Troubleshooting; Side Burner Troubleshooting - Weber E-670 Owner's Manual

PRobLEm
burners burn with a yellow or orange flame, in
conjunction with the smell of gas. (this is normal for
the burner lighting tube.)
symptoms:
burners do not light. -or- burners have a small
flickering flame in the hi position. -or-
barbecue temperature only reaches 250° to 300° in
the hi position.
burner does not light, or flame is low in hi position.
experiencing flare-ups:
m Caution: do not line the slide out
grease tray with aluminum foil.
burner flame pattern is erratic. flame is low when
burner is on hi. flames do not run the whole length
of the burner tube.
inside of lid appears to be "peeling." (resembles
paint peeling.)
Cabinet doors are not aligned.
if problems cannot be corrected by using these methods, please contact the Customer service representative in your area using the contact information on our
web site. log onto www.weber.com
PRobLEm
side burner does not light.
flame is low in hi position.
push button ignition does not work.
if problems cannot be corrected by using these methods, please contact the Customer service representative in your area using the contact information on our
web site. log onto www.weber.com

TRoUbLESHooTING

Inspect Spider/Insect screens for possible obstructions .
(Blockage of holes .)
The excess flow safety device, which is part of the
barbecue to cylinder connection, may have activated .
Is LP fuel low or empty?
Is fuel hose bent or kinked?
Does burner light with a match?
Did you use the snap igniter several times until the main
burner lit? Refer to "MAIN BURNER IGNITION" .
Does the igniter work? Do you see a spark when you
repeatedly use the snap igniter?
Are you preheating barbecue in the prescribed manner?
Are the cooking grates and Flavorizer
coated with burned-on grease?
Is the bottom tray "dirty" and not allowing grease to flow
into catch pan?
Are burners clean?
The lid is porcelain enamel or stainless steel, not paint .
It cannot "peel" . What you are seeing is baked on grease
that has turned to carbon and is flaking off .
this is not a defeCt.
Check the adjustment pin on the bottom of each door.
.
®

SIDE bURNER TRoUbLESHooTING

Is gas supply off?
The excess flow safety device, which is part of the
barbecue to cylinder connection, may have activated .
Is the fuel hose bent or kinked?
Does burner light with a match?
.
®
cHEcK
Clean Spider/Insect screens . Refer to "ANNUAL
MAINTENANCE" .
To reset the excess flow safety device, turn all burner
control knobs and the cylinder valve off . Disconnect
the regulator from the cylinder . Turn burner control
knobs to HI . Wait at least 1 minute . Turn burner control
knobs to OFF . Reconnect the regulator to the cylinder .
Turn cylinder valve on slowly . Refer to "MAIN BURNER
IGNITION" .
Refill LP cylinder .
Straighten fuel hose .
Clean burners . Refer to "MAINTENANCE" .
Make sure to hold the control knob in for two seconds
after snapping the igniter and seeing the orange flame
from the burner lighting tube .
Try manually lighting the burner . Refer to "MAIN
BURNER MANUAL IGNITION" . Call customer service .
All burners on HI for 10 to 15 minutes for preheating .
bars heavily Clean thoroughly . Refer to "CLEANING" .
®
Clean bottom tray .
Clean burners . Refer to "MAINTENANCE" .
Clean thoroughly . Refer to "CLEANING" .
Loosen adjustment nut/s. Slide door/s until aligned.
Tighten nut .
cHEcK
Turn gas supply on .
To reset the excess flow safety device turn all burner
control knobs and the cylinder valve off . Disconnect the
regulator from the cylinder . Turn burner control knobs to
START/HI . Wait at least one minute . Turn burner control
knobs to OFF . Reconnect the regulator to the cylinder .
Turn cylinder valve on slowly . Refer to "SIDE BURNER
IGNITION" .
Straighten hose .
If match lights burner, check igniter . Refer to "SIDE
BURNER MAINTENANCE" .
SoLUTIoN
SoLUTIoN
WWW.WEbER.com
® 31