Advertisement
Quick Links
L I N E A / M I L A N O
Tower Cabinet
Adjustable Carousel Corner Tower (Door, Solid Top, 5 Legs) - Fitting Guide
Cabinet Parts
1x
Frontal
16x
1 1/4" Screws
5/8" screws
Tools Required
Drill
Stud
Finder
1x
1x
Corner
Blanking
post
Panel
30x
5x
Shelf Pegs
5x
Legs
Circular
Jigsaw
Saw
1x
Packer Y1
16x
Cover Caps
2x
Toe Kick Clips
Mallet
Screwdriver
1x
2x
Packer Z1
Shelves
2x
L-Brackets
Door Buffers
Clamp
Spirit
Level
Measure
5x
Tape
Page 1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Wren LINEA Tower Cabinet
Summary of Contents for Wren LINEA Tower Cabinet
- Page 1 L I N E A / M I L A N O Tower Cabinet Adjustable Carousel Corner Tower (Door, Solid Top, 5 Legs) - Fitting Guide Cabinet Parts Frontal Corner Blanking Packer Y1 Packer Z1 Shelves post Panel 1 1/4” Screws 5/8”...
- Page 2 Remember to take care when unpacking. Please keep your workspace clean, clear, and tidy when working. This will help keep all items safe from damage. Any unneeded cardboard or plastic should be flattened down and placed in the trash can. A minimum of two people will be needed to lift the cabinet.
- Page 3 Drilling the pilot holes for the packer fixing Packer Z1 should be positioned closely to the center post and in line with the front edge of the cabinet. Position the corner post’s opposite side to the hinge plates. On the cabinet’s front rail and base panel, transfer the 1 1/4”...
- Page 4 Notching out the side panels (when required) In order to allow for any horizontal pipework running behind the cabinet, some cabinets will require the back of the cabinets side to be notched out. Create a notch for the horizontal pipes at the back of the end panels using a jigsaw.
- Page 5 The corner post will be divided into two pieces, Z and Y. The sizes of the pieces will vary based on the room dimensions and the kitchen plan. The correct dimensions will be obtained through the following steps: Positioning the adjacent base cabinet To determine the corner post measurements, position the adjacent base cabinet in line with the wall markings.
- Page 6 When cutting the panel please take into account the thickness of the blade. Cutting of the corner post When using a circular saw, mark the measurement on the back of the corner post panel. Place the panel facing down and cut it into two pieces.
- Page 7 Marking Panel Z Continue the markings down the full length of panel Z. Next, light draw a line in the middle of the two pencil markings. Drill four holes down the center line, ensuring they are equally spaced. Creating the corner post Attach Panel Y to Panel Z to create a corner post, using a clamp to secure the pieces together.
- Page 8 Fixing the corner post to the cabinet Move the adjacent base cabinet away from the corner cabinet. Clamp Panel Z to Packer Z1 on to the corner unit 3/4” from the center post, secure with View from clamps. Use 4x 1 1/4” screw to attach them the back of together, ensuring the screws are equally the cabinet...
- Page 9 No screws are provided for the wall attachment due to variations in wall materials, thickness, and construction. Before drilling into the wall, you MUST check for any hidden services or pipework within the walls. Attaching the tower cabinet to the wall Fix the cabinet to the wall through the L-brackets, as shown in the image (these fixings are not provided).
- Page 10 To attach adjacent tower units to this unit, refer to: Milano Mid Profile - Fitting Guide To attach adjacent base or wall units to this unit, refer to: Milano End Profile - Fitting Guide Placing the shelf into position Remove the masking tape. Position the shelf pegs into the pre-drilled holes.
- Page 11 Adding the door buffers Position 1x door buffer at the top and bottom corners of the cabinet, as illustrated in the image. Removing the hinge cover cap Use a flathead screwdriver to remove the hinge cover cap by inserting it into the slot of the cover cap and twisting.
- Page 12 Altering the soft-close Fit the hinge cover caps to the hinges by pressing down to secure. Adjust the soft-close to suit (if required). The soft-close is adjusted by turning the screw at the top of the hinge clockwise or anti-clockwise. Cleaning the cabinet Finally, the cabinet should be thoroughly cleaned to remove any debris that may have...
Need help?
Do you have a question about the LINEA Tower Cabinet and is the answer not in the manual?
Questions and answers