords.
• Make sure that the Guide Mode is set to "FollowLights"
(page 102).
• You cannot check how to play chords with the Guide
lamps if the chord fingering method is set to "Single Fin-
ger," "Full Keyboard" or "AI Full Keyboard." Select
another fingering method (page 102).