Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hunter Revolutions Solaris
Summary of Contents for Hunter Revolutions Solaris
- Page 1 220V 50/60Hz 17.6lbs (8.0kg) r082724...
- Page 2 This manual will help you install, operate, and maintain your new fan. These instructions are designed to make installation and assembly as simple and efficient as possible. Important Instructions: Keep Instructions for future use Be sure to read the entire manual before beginning installation and save any extra parts for future use. The mounting of the suspension system shall be performed by the manufacturer, its service agent, or suitably quali- fied persons.
-
Page 3: Table Of Contents
Congratulations! You have chosen the best. Your new Revolutions ceiling fan will provide you with many years of comfort and satisfaction. Table of Contents Unpacking Your Fan Tools and Materials Required Install Mounting Bracket Select Type of Installation Hang Down Style Hugger Style Electrical Connections Blade Attachment... -
Page 4: Unpacking Your Fan
ME012-01 08/27/2024... -
Page 5: Tools And Materials Required
Tools and Materials Required • Phillips screw driver • Flat Head screw driver • Adjustable pliers or wrench • Step Ladder • Wire Cutter • Electrical tape Install Mounting Bracket 1. To avoid possible electrical shock, be sure electricity is turned off at the main power panel before wiring. -
Page 6: Select Type Of Installation
Select Type of Installation Hugger Hang Down This method is preferred if the ceiling is This method is preferred if maximum sloped, vaulted, or if the ceiling is extra high headroom is required. The celing must not and requires the use of a downrod. be at and not sloped. -
Page 7: Hugger Style
2. Tighten the two downrod setscrews. Some models have locknuts for the setscrew to ensure the setscrew is fully seated against the down rod. It is necessary to back off the locknut until it contacts the setscrew head prior to tightening the setscrew. When the setscrew is tightened against the downrod, the locknut should then be tightened against the connector yoke. -
Page 8: Electrical Connections
Electrical Connections 1A. Four wires are connected to the top of the fan. 1B. Wire cutters are recommended for this next step. Align the plastic-sheathed cable with the Black: “Hot” Power for the fan notch that matches the wire gauge 18awg and Blue: “Hot”... -
Page 9: Blade Installation
Blade Installation 1. Attach blade brackets to blades using the blade bracket screws (1), fabric washers (2), and nuts (3) provided (Fig.7A). 2. Check the motor for plastic shipping stabilizer tabs (1), and remove them if they are present. 3. Attach blade assembly to motor using the provided motor screws. To attach the blade assembly, rotate the installation window on the bottom of the light kit. -
Page 10: Operation
Operation 1. Restore electrical power by turning on the electricity at the main fuse box. 2. Turn on the wall switch 3. Your fan has 2 controls on the switch housing. Speed Control Direction Control Pull Chain Switch Reverse Slide Switch (pull gently) (up and down) Pull Speed... -
Page 11: Troubleshooting
Troubleshooting FAN WILL NOT START: 1. Check all fuses or circuit breakers. Replace if missing. 2. Turn off electrical power and check all wire connections to fan and in switch housing. FAN IS NOISY 1.Use of standard light rheostat or continuously variable fan speed wall control will always cause harmonic distortions or a huming noise. - Page 12 Revolutions 52” Solaris Indoor Ceiling Fan Part # Description Mounting Bracket Wooden Screws, Flat Washer Ball Downrod Screws Canopy Screws Upper housing Motor Lower housing Reverse switch Pull Chain Switch Blade arms Screws Screws Blades Ground wire Screw Screw Lock pin Screws Light housing Pull chain switch...
Need help?
Do you have a question about the Revolutions Solaris and is the answer not in the manual?
Questions and answers