Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for STARING STV-135
Summary of Contents for STARING STV-135
- Page 1 STV - 135 STV - 165 USER MANUAL Staring Vibratory Plate STV-135 / STV-165...
-
Page 2: Table Of Contents
..................CONTENTS Introduction ........................2 Applications ........................3 Functions and controls ..................... 3 Accessories ........................3 Hazards and risks ......................3-5 Operation ........................6-8 Care and preventive maintenance ................9-10 Product Specification ....................11-12 Trouble shooting ......................13 Warranty ......................... 14 Maintenance Record ...................... 14 EC Declaration ....................... -
Page 3: Applications
Ensure that the shock absorber and eccentric washer are tightened after adjustment. ACCESSORIES ACCESSORIES MODEL Built-in wheel - for easy transportation. STV-135 series STV-165 series Electric Starter - for diesel Engine STV-165 series Rubber Mat - for brick paving compaction STV-135 series STV-165 series HAZARDS AND RISKS NEVER allow any person to operate the machine without adequate instruction. -
Page 4: Mechanical Hazards
MECHANICAL HAZARDS DO NOT operate the machine unless all protective guards are in place. KEEP handles and feet clear of rotating and moving parts as they will cause injury if contacted. ENSURE that the motor operation switch is in the OFF position and the spark plug ignition lead is disconnected before removing the guards or making adjustments. -
Page 5: Chemical Hazards
CHEMICAL HAZARDS DO NOT operate or refuel a petrol or diesel motor in a confined area without adequate ventilation. CARBON MONOXIDE exhaust gases from internal combustion motor driven units can cause death in confined spaces. NOISE HAZARDS EXCESSIVE NOISE can lead to temporary or permanent loss of hearing. WEAR an approved hearing protection device to limit noise exposure. -
Page 6: Operation
OPERATION Pre-start-up inspection The following Pre-start-up inspection must be performed before the start of each work session or after every four hours of use, whichever is first.. If any fault is discovered, the compactor must not be used until the fault is rectified. Thoroughly inspect the compactor for signs of damage. -
Page 7: Petrol Engine
OPERATION To eliminate any possible water and dirt residue from the tank bottom, remove the plug (A) and open the cock (B) to enable discharging. Once the operation is over, close the cock and screw back the protecting plug. Accelerator at 50 % speed. 10. - Page 8 OPERATION The machine is best suited to the compaction of bituminous and granular materials e.g. granular soils such as silt and clay are best compacted using the impact force produced by a vibrating rammer. Where possible the site should be graded and leveled before commencing compaction. Correct moisture content in soil is vital to proper compaction.
-
Page 9: Care And Preventive Maintenance
CARE AND PREVENTIVE MAINTENANCE • Check the oil level in the motor crankcase daily. • Inspect the rubber anti vibration mounts for wear or deterioration. • If the optional water tank is fitted inspect the water hose and its connections to ensure that they do not leak. -
Page 10: Air Filter
Changing Vibrator OIL / Vibrator Grease When changing the vibrator oil, remove the drain plug located at the bottom-right of the vibrator, and simply tip the compactor to drain the oil. Note that the oil will drain more easily while it is hot. For TP5020 series, replace the oil with 405ML of SAE1SW-40 API SG motor oil;... -
Page 11: Product Specification
PRODUCT SPECIFICATIONS BODY Model STV-135 STV-165 Centrifugal force kN Compaction depth cm Plate size (L x W) mm 650×400 690×500 Frequency Hz Travel speed cm/s Packing size mm 750×400×930 860×570×930 Engine brand HONDA HONDA Engine Model GX160 GX270 Engine output hp... -
Page 12: Trouble Shooting
PRODUCT SPECIFICATIONS STV-135 Series: 78 x 45 x 124 cm (L x W x H) STV-165 Series: 83 x 57 x 124 cm (L x W x H) TROUBLE SHOOTING 1. Always shut off engine when transporting machine. 2. Make sure lifting device has enough capacity to hold machine (see identification plate on machine for weight). - Page 13 TROUBLE SHOOTING SYMPTOM POSSIBLE CAUSES SOLUTION Spark plug bridging? Check gap, insulation or replace spark plug. Difficult to start, Carbon deposit on spark plug? Clean or replace spark plug. “fuel is available, but no SPARK at Short circuit due to deficient Check spark plug insulation, replace if worn.
-
Page 14: Warranty
WARRANTY These products are covered by warranty for a period of 1 year from the date of purchase against defects in material or workmanship provided that: • The product concerned has been operated and maintained in accordance with the operating instructions. •... - Page 16 Staring A/S Starengvej 9-11 DK-9700 Brønderslev Tlf.: +45 9882 1622 staring@staring.dk CVR.nr. DK 2767 2701 staring.dk...
Need help?
Do you have a question about the STV-135 and is the answer not in the manual?
Questions and answers