Advertisement
" Y 5 Z < ^ J I R U S H I
Instruction Manual
FRESH BREW
VACUUM INSULATED
STAINLESS FRENCH PRESS
SK-XAE10
Model No.
Name of Each Part
Accessory
Coffee Scoop
> This product is not leak proof.
> The illustrations used in this instruction manual may vary from the actual product
you have purchased.
( Household Use Only)
Please read these instructions before use.
and keep for future reference.
. • Be sure that all parts are attached
firmly before each use.
i
-Ç
Plunger Set
Knob
( Lid S e t)
Lid Cover
Lid
Lid Gasket
Filter Set )
Grit Block Disk j
Half-Blocked
j
Filter Plate
Mesh
Sealing Ring
S K -X A E (E) / B
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Zojirushi SK-XAE10
Summary of Contents for Zojirushi SK-XAE10
- Page 1 Please read these instructions before use. FRESH BREW and keep for future reference. VACUUM INSULATED STAINLESS FRENCH PRESS . • Be sure that all parts are attached SK-XAE10 Model No. firmly before each use. -Ç Name of Each Part Plunger Set...
- Page 2 How to Brew French Pressed Coffee...
-
Page 3: Important Safeguards
Please follow these instructions to prevent scalding, Important Safeguards deterioration and discoloration of beverages, and malfunction or staining of the product. Keep out of the reach of infants and Do not allow a hot kettle small children. Do not allow them to play to touch the Mouth of the with this product. - Page 4 Please follow these instructions to prevent scalding, Important Safeguards deterioration and discoloration of beverages, and malfunction or staining of the product. Use the product with the Lid Set attached Do not fill the product with a beverage securely, and close the Spout after use. while the Plunger Set is inserted.
-
Page 5: Warnings And Cautions
Warnings & Cautions Avoid dropping or hitting the product Follow the points below when cleaning the product. against hard surfaces. • Do not use chlorine bleach. Damage to plastic parts or the surface of Doing so may cause rust, holes, or other the Main Body may reduce its ability to damage. - Page 6 How to Disassemble / Assemble Parts Plunger Set To Disassemble To Assemble (D Rem ove the Cap by turning in (1) Insert the Rod through the Lid the REMOVE direction. Set and then the Filter Set. The side with the Lid Cover should face up._______ The side with...
- Page 7 How to Disassemble / Assemble Parts (continued) To Disassemble To Assemble (D Push the Tabs on the underside © Attach the Lid Gasket with the of the Lid Cover outward to Ridge facing out. rem ove the Lid Cover. Cross Section Tabs on the Lid Cover Ridge is facing out.
- Page 8 How to Disassemble / Assemble Parts (continued) To Disassemble To Assemble <D Insert your finger between the Attach the Sealing Ring with the Half-Blocked Filter Plate and Grit Ridge facing out. Block Disk to rem ove the Grit •A tta c h the Sealing Ring correctly. Block Disk.
- Page 9 Using the French Press •Thorou ghly clean the Plunger Set and Interior with lukewarm water before use. •The product may initially have a plastic odor, but this will fade with use. < ? •Make sure that all the parts of the Plunger Set are correctly attached before use.
- Page 10 • French Press Coffee Brewing Guideline# Coffee Grounds Serving Size Hot Water (in Zojirushi Coffee Scoop) 1 serving 1 scoop (approx. 8g / 0.28 oz.) 150mL (5 oz.) 6 servings 6 scoops (approx.
- Page 11 Using the French Press (continued) Attach the Plunger Set and steep for 4 minutes Turn the Lid Cover in the direction of the arrow to align STEEP * PRESS with the Tab. ) Lift up the Knob and align the A with the Spout. Insert the Plunger Set into the Main Body.
- Page 12 Using the French Press (continued) ISK-XAE (E) /~B Press down the Knob and pour the coffee Slowly press down the Knob, taking about 10-15 seconds. • If the Knob is difficult to push down, slightly lift the Knob and allow to sit shortly, then press down the Knob again.
- Page 13 Taking Care of Your French Press Clean the product after each use to prevent odors, stain, mold, and to keep the product sanitary. •T h e Rod and Filter Set are hot after use. Allow to cool before cleaning. •B everage may pool in the Filter Plate Set after the final pour. Remove the Plunger Set from the Main Body, then tilt the Plunger Set to drain any remaining beverage from the Filter Plate Set before cleaning.
-
Page 14: Replacement Parts
•W h e n replacing parts, please record the model number and part name beforehand. Parts can be purchased through Zojirushi.com, by contacting Zojirushi Custom er Service, or the store where you purchased the product. Zojirushi Customer Service 1-800-733-6270 www.zojirushi.com... -
Page 15: Troubleshooting Guide
Troubleshooting Guide Problem Cause Solution Check the position and direction in Are the Lid and Lid Gasket which the Lid Gasket is attached, attached correctly? and make sure that the Lid is not loose, (see pg. 7,11) Clean the parts according to the Is the Lid or Lid Gasket instructions, (see pg. - Page 16 Troubleshooting Guide (continued) Problem Cause Solution Fill the product with sufficiently hot beverage up to the correct level. To The product Did you fill the product with retain heat more effectively, does not retain a sufficiently hot beverage? preheat for about 1 minute by filling heat.
Need help?
Do you have a question about the SK-XAE10 and is the answer not in the manual?
Questions and answers