Subscribe to Our Youtube Channel
Related Manuals for Banner K50 Pro Select Series
Summary of Contents for Banner K50 Pro Select Series
- Page 1 K50 Pro Select Touch Product Manual Original Instructions p/n: 240396 Rev. B 19-Feb-25 © Banner Engineering Corp. All rights reserved. www.bannerengineering.com...
-
Page 2: Table Of Contents
Elevated Mount System....................................15 Chapter 6 Product Support and Maintenance ..............16 Clean with Mild Detergent and Water ................................16 Repairs ........................................16 Contact Us ........................................16 Banner Engineering Corp Limited Warranty..............................16 © Banner Engineering Corp. All rights reserved. www.bannerengineering.com... -
Page 3: Chapter 1 Features
Bright, uniform touch button • Three default colors in one device (Green, Red, Yellow) • Programmable using Banner's Pro Editor software and Pro Converter Cable • Translucent polycarbonate dome • Rugged IP66, IP67, IP69K per ISO 20653 and UL Type 4X and UL Type 13 design •... -
Page 4: Chapter 2 Wiring
Load wh (2) wh (2) Pin 4 (Black) is Output 1. Touch actuation toggles the gy (5) gy (5) output. GRY3 Multicolor Color/Function Definition Green Yellow Input 1 Input 2 19-Feb-25 © Banner Engineering Corp. All rights reserved. page 4 of 17 www.bannerengineering.com... -
Page 5: Chapter 3 Pro Editor
K50 Pro Select Touch Button Pro Editor Program Options ..........................5 Chapter 3 Pro Editor Use Banner's Pro Editor software and Pro Converter Cable to create custom configurations by selecting different colors, flash patterns, and animations. For more information visit www.bannerengineering.com/proeditor. -
Page 6: Device Logic Mode - Four State Full Logic
State 4: Input Active, Touch Active Device Logic Mode – Three State Advanced Control When using Three State Advanced Control, four device states are activated by two input wires. The touch button toggles the output(s) with no device state change. page 6 of 17 © Banner Engineering Corp. All rights reserved. 19-Feb-25 www.bannerengineering.com... -
Page 7: Global Parameters And Advanced Settings
Output 1 is Normally input. When an actuator device is connected, the following Advanced Settings can be accessed by clicking on the AdvancedSettings menu. When Output Type on Touch is set to Latching mode, output state and device state transitions both occur on the leading edge of touch input. 19-Feb-25 © Banner Engineering Corp. All rights reserved. page 7 of 17 www.bannerengineering.com... - Page 8 Remember Touch State on Power Loss the touch state will be retained when power to the device is lost. When OFF the touch state will be reset when power to the device is lost. page 8 of 17 © Banner Engineering Corp. All rights reserved. 19-Feb-25 www.bannerengineering.com...
-
Page 9: Chapter 4 Specifications
< 2 V DC at 10 mA < 2.5 V DC at 150 mA OFF-State Leakage Current: < 10 µA at 30 V DC Output Response Time Power-Up Delay: 500 milliseconds maximum Input Response: 40 milliseconds maximum Output Response: 300 milliseconds maximum 19-Feb-25 © Banner Engineering Corp. All rights reserved. page 9 of 17 www.bannerengineering.com... -
Page 10: Fcc Part 15 Class B For Unintentional Radiators
(2) il doit tolérer toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité du dispositif. Refer to CIE 1931 chromaticity diagram or color chart to show equivalent color with indicated color coordinates. Actual coordinates may differ by 10%. page 10 of 17 © Banner Engineering Corp. All rights reserved. 19-Feb-25 www.bannerengineering.com... -
Page 11: Dimensions
All measurements are listed in millimeters [inches], unless noted otherwise. The measurements provided are subject to change. 50.0 mm (1.97") 35 mm (1.38") 51 mm (2.01") 64 mm (2.52") M30 x 1.5 M12 x 1 19-Feb-25 © Banner Engineering Corp. All rights reserved. page 11 of 17 www.bannerengineering.com... -
Page 12: Chapter 5 Accessories
Required for connection to the configuration software CSB-M1251FM1251M • 5-pin parallel Y splitter (Male-Male-Female) • For full Pro Editor preview capability • Requires external power supply, sold separately PSW-24-1 • 24 V DC, 1 A power supply • 2 m (6.5 ft) PVC cable with M12 quick disconnect • Provides external power with splitter cable, sold separately PSW-24-2 • 24 V DC, 2 A power supply • 3.5 m (11.5 ft) PVC cable with M12 quick disconnect • Provides external power with splitter cable, sold separately 19-Feb-25 © Banner Engineering Corp. All rights reserved. page 12 of 17 www.bannerengineering.com... -
Page 13: Cordsets
V-clamp, flat bracket and fasteners for mounting to pipe or extensions • Clamp accommodates 28 mm dia. tubing or 1 in. square extrusions • 30 mm hole for mounting sensors Hole size: A= ø 31 19-Feb-25 © Banner Engineering Corp. All rights reserved. page 13 of 17 www.bannerengineering.com... - Page 14 12-gauge 304 stainless steel • Easy sensor mounting to extrude rail T-slot 68.9 36.3 • Metric- and inch-size bolt available Bolt thread: SMB30FA, A= 3/8 - 16 × 2 in; SMB30FAM10, A= M10 - 1.5 × 50 Hole size: B= ø 30.1 page 14 of 17 © Banner Engineering Corp. All rights reserved. 19-Feb-25 www.bannerengineering.com...
-
Page 15: Wash-Down Cover
• Compatible with most industrial environments 600 mm (24 in) long 600 mm (24 in) long SOP-E12-900A SOP-E12-900AC 900 mm (36 in) long 900 mm (36 in) long 19-Feb-25 © Banner Engineering Corp. All rights reserved. page 15 of 17 www.bannerengineering.com... -
Page 16: Chapter 6 Product Support And Maintenance
Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. - Page 17 LinkedIn X (formerly Twitter) Facebook © 2025. All rights reserved. www.bannerengineering.com...
Need help?
Do you have a question about the K50 Pro Select Series and is the answer not in the manual?
Questions and answers