1. Manuals
  2. Brands
  3. Noraxon Manuals
  4. Security Sensors
  5. Ultium EMG System
  6. Quick start manual

Noraxon Ultium EMG Quick Start Manual

Insole smart lead
Hide thumbs Also See for Ultium EMG:

Advertisement

Table of Contents

Insole Smart Lead Quick Start Guide
Ultium Insole
Quick Start Guide
1
(Rev C Dec 2024)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Ultium EMG and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Noraxon Ultium EMG

Summary of Contents for Noraxon Ultium EMG

  • Page 1 Insole Smart Lead Quick Start Guide Ultium Insole Quick Start Guide (Rev C Dec 2024)
  • Page 2 Note: This is not meant to be a complete manual, but a guide to help you get started with your system. For more detailed instructions on operating the Ultium system and its features please refer to the complete Ultium EMG User Manual, also included with your system. (Rev C Dec 2024)
  • Page 3 Insole Smart Lead Quick Start Guide System Unboxing The Ultium Insole system is packed within a reinforced padded box for storage and protection during transport. Upon arrival, carefully remove all contents and verify the following components are present. Contents will vary depending on the purchased package. Figure 1 - Ultium Receiver (part Figure 2 - EMG Sensor Docking Station (part #883 Figure 3 - EMG Sensor (part...

  • Page 4: Hardware Installation

    Insole Smart Lead Quick Start Guide Hardware Installation Hardware Setup Instructions Step 1 Insert the USB-B (smaller) end of the USB cable (CBL2) into the USB connector on the rear of the Ultium Receiver (880). Insert the opposite end of the USB cable into an available USB port on the computer.
  • Page 5 Insole Smart Lead Quick Start Guide Step 5 Connect the Insole SmartLead (826) to the Ultium Sensor (810). The Ultium Sensor will blink purple after the SmartLead is detected. Step 6 Connect the Insole Sensor (826x) to the Insole SmartLead (826) (Rev C Dec 2024)
  • Page 6 Internet for immediate activation a. Alternatively, email the provided activation ID to activation@noraxon.com b. Noraxon Support will email or respond by phone with the Activation Code Enter the provided Activation Code to remove any restrictions on use. (Rev C Dec 2024)

  • Page 7: Configuring The Hardware

    Within the “General” tab, select the desired settings for the system, i.e., name, sample rate, cutoff filters. Note: If available, firmware updates for the Receiver and Sensors will be indicated here. If using myoSYNC, click the Use Noraxon myoSYNC checkbox. (Rev C Dec 2024)
  • Page 8 Insole Smart Lead Quick Start Guide Additional settings are available within the “Advanced” tab. Note: If multiple Ultium systems are in use, separate networks assignments required for each Receiver. Step 4 Make sure the EMG or SmartLead Sensors are placed in the Charger(s) and the Charger(s) are connected to the Ultium Receiver, then click Detect Sensors in Chargers to load all sensor serial numbers into the MR software.
  • Page 9 Insole Smart Lead Quick Start Guide Step 6 Click Ok to save the hardware settings and close the setup window. Select the Ultium Insole Mode from the Advanced tab in the Ultium Hardware Setup. See below for details about the Insole Modes. (Rev C Dec 2024)
  • Page 10 Insole Smart Lead Quick Start Guide The zone configuration for the Ultium Insoles can be selected from the Advanced tab in the Ultium Hardware Setup as an Insole Mode. 4 Zone Anterior/Posterior Each zone shown by the red outline is an average of the sub-zones.

  • Page 11: Recording A Measurement

    Insole Smart Lead Quick Start Guide Recording a Measurement Step 1 On the Home screen, select or create a subject. Select an application, then select or create a new protocol. Click MEASURE to proceed. Step 2 Insert the Ultium Insole device into the configuration by dragging it from the Available Devices list to the Devices in Your Configuration area.
  • Page 12 Insole Smart Lead Quick Start Guide Step 4 Click ACTIVATE to begin the measurement. You will be prompted to calibrate the insoles before recording. First, have the subject shift all weight to the left foot, then calibrate. Repeat for the right foot. After checking for normal signal display, you are ready to record a measurement.

  • Page 13: Viewing A Record

    Insole Smart Lead Quick Start Guide Viewing a Record To view a previously recorded record, select the Database tab. Records are organized by Project and Subject name. Double click on the record of interested to open the record in the View tab. Further Use Features of MR There are many additional features built within MR3.
  • Page 14 Insole Smart Lead Quick Start Guide Insole Dimensions Insole Sensor Sizes Length Forefoot Heel Thickness Weight Width Width Small Medium Large X-Large Insole Care and Cleaning Extra care must be taken when cleaning the insoles. Clean with isopropyl alcohol or disinfectant wipes. ●...

Table of Contents